Hello You can use the filter ParticleToPathLines on the TableToPoints filter to visualize the path of your particle.
Mathieu Westphal On Tue, Jul 26, 2016 at 5:39 PM, Konstantinos Panagiotou < [email protected]> wrote: > I hope this time is ok > the vtk file is the flow solution,the csv file is the particle data > > kostas > ------------------------------ > *From: *"Mathieu Westphal" <[email protected]> > *To: *"Konstantinos Panagiotou" <[email protected]> > *Cc: *"ParaView" <[email protected]> > *Sent: *Wednesday, July 27, 2016 12:24:04 AM > > *Subject: *Re: [Paraview] plume tracking-trajectory > > I am unable to load your pvsm. > Please provide all the data needed by your pvsm in order for me to load it. > > Mathieu Westphal > > On Tue, Jul 26, 2016 at 5:03 PM, Konstantinos Panagiotou < > [email protected]> wrote: > >> hello >> i have loaded the csv data and a vtk file,a cube basicly, in which the >> flow solution is stored >> >> ------------------------------ >> *From: *"Mathieu Westphal" <[email protected]> >> *To: *"Konstantinos Panagiotou" <[email protected]> >> *Cc: *"ParaView" <[email protected]> >> *Sent: *Tuesday, July 26, 2016 11:53:41 PM >> >> *Subject: *Re: [Paraview] plume tracking-trajectory >> >> Your data does not seem to be correctly formated. >> Can you send me an associated pvsm file ? >> >> Mathieu Westphal >> >> On Tue, Jul 26, 2016 at 4:08 PM, Konstantinos Panagiotou < >> [email protected]> wrote: >> >>> Dear Mathieu, >>> i have installed cmake and qt in order to use cmake command to convert >>> to .vtp. However,i need to add some additional packages which i am not >>> familiar with. >>> So, instead of converting to .vtp, i am sending you in zip form two >>> files with different formats, vtk and csv respectively, files which i have >>> loaded to paraview and being able to animate them using glyph. they are few >>> KB each, it is the minimum i could do in order to keep the example as >>> simple as possible for possible extension later on. >>> Sincerely, >>> Kostas >>> >>> ------------------------------ >>> *From: *"Mathieu Westphal" <[email protected]> >>> *To: *"Konstantinos Panagiotou" <[email protected]>, >>> "ParaView" <[email protected]> >>> *Sent: *Tuesday, July 26, 2016 8:06:16 PM >>> >>> *Subject: *Re: [Paraview] plume tracking-trajectory >>> >>> Please keep the ml in the loop so everyone can follow this. >>> >>> Please open you csv data, save it as a .vtp file and send it to me (if >>> it's not too big) >>> >>> Regards, >>> >>> Mathieu Westphal >>> >>> On Tue, Jul 26, 2016 at 12:55 PM, Konstantinos Panagiotou < >>> [email protected]> wrote: >>> >>>> Hello Mathieu, >>>> i have applied the Temporal ParticlePath filter,however i havent seen >>>> any change. I mean, when i apply glyph to the input data, i can activate >>>> this filter and apply it to the input data,either vtk or csv point data. >>>> However, i havent managed yet to see trajectories of the particles, >>>> only the position of the particle or particles at a specific time step.I >>>> have searched and I have seen in other posts in the forum referring to the >>>> same issue, that the operation interface of the newest vesrion of paraview >>>> is different than the previous ones for the specific function. Can you >>>> guide me pls if you can? :) >>>> >>>> Thanks again, >>>> Kostas >>>> ------------------------------ >>>> *From: *"Mathieu Westphal" <[email protected]> >>>> *To: *"Konstantinos Panagiotou" <[email protected]> >>>> *Cc: *"ParaView" <[email protected]> >>>> *Sent: *Thursday, July 21, 2016 6:16:27 PM >>>> *Subject: *Re: [Paraview] plume tracking-trajectory >>>> >>>> >>>> Hello >>>> >>>> You should have a look to ParticlePath filter. >>>> >>>> Regards >>>> >>>> Mathieu Westphal >>>> >>>> On Thu, Jul 21, 2016 at 10:38 AM, Konstantinos Panagiotou < >>>> [email protected]> wrote: >>>> >>>>> Hi, >>>>> i am having a problem on plotting the trajectory of a single particle >>>>> at the top of a flow solution. Particularly, i have a csv file, which is >>>>> named text0000.csv,inside which i have 4 columns, x,y,z,t.in >>>>> addition, i have additional files text0001.csv,text0002.csv etc, with one >>>>> row each( variables' values at each time step) >>>>> When i load them to the paraview project,i have no problem on >>>>> performing the animation.However, i also want to have particle's >>>>> trajectory >>>>> while it evolves, that is,having lines connecting the updated points with >>>>> the previous ones. But i havent managed to do that yet. I have installed a >>>>> paraview version 5.0.1. pls help me,what i should do? >>>>> _______________________________________________ >>>>> Powered by www.kitware.com >>>>> >>>>> Visit other Kitware open-source projects at >>>>> http://www.kitware.com/opensource/opensource.html >>>>> >>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>> http://paraview.org/Wiki/ParaView >>>>> >>>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>>> >>>>> Follow this link to subscribe/unsubscribe: >>>>> http://public.kitware.com/mailman/listinfo/paraview >>>>> >>>> >>>> >>>> >>> >>> >> >> > >
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
