No ratings necessary, my pleasure to help. Regards,
Mathieu Westphal On Tue, Jul 26, 2016 at 5:53 PM, Konstantinos Panagiotou < [email protected]> wrote: > Thanks a lot!! > very simple answer :) I wish you all the best.And thanks for your patient. > Btw, can i rate your answer somehow? i am very new at that site and in > paraview > > Sincerely, > Kostas > > > ------------------------------ > *From: *"Mathieu Westphal" <[email protected]> > *To: *"Konstantinos Panagiotou" <[email protected]>, > "ParaView" <[email protected]> > *Sent: *Wednesday, July 27, 2016 12:48:41 AM > > *Subject: *Re: [Paraview] plume tracking-trajectory > > Hello > > You can use the filter ParticleToPathLines on the TableToPoints filter to > visualize the path of your particle. > > Mathieu Westphal > > On Tue, Jul 26, 2016 at 5:39 PM, Konstantinos Panagiotou < > [email protected]> wrote: > >> I hope this time is ok >> the vtk file is the flow solution,the csv file is the particle data >> >> kostas >> ------------------------------ >> *From: *"Mathieu Westphal" <[email protected]> >> *To: *"Konstantinos Panagiotou" <[email protected]> >> *Cc: *"ParaView" <[email protected]> >> *Sent: *Wednesday, July 27, 2016 12:24:04 AM >> >> *Subject: *Re: [Paraview] plume tracking-trajectory >> >> I am unable to load your pvsm. >> Please provide all the data needed by your pvsm in order for me to load >> it. >> >> Mathieu Westphal >> >> On Tue, Jul 26, 2016 at 5:03 PM, Konstantinos Panagiotou < >> [email protected]> wrote: >> >>> hello >>> i have loaded the csv data and a vtk file,a cube basicly, in which the >>> flow solution is stored >>> >>> ------------------------------ >>> *From: *"Mathieu Westphal" <[email protected]> >>> *To: *"Konstantinos Panagiotou" <[email protected]> >>> *Cc: *"ParaView" <[email protected]> >>> *Sent: *Tuesday, July 26, 2016 11:53:41 PM >>> >>> *Subject: *Re: [Paraview] plume tracking-trajectory >>> >>> Your data does not seem to be correctly formated. >>> Can you send me an associated pvsm file ? >>> >>> Mathieu Westphal >>> >>> On Tue, Jul 26, 2016 at 4:08 PM, Konstantinos Panagiotou < >>> [email protected]> wrote: >>> >>>> Dear Mathieu, >>>> i have installed cmake and qt in order to use cmake command to convert >>>> to .vtp. However,i need to add some additional packages which i am not >>>> familiar with. >>>> So, instead of converting to .vtp, i am sending you in zip form two >>>> files with different formats, vtk and csv respectively, files which i have >>>> loaded to paraview and being able to animate them using glyph. they are few >>>> KB each, it is the minimum i could do in order to keep the example as >>>> simple as possible for possible extension later on. >>>> Sincerely, >>>> Kostas >>>> >>>> ------------------------------ >>>> *From: *"Mathieu Westphal" <[email protected]> >>>> *To: *"Konstantinos Panagiotou" <[email protected]>, >>>> "ParaView" <[email protected]> >>>> *Sent: *Tuesday, July 26, 2016 8:06:16 PM >>>> >>>> *Subject: *Re: [Paraview] plume tracking-trajectory >>>> >>>> Please keep the ml in the loop so everyone can follow this. >>>> >>>> Please open you csv data, save it as a .vtp file and send it to me (if >>>> it's not too big) >>>> >>>> Regards, >>>> >>>> Mathieu Westphal >>>> >>>> On Tue, Jul 26, 2016 at 12:55 PM, Konstantinos Panagiotou < >>>> [email protected]> wrote: >>>> >>>>> Hello Mathieu, >>>>> i have applied the Temporal ParticlePath filter,however i havent seen >>>>> any change. I mean, when i apply glyph to the input data, i can activate >>>>> this filter and apply it to the input data,either vtk or csv point data. >>>>> However, i havent managed yet to see trajectories of the particles, >>>>> only the position of the particle or particles at a specific time step.I >>>>> have searched and I have seen in other posts in the forum referring to the >>>>> same issue, that the operation interface of the newest vesrion of paraview >>>>> is different than the previous ones for the specific function. Can you >>>>> guide me pls if you can? :) >>>>> >>>>> Thanks again, >>>>> Kostas >>>>> ------------------------------ >>>>> *From: *"Mathieu Westphal" <[email protected]> >>>>> *To: *"Konstantinos Panagiotou" <[email protected]> >>>>> *Cc: *"ParaView" <[email protected]> >>>>> *Sent: *Thursday, July 21, 2016 6:16:27 PM >>>>> *Subject: *Re: [Paraview] plume tracking-trajectory >>>>> >>>>> >>>>> Hello >>>>> >>>>> You should have a look to ParticlePath filter. >>>>> >>>>> Regards >>>>> >>>>> Mathieu Westphal >>>>> >>>>> On Thu, Jul 21, 2016 at 10:38 AM, Konstantinos Panagiotou < >>>>> [email protected]> wrote: >>>>> >>>>>> Hi, >>>>>> i am having a problem on plotting the trajectory of a single particle >>>>>> at the top of a flow solution. Particularly, i have a csv file, which is >>>>>> named text0000.csv,inside which i have 4 columns, x,y,z,t.in >>>>>> addition, i have additional files text0001.csv,text0002.csv etc, with one >>>>>> row each( variables' values at each time step) >>>>>> When i load them to the paraview project,i have no problem on >>>>>> performing the animation.However, i also want to have particle's >>>>>> trajectory >>>>>> while it evolves, that is,having lines connecting the updated points with >>>>>> the previous ones. But i havent managed to do that yet. I have installed >>>>>> a >>>>>> paraview version 5.0.1. pls help me,what i should do? >>>>>> _______________________________________________ >>>>>> Powered by www.kitware.com >>>>>> >>>>>> Visit other Kitware open-source projects at >>>>>> http://www.kitware.com/opensource/opensource.html >>>>>> >>>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>>> http://paraview.org/Wiki/ParaView >>>>>> >>>>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>>>> >>>>>> Follow this link to subscribe/unsubscribe: >>>>>> http://public.kitware.com/mailman/listinfo/paraview >>>>>> >>>>> >>>>> >>>>> >>>> >>>> >>> >>> >> >> > >
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
