Thanks a lot!! very simple answer :) I wish you all the best.And thanks for your patient. Btw, can i rate your answer somehow? i am very new at that site and in paraview
Sincerely, Kostas ----- Original Message ----- From: "Mathieu Westphal" <[email protected]> To: "Konstantinos Panagiotou" <[email protected]>, "ParaView" <[email protected]> Sent: Wednesday, July 27, 2016 12:48:41 AM Subject: Re: [Paraview] plume tracking-trajectory Hello You can use the filter ParticleToPathLines on the TableToPoints filter to visualize the path of your particle. Mathieu Westphal On Tue, Jul 26, 2016 at 5:39 PM, Konstantinos Panagiotou < [email protected] > wrote: I hope this time is ok the vtk file is the flow solution,the csv file is the particle data kostas From: "Mathieu Westphal" < [email protected] > To: "Konstantinos Panagiotou" < [email protected] > Cc: "ParaView" < [email protected] > Sent: Wednesday, July 27, 2016 12:24:04 AM Subject: Re: [Paraview] plume tracking-trajectory I am unable to load your pvsm. Please provide all the data needed by your pvsm in order for me to load it. Mathieu Westphal On Tue, Jul 26, 2016 at 5:03 PM, Konstantinos Panagiotou < [email protected] > wrote: <blockquote> hello i have loaded the csv data and a vtk file,a cube basicly, in which the flow solution is stored From: "Mathieu Westphal" < [email protected] > To: "Konstantinos Panagiotou" < [email protected] > Cc: "ParaView" < [email protected] > Sent: Tuesday, July 26, 2016 11:53:41 PM Subject: Re: [Paraview] plume tracking-trajectory Your data does not seem to be correctly formated. Can you send me an associated pvsm file ? Mathieu Westphal On Tue, Jul 26, 2016 at 4:08 PM, Konstantinos Panagiotou < [email protected] > wrote: <blockquote> Dear Mathieu, i have installed cmake and qt in order to use cmake command to convert to .vtp. However,i need to add some additional packages which i am not familiar with. So, instead of converting to .vtp, i am sending you in zip form two files with different formats, vtk and csv respectively, files which i have loaded to paraview and being able to animate them using glyph. they are few KB each, it is the minimum i could do in order to keep the example as simple as possible for possible extension later on. Sincerely, Kostas From: "Mathieu Westphal" < [email protected] > To: "Konstantinos Panagiotou" < [email protected] >, "ParaView" < [email protected] > Sent: Tuesday, July 26, 2016 8:06:16 PM Subject: Re: [Paraview] plume tracking-trajectory Please keep the ml in the loop so everyone can follow this. Please open you csv data, save it as a .vtp file and send it to me (if it's not too big) Regards, Mathieu Westphal On Tue, Jul 26, 2016 at 12:55 PM, Konstantinos Panagiotou < [email protected] > wrote: <blockquote> Hello Mathieu, i have applied the Temporal ParticlePath filter,however i havent seen any change. I mean, when i apply glyph to the input data, i can activate this filter and apply it to the input data,either vtk or csv point data. However, i havent managed yet to see trajectories of the particles, only the position of the particle or particles at a specific time step.I have searched and I have seen in other posts in the forum referring to the same issue, that the operation interface of the newest vesrion of paraview is different than the previous ones for the specific function. Can you guide me pls if you can? :) Thanks again, Kostas From: "Mathieu Westphal" < [email protected] > To: "Konstantinos Panagiotou" < [email protected] > Cc: "ParaView" < [email protected] > Sent: Thursday, July 21, 2016 6:16:27 PM Subject: Re: [Paraview] plume tracking-trajectory Hello You should have a look to ParticlePath filter. Regards Mathieu Westphal On Thu, Jul 21, 2016 at 10:38 AM, Konstantinos Panagiotou < [email protected] > wrote: <blockquote> Hi, i am having a problem on plotting the trajectory of a single particle at the top of a flow solution. Particularly, i have a csv file, which is named text0000.csv,inside which i have 4 columns, x,y,z, t.in addition, i have additional files text0001.csv,text0002.csv etc, with one row each( variables' values at each time step) When i load them to the paraview project,i have no problem on performing the animation.However, i also want to have particle's trajectory while it evolves, that is,having lines connecting the updated points with the previous ones. But i havent managed to do that yet. I have installed a paraview version 5.0.1. pls help me,what i should do? _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview </blockquote> </blockquote> </blockquote> </blockquote>
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
