> Use the (-) dash to replace the underscore (_) in a complex net name, > e.g., > don't use FWD_MUX_CON but instead use FWD-MUX-CON > Just a note, The (-) dash is used in the Protel Net list to seperate part and pin designations. I've had problems before because Protel thinks the net name has ended when it see's a (-). I don't use them anymore. Ed > Use this convention on symbols and all net names. I can guarantee that > you > will NEVER print a Protel (or other) schematic, and/or make copies of > same, > that will have signal name readability problems. NEVER. No lines on top > of > net names, and no lines at the bottom of net names. It is also true that > old habits about these things are hard to break. > > Hope this helps! Cheers! > ----------------------------------------- > John R. Lemburg, Sr. Hardware Engineer > Avistar Systems, Inc., Madison Building > 15851 Dallas Parkway, Suite #600 > Addison, TX 75001 > Direct 972-371-5708, Main 972-361-6226 > Fax 972-687-7014, [EMAIL PROTECTED] > ----------------------------------------- > > > -----Original Message----- > From: TSListServer [mailto:[EMAIL PROTECTED]]On > Behalf Of Drew Lundsten > Sent: Wednesday, February 07, 2001 9:56 PM > To: Multiple recipients of list proteledausers > Subject: [PROTEL EDA USERS]: PDF and/or Postscript generation with > "over-bars"? > > > > When we print schematics to .pdf using Acrobat Distiller or PDFWriter, > or to a generic Postscript printer (ours is a HP Laserjet 4050N), > "over-bar" symbols often disappear from a pin or net name and turn into > a much longer bar or line segment somewhere else on the same schematic > page. The result is that with a large page full of active-low signals, > the spurious over-bars make reading the schematic impossible - they look > like wire segments. > > The installation in question is a P3-550/192M/Win2K/P99SE/SP5, and just > now confirmed with SP6. Protel tech support also confirmed the problem > on a sample schematic today, according to one of our engineers; it has > come up several times on various schematics of various sizes. > > Has anyone else had printing problems with over-bars and if so, are > there any known solutions? My inclination is to always stick with a > leading - or # for active-low signals, but support and revision of > legacy designs is still a problem. > > Thanks in advance, > > Drew > > > > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * > * This message sent by: PROTEL EDA USERS MAILING LIST > * > * Use the "reply" command in your email program to > * respond to this message. > * > * To unsubscribe from this mailing list use the form at > * the Association web site. You will need to give the same > * email address you originally used to subscribe (do not > * give an alias unless it was used to subscribe). > * > * Visit http://www.techservinc.com/protelusers/subscrib.html > * to unsubscribe or to subscribe a new email address. > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * > > > > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * > * This message sent by: PROTEL EDA USERS MAILING LIST > * > * Use the "reply" command in your email program to > * respond to this message. > * > * To unsubscribe from this mailing list use the form at > * the Association web site. You will need to give the same > * email address you originally used to subscribe (do not > * give an alias unless it was used to subscribe). > * > * Visit http://www.techservinc.com/protelusers/subscrib.html > * to unsubscribe or to subscribe a new email address. > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * This message sent by: PROTEL EDA USERS MAILING LIST * * Use the "reply" command in your email program to * respond to this message. * * To unsubscribe from this mailing list use the form at * the Association web site. You will need to give the same * email address you originally used to subscribe (do not * give an alias unless it was used to subscribe). * * Visit http://www.techservinc.com/protelusers/subscrib.html * to unsubscribe or to subscribe a new email address. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ________________________________________________________ To leave the EDAFORUM discussion list, send a email with 'leave edaforum' in the body to '[EMAIL PROTECTED]' More Information : http://www.dolist.net