Everything is relative cost sounded good. One has to factor in all of the major considerations.
Ricky Prevatte LMBT1154 > On Jul 15, 2015, at 6:22 PM, Christopher-Mark Gilland <[email protected]> > wrote: > > Actually, I never used Automation. I just let the compressor/E Q, and the > manual clip gain I did do the trick. Plus, I manually panned out some of the > instruments. this way, not everything was dead smack center. > > Chris. > > ----- Original Message ----- > From: Ricky Prevatte > To: [email protected] > Sent: Wednesday, July 15, 2015 2:06 PM > Subject: Re: OK, here's the final mix. > > How much automation did you do before you ever used compression? The last mix > was great. I am old and my theories are different than most the less of > anything for me the better. I have a little more personal interest as Randy > Travis's a friend. > > Ricky Prevatte LMBT1154 > >> On Jul 15, 2015, at 11:03 AM, Christopher-Mark Gilland >> <[email protected]> wrote: >> >> That actually does make sense. Then, you'd use your attack and release to >> then kind a fine tune, but the threshold is gonna be the most important >> thing. I did do another mix on this, which I'll upload a bounce of in a >> bit, so you can see if it's better. I actually got 2 more second opinions, >> and both them feel this third mix I did is perfect! I even not only worked >> a bit with the compression, but I also did a little clip gain reduction on a >> few parts that I felt needed just a notch down. >> >> Chris. >> >> ----- Original Message ----- >> From: Poppa Bear >> To: [email protected] >> Sent: Tuesday, July 14, 2015 11:59 PM >> Subject: RE: OK, here's the final mix. >> >> That’s a good starting place much of the time. >> From: [email protected] [mailto:[email protected]] On Behalf >> Of Christopher-Mark Gilland >> Sent: Tuesday, July 14, 2015 12:39 PM >> To: [email protected] >> Subject: Re: OK, here's the final mix. >> Aa, which means, I'd need to lower! the threshold, so it reacts sooner, at a >> lower level, therefore letting some of the louder dynamics get a bit more >> peeked down. I get it. >> OK. >> Chris. >> ----- Original Message ----- >> From: Chris Smart >> To: [email protected] >> Sent: Tuesday, July 14, 2015 10:30 AM >> Subject: Re: OK, here's the final mix. >> more compression would mean higher ratio or adjusting the threshold so it >> acts on more of the signal. >> >> At 02:36 AM 7/14/2015, you wrote: >> >> OK, can you elaborate a bit more on what you mean by adding more >> compression? What settings might you tweat a bit? Is there any place where >> you could direct me to in the song to listen to so maybe I could hear >> specifically what you mean? Like can you give me a phraise reference where >> it sounds like the compression needs to be just a tad more? >> >> Chris. >> >> ----- Original Message ----- >> From: Poppa Bear >> To: [email protected] >> Sent: Tuesday, July 14, 2015 1:57 AM >> Subject: RE: OK, here's the final mix. >> >> Hey Chris, this sounds like one of your better recordings. I like the >> levels, and the only thing I would add is some more compression to tame some >> of the dynamics in the vocals and a little reverb to gel things together a >> little more and add some depth. >> >> Overall, your coming along. >> >> >> >> >> From: [email protected] [ mailto:[email protected]] On >> Behalf Of Christopher-Mark Gilland >> Sent: Monday, July 13, 2015 9:02 PM >> To: [email protected] >> Subject: OK, here's the final mix. >> >> >> >> >> I still have the session if you all think I need to improve something, but >> here's what I got so far. >> >> >> >> >> https://www.sendspace.com/pro/dl/f3mexq >> >> >> >> >> Note, this isn't the session. this is just the bounced .wav file. If you >> want the session though, let me know, as I've made a ton of changes from the >> one I sent earlier. I'll have to reupload, but if you all have a high >> enough demand for it, I'll see that you get it. >> >> >> >> >> Chris. >> >> >> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> --- Learn to meditate and train your brain with Muse, the first lab-grade >> EEG biofeedback headband for home use! >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> -- >> You received this message because you are subscribed to the Google Groups >> "Pro Tools Accessibility" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. > -- > You received this message because you are subscribed to the Google Groups > "Pro Tools Accessibility" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- > You received this message because you are subscribed to the Google Groups > "Pro Tools Accessibility" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Pro Tools Accessibility" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
