Well, the thinning of data is set in the Preferences dialog. By default, it's set to some degree of thinning. You can adjust it a bit more or less. I'm sure the default setting will do fine. HTH, Slau
> On Mar 29, 2019, at 6:09 PM, Christopher Gilland <clgillan...@gmail.com> > wrote: > > Slau, > > > You always give such detailed, and such wonderful information that is so easy > to understand! Thank you! This is absolutely excellent! Might I ask one > question in regards to doing this type fade out with automation? > > > I agree entirely that it would be so much easier with a surface, but for > those like me who don't have one on hand, here's my question. Each time you > VO+down arrow on that master volume fader, it's writing one event of > automation. I remember there being a way to smoothen that out so that it > sounds more natural, and so it takes all those individual written events and > consolidates them into one. How do I do that? I've honestly forgotten. > > > Chris. > > > On 03/29/2019 12:04 PM, Slau Halatyn wrote: >> Get your transport to a few seconds before where you want the fade to begin. >> Press Command Num Pad 4 to bring up the Automation dialog. Make sure >> automation isn't bypassed. Make sure Volume is selected for automation. >> Close the dialog with the same shortcut. Make sure your master track's >> automation mode is set to Write. Focus and interact with the master track's >> volume fader. Engage the transport. Press Vo Down Arrow to make the fade. >> Note that you'll be moving in half a decibel increments so you'll be >> pressing the down arrow quite a lot. When you're done, press the Space Bar. >> It's quite a bit easier with a control surface. >> HTH, >> Slau >> >> >>> On Mar 29, 2019, at 11:46 AM, Alex Coleman <musicbyalexcole...@gmail.com> >>> wrote: >>> >>> Thank you for the response. I was interested in placing automation on the >>> master Fater, but cannot quite figure out how to make it happen. >>> >>> Sent from my iPhone >>> >>>> On Mar 29, 2019, at 10:08 AM, Martin (Punky) Sopart <m...@cakewalker.de> >>>> wrote: >>>> >>>> Hi! >>>> >>>> If you definitely want to use the master fader, you have to do the >>>> fade-out by automation. >>>> >>>> Another way is to bounce all required tracks to a new e.g. stereo track. >>>> After that move the insertion point to that location where the fade should >>>> start and press Control+G. >>>> This will create a fade-out according tot he existing fade settings in the >>>> Pro Tools preferences. >>>> >>>> Best! / Martin >>>>> -----Original Message----- >>>>> From: ptaccess@googlegroups.com [mailto:ptaccess@googlegroups.com] >>>>> On Behalf Of Alex Coleman >>>>> Sent: Friday, March 29, 2019 2:58 PM >>>>> To: ptaccess@googlegroups.com >>>>> Subject: Placing a fade out on the master Fater >>>>> >>>>> Does anyone have any advice or suggestions on how to place a fade out on >>>>> the master Fater? Thanks for any feedback you can provide. >>>>> I am running ProTools 2018.10. >>>>> >>>>> Sent from my iPhone >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google Groups >>>>> "Pro Tools Accessibility" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send an >>>>> email to ptaccess+unsubscr...@googlegroups.com. >>>>> For more options, visit https://groups.google.com/d/optout. >>>> -- >>>> You received this message because you are subscribed to the Google Groups >>>> "Pro Tools Accessibility" group. >>>> To unsubscribe from this group and stop receiving emails from it, send an >>>> email to ptaccess+unsubscr...@googlegroups.com. >>>> For more options, visit https://groups.google.com/d/optout. >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "Pro Tools Accessibility" group. >>> To unsubscribe from this group and stop receiving emails from it, send an >>> email to ptaccess+unsubscr...@googlegroups.com. >>> For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Pro Tools Accessibility" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to ptaccess+unsubscr...@googlegroups.com. > For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Pro Tools Accessibility" group. To unsubscribe from this group and stop receiving emails from it, send an email to ptaccess+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
