Slow electric windows - some guides expand with age and so have a tendency to 
grip the glass more firmly - run the windows up and down with manual assistance 
a few times whilst applying pressure to one side then the other to loosen off 
the runners.  Some people advocate applying French chalk to the runners (if you 
can find it!); today the nearest is probably talcum powder.  The comment about 
seal pressure is also highly relevant.

Constant squeak from the cam belt area - this indicates a misalignment causing 
a belt to slide to one side of one of the shouldered pulleys and rub.  
Generally this can generally be traced to an angular misalignment of the idler 
pulley assembly, possibly due to paint or dirt between the bracket and the 
engine crankcase - it only needs ~1/10'th of a mm to cause this.  On mine it 
was uneven paint on the crankcase in the region of the power steering idler 
bracket, which was a later addition to the engine - remove the paint and the 
squeak disappeared.

Hamish


  ----- Original Message ----- 
  From: PeteM 
  To: Quantum Owners Group 
  Sent: Monday, September 07, 2009 6:50 PM
  Subject: [Quantum Owners] Re: Refurb my H4





  On 7 Sep, 11:11, Stuart Carvell <[email protected]> wrote:
  >
  > Other problems
  >
  > Slow electic windows especially when they are both used at the same time 
(not sure if its normal?)

  Mine are slow too.  I'd put it down to their age (even the youngest
  donor parts will be nearly 15 years old now) combined with keeping the
  pressure against the door seals.

  > Constant squeek from cam belt area of engine, despite a number of new 
pullies belts etc (The car has been to three garages for this still no fix)

  That might be the auxiliary drive belt that runs round the power
  steering, water pump and alternator.

  > Slightly vague steering, suspect universal joint (Problems with gaining a 
replacement Ford sourced the replacement for the donor but when it came it was 
incorrect. Not sure if the PAS UJ/steering column is different?)

  Yes it is

  > Bushes I would like to replace them with Poly but think i personally would 
struggle.

  If it's your daily driver then do you really want the harshness of
  polybushes?  I asked on here a few months ago and based on the advice
  I'm in the middle of changing the rear axle mounting bushes for a new
  set of standard Ford bushes.  If I'd known how long it would take me
  to do it then I might have popped it down to the local garage rather
  than spending hours in B&Q trying to find some tube with an internal
  diameter of 58mm .....

  > Creeking drivers seat

  Do you have the earlier (seatbelts buckle on a separate stalk) or
  later (seatbelt buckle attached to the subframe) subframes on the
  seats?  I've got the later ones normally fitted to a mk3.5 (wingback
  seats) and had a really bad squeak from the drivers seat to the extent
  that I ended up buying another set of mk3.5 seats for the subframes.
  I think that the problem is where the seatbelt buckle mounts onto the
  subframe - if you can tighten the torx bolt up it might help.


  Pete
  


--~--~---------~--~----~------------~-------~--~----~
  You received this message because you are subscribed to the Google Groups 
"Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to 
[email protected]
For more options, visit this group at 
http://groups.google.com/group/quantumowners?hl=en

IMPORTANT NOTE: All information presented herewith is provided on an "As Is" 
basis, without warranty or the implication thereof. Neither the Quantum Owners 
Club nor the individuals associated with the Quantum Owners Club or in the 
preparation of the above information shall have any liability to any person or 
entity with respect to liability, loss, or damage caused or alleged to be 
caused directly or indirectly by the instructions contained within this or 
related message(s).
-~----------~----~----~----~------~----~------~--~---

Reply via email to