Hi, I'm definitely running NX-OS however running the debug under cisco-xr gives me better results, with the exception that the end of run isn't found
$ rancid -t cisco-xr -d host.xx. loadtype: device type cisco-xr loadtype: found device type cisco-xr in /usr/local/rancid/etc/rancid.types.base executing clogin -t 90 -c"terminal no-timestamp;terminal exec prompt no-timestamp;admin show version;admin show install summary;admin show license udi;admin show license;admin show variables boot;admin show hw-module fpd location all;show redundancy secondary;show install active;admin show env all;dir /all nvram:;dir /all bootflash:;dir /all compactflash:;dir /all compactflasha:;dir /all slot0:;dir /all disk0:;dir /all disk0a:;dir /all slot1:;dir /all disk1:;dir /all disk1a:;dir /all slot2:;dir /all disk2:;dir /all harddisk:;dir /all harddiska:;dir /all harddiskb:;show controllers;admin show diag;admin show inventory raw;show vlan;show debug;show rpl maximum;admin show running;show running-config" host.xx. PROMPT MATCH: host.xx# HIT COMMAND:host.xx# terminal no-timestamp In RunCommand: host.xx# terminal no-timestamp HIT COMMAND:host.xx# terminal exec prompt no-timestamp In RunCommand: host.xx# terminal exec prompt no-timestamp HIT COMMAND:host.xx# admin show version In ShowVersion: host.xx# admin show version HIT COMMAND:host.xx# admin show install summary In ShowInstallSummary: host.xx# admin show install summary HIT COMMAND:host.xx# admin show license u In ShowLicense: host.xx# admin show license udi HIT COMMAND:host.xx# admin show license In ShowLicense: host.xx# admin show license HIT COMMAND:host.xx# admin show variables boot In ShowBootVar: host.xx# admin show variables boot HIT COMMAND:host.xx# admin show hw-module fpd location all In ShowRunning: host.xx# admin show hw-module fpd location all HIT COMMAND:host.xx# show redundancy secondary In ShowRedundancy: host.xx# show redundancy secondary HIT COMMAND:host.xx# show install active In ShowInstallActive: host.xx# show install active HIT COMMAND:host.xx# admin show env all In ShowEnv: host.xx# admin show env all HIT COMMAND:host.xx# dir /all nvram: In DirSlotN: host.xx# dir /all nvram: HIT COMMAND:host.xx# dir /all bootflash: In DirSlotN: host.xx# dir /all bootflash: HIT COMMAND:host.xx# dir /all compactflash: In DirSlotN: host.xx# dir /all compactflash: HIT COMMAND:host.xx# dir /all compactflasha: In DirSlotN: host.xx# dir /all compactflasha: HIT COMMAND:host.xx# dir /all slot0: In DirSlotN: host.xx# dir /all slot0: HIT COMMAND:host.xx# dir /all disk0: In DirSlotN: host.xx# dir /all disk0: HIT COMMAND:host.xx# dir /all disk0a: In DirSlotN: host.xx# dir /all disk0a: HIT COMMAND:host.xx# dir /all slot1: In DirSlotN: host.xx# dir /all slot1: HIT COMMAND:host.xx# dir /all disk1: In DirSlotN: host.xx# dir /all disk1: HIT COMMAND:host.xx# dir /all disk1a: In DirSlotN: host.xx# dir /all disk1a: HIT COMMAND:host.xx# dir /all slot2: In DirSlotN: host.xx# dir /all slot2: HIT COMMAND:host.xx# dir /all disk2: In DirSlotN: host.xx# dir /all disk2: HIT COMMAND:host.xx# dir /all harddisk: In DirSlotN: host.xx# dir /all harddisk: HIT COMMAND:host.xx# dir /all harddiska: In DirSlotN: host.xx# dir /all harddiska: HIT COMMAND:host.xx# dir /all harddiskb: In DirSlotN: host.xx# dir /all harddiskb: HIT COMMAND:host.xx# show controllers In ShowContAll: host.xx# show controllers HIT COMMAND:host.xx# admin show diag In ShowDiag: host.xx# admin show diag HIT COMMAND:host.xx# admin show inventory raw In ShowInventory: host.xx# admin show inventory raw HIT COMMAND:host.xx# show vlan In ShowVLAN: host.xx# show vlan HIT COMMAND:host.xx# show debug In ShowDebug: host.xx# show debug HIT COMMAND:host.xx# show rpl maximum In ShowRPL: host.xx# show rpl maximum HIT COMMAND:host.xx# admin show running In ShowRunning: host.xx# admin show running HIT COMMAND:host.xx# show running-config In WriteTerm: host.xx# show running-config host.xx.: End of run not found host.xx.: found_end is false On Thu, Feb 8, 2018 at 1:33 PM, Piegorsch, Weylin William <wey...@bu.edu> wrote: > Doesn’t ASR9k run IOS XR (rancid type “ios-xr”)? I didn’t think it > supported NX-OS. I’ve only seen NX-OS on Nexus (including N9k), MDS, and > UCS devices. > > weylin > > > > *From: *Pico Leto <picoleto...@gmail.com> > *Date: *Wednesday, February 7, 2018 at 2:05 PM > *To: *<rancid-discuss@shrubbery.net> > *Subject: *[rancid] Role Privileges for Nexus 9k > > > > Hi, > > > > I seem to be having some troubles backing up my configs for a ASR9k > (C93108TC-EX) running NXOS 7.0.3.I4.4. My current version of rancid is 3.7 > > > > I thought I created the correct role for rancid to run under however my > debug seems to end after 'system redundancy status'. The command is > actually available however you have to be in config term mode to see the > output. > > > > Role: rancid > > Description: rancid restricted access > > Vlan policy: permit (default) > > Interface policy: permit (default) > > Vrf policy: permit (default) > > ------------------------------------------------------------------- > > Rule Perm Type Scope Entity > > ------------------------------------------------------------------- > > 4 permit command dir * > > 3 permit command show * > > 2 permit command terminal * > > 1 permit command show running-config > > > > Debug: > > > > rancid -t cisco-nx -d host.xx.xx > > loadtype: device type cisco-nx > > loadtype: found device type cisco-nx in /usr/local/rancid/etc/rancid. > types.base > > executing clogin -t 90 -c"term no monitor-force;show version;show version > build-info all;show license;show license usage;show license > host.xx.xx-id;show system redundancy status;show environment clock;show > environment fan;show environment fex all fan;show environment > temperature;show environment power;show boot;dir bootflash:;dir debug:;dir > logflash:;dir slot0:;dir usb1:;dir usb2:;dir volatile:;show module;show > module xbar;show inventory;show vtp status;show vlan;show debug;show cores > vdc-all;show processes log vdc-all;show module fex;show fex;show > running-config" host.xx.xx > > PROMPT MATCH: host.xx# > > HIT COMMAND:host.xx# term no monitor-force > > In RunCommand: host.xx# term no monitor-force > > HIT COMMAND:host.xx# show version > > In ShowVersion: host.xx# show version > > TYPE = NXOS > > HIT COMMAND:host.xx# show version build-info all > > In ShowVersionBuild: host.xx# show version build-info all > > HIT COMMAND:host.xx# show license > > In ShowLicense: host.xx# show license > > HIT COMMAND:host.xx# show license usage > > In ShowLicense: host.xx# show license usage > > HIT COMMAND:host.xx# show license host.xx.xx-id > > In ShowLicense: host.xx# show license host.xx.xx-id > > HIT COMMAND:host.xx# show system redundancy status > > In ShowRedundancy: host.xx# show system redundancy status > > host.xx.xx: show system redundancy status failed: -1 > > host.xx.xx: missed cmd(s): show environment clock, show environment fan, > show environment fex all fan, show environment temperature, show > environment power, show boot, dir bootflash:, dir debug:, dir logflash:, > dir slot0:, dir usb1:, dir usb2:, dir volatile:, show module, show module > xbar, show inventory, show vtp status, show vlan, show debug, show cores > vdc-all, show processes log vdc-all, show module fex, show fex > > host.xx.xx: End of run not found > > host.xx.xx: clean_run is false > > host.xx.xx: found_end is false >
_______________________________________________ Rancid-discuss mailing list Rancid-discuss@shrubbery.net http://www.shrubbery.net/mailman/listinfo/rancid-discuss