Hi Razzak
01. Check for the correct RBG7.1 installation files, such as:
RBG7.EXE in C:\RBTI\RBG7 7/15/2004 19:07
RBENGIN1.MSG in C:\Windows or \WinNT 7/15/2004 19:07
RBENGIN2.MSG in C:\Windows or \WinNT same
RBENGIN3.MSG in C:\Windows or \WinNT same
I also have
RB701.MSG 10/14/2003 7:07
RB702.MSG same
RB703.MSG same
RBENGINE.DLL in C:\Windows\System32 or \WinNT\System32
7/15/2004 19:07
I also have
RB70_32.dll 10/14/2003 7:07
RB70INS.dll same
Are there any duplicate files in other directory?
NO Dups
Is there anything else I should try?
Thanks
Marc
> 02. What is the date and time on those files?
>
> Hope that helps!
>
> Very Best R:egards,
>
> Razzak.
>
> At 05:26 PM 7/27/2004 -0500, you wrote:
>
> >Hi Razzak
> >
> >I followed the steps and when I tried to open a table this
> >is the error I got. Also, below is a list of SYS% at the R>
> >Very Strange.
> >After I get this error if I disc then con I do not get the error,
> >but if I quit RBase then con and try to open the table the error
> >is back.
> >Even stranger.
> >
> >What else should I try?
> >thanks
> >Marc
> >
> >---------------------------
> >Error
> >---------------------------
> >SYS_LAYOUTS3 Table Does Not Exist!
> >---------------------------
> >OK
> >---------------------------
> >
> > Name Columns Rows Comments
> >
> > SYS_LAYOUTS3 3 3
> > SYS_MERGE 6 0
> > SYS_PROCEDURES 10 0
> > SYS_PROC_COLS 10 0
> > SYS_PROC_MODS 8 0
> > SYS_REPORTS 3 0
> > SYS_REPORTS2 4 121
> > SYS_REPORTS3 5 121
> >
> >
> >----- Original Message -----
> >From: "A. Razzak Memon" <[EMAIL PROTECTED]>
> >To: "RBG7-L Mailing List" <[EMAIL PROTECTED]>
> >Sent: Tuesday, July 27, 2004 4:55 PM
> >Subject: [RBG7-L] - Re: SYS_layout3
> >
> >
> > >
> > > Step 02 should read as following:
> > >
> > > 02. At the R> Prompt:
> > > SET MULTI OFF
> > > CONNECT dbname
> > > UPGRADE -- that will take care of any missing required table(s).
> > >
> > > Razzak.
> > >
> > >
> > > At 04:30 PM 7/27/2004 -0500, Marc Schulter wrote:
> > >
> > > >I keep getting an error about can't find sys_layout 3 table.
> > > >If I do List Sys% I can the table.
> > > >
> > > >I remember something about this a few months ago but can't
> > > >find the post.
> > >
> > >
> > > Marc,
> > >
> > > Most likely, you have not followed the instructions to UPGRADE
> > > your database from 6.x.
> > >
> > > So, here's what you have to do:
> > >
> > > 01. Start RBG7.1
> > >
> > > 02. At the R> Prompt:
> > > SET MULTI ON
> > > CONNECT dbname
> > > UPGRADE -- that will take care of any missing required table(s).
> > >
> > > 03. LIST SYS%
> > >
> > > The following SYSTEM tables will be added:
> > > SYS_FORMS3
> > > SYS_LABELS3
> > > SYS_LAYOUTS3
> > > SYS_MERGE
> > > SYS_REPORTS3
> > >
> > > 04. DISCONNECT
> > >
> > > 05. SET MULTI ON
> > >
> > > 06. CONNECT dbname
> > >
> > > Have fun!
> > >
> > > Very Best R:egards,
> > >
> > > Razzak.
> > >
> > >
>
>
