Michael,
Since I have not received a response from my first offer,
send me your info direct to my email address. jplily@yahoo. I also have the
9 to 1 gear reduction transmission assembly if you want it. I can send you
a pic of the setup. Once I have your address, I'll get the shipping
charges and make sure the price is good for you.
John
l
On Friday, March 21, 2014 8:11:03 PM UTC-4, Michael Butts wrote:
>
> Not to squat on your offer to Hessel... but... I will happily take you
> up on that if he does not. I just procured my first tank component. 4&6awg
> high strand count silicone jacketed wire. These pictures are of the 4awg.
> Super cheap (relatively) on eBay. I got 12ft of each shipped for $47:)
> Mike Butts
> [image: image.jpeg][image: image.jpeg][image: image.jpeg]
>
>
> On Mar 21, 2014, at 7:28 PM, jvragu47 <[email protected] <javascript:>>
> wrote:
>
> If you truly need EV Warriors, I have 2 sitting in my basement from the
> old T-12. Be glad to send them for the cost of shipping. Have the mounting
> brackets and leads .Let me know and we'll figure it out.
>
> John P.
>
>
> On Thursday, March 20, 2014 9:30:31 PM UTC-4, TyngTech wrote:
>>
>> Hey Hessel, aka Dutch Guy,
>>
>> The EV Warriors are hard to find nowadays. Most current builders are
>> using geared scooter motors such as:
>>
>> http://www.fieldofarmortanks.com/product_p/foa-my1018.htm
>>
>> http://tncscooters.com/index.php?route=product/product&path=52_55&product_id=55
>>
>>
>> Steve
>>
>>
>> On Thursday, March 20, 2014 9:52:03 AM UTC-4, HSGameplays wrote:
>>>
>>> Hey Steve,
>>>
>>> Dutch guy tuning in here. I came to this page searching for an engine
>>> for our school project: walking robot carrying a heavy load (in our case,
>>> crates of beer). I noticed the link you put up on this page about the
>>> EV-warrior engine, but when I came to that page the engine was
>>> discontinued. Do you happen to know of any engines that can replace this
>>> niche nowadays, or are comparable to the older engines?
>>>
>>> Kind regards,
>>> Hessel
>>>
>>> Op woensdag 12 oktober 2011 13:03:36 UTC+2 schreef TyngTech:
>>>>
>>>> 10mph at only .6hp is probably a bit unrealistic. My tank (T040) when
>>>> first built was measured at 8+mph on flat pavement. It's weight is in the
>>>> range your talking for your vehicle and it's running two 950w motors at
>>>> 24v
>>>> (3hp) with a commercial motor controller. With 350w motors we are seeing
>>>> speeds in the 3 to 5mph range. You can probably gear your vehilcle to get
>>>> to 10mph but it will have little torque to do neutral turns on anything
>>>> other than pavement.
>>>>
>>>> Something else to consider is that a 100 pound model running at 10mph
>>>> with home-brew controllers and electronics can be a dangerous thing.
>>>>
>>>> Steve
>>>>
>>>> --
> --
> You are currently subscribed to the "R/C Tank Combat" group.
> To post a message, send email to [email protected] <javascript:>
> To unsubscribe, send email to [email protected]<javascript:>
> Visit the group at http://groups.google.com/group/rctankcombat
>
> ---
> You received this message because you are subscribed to the Google Groups
> "R/C Tank Combat" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected] <javascript:>.
> For more options, visit https://groups.google.com/d/optout.
>
>
--
--
You are currently subscribed to the "R/C Tank Combat" group.
To post a message, send email to [email protected]
To unsubscribe, send email to [email protected]
Visit the group at http://groups.google.com/group/rctankcombat
---
You received this message because you are subscribed to the Google Groups "R/C
Tank Combat" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
