Jay, thanks yes that is correct, it was a jumper to allow the FNDC to work. I had no trouble connecting a Mate3s to the FM100-AFCI.
Brad On Mon, Oct 19, 2020 at 12:37 PM Jay <[email protected]> wrote: > On page 71 there is a small note about hooking up a FNDC without an > inverter. > > It might be what Brad was mentioning. > > Jay > > > On Oct 19, 2020, at 12:48 PM, Dan Fink <[email protected]> wrote: > >  > Maybe Brad is referring to the GFDI jumper or the RSS jumper? I don't know > of a jumper to activate comms with the Mate 3S. > > The former is for bonding and you remove it if you use an external GFDI, > like a Midnite GFCI in a Midnite MNDC enclosure. It's the little black wire > with 2 red spade connectors under the terminal block. > > The RSS jumper you have to make out of a scrap of wire to DIS-able the > Flexmax 100 internal RSS trigger. It goes between the yellow and purple > terminal blocks. If you don't install it, the CC assumes the RSS has been > activated. I love this one for my students, when their homework before lab > class is to *thoroughly* read the instructions and make notes! I can easily > tell if they actually did LOL. > > Dan Fink > Owner, Buckville Energy Consulting > NABCEP Certified PV System Inspector > IREC Certified Instructor™ for: > ~ PV Installation Professional > ~ Small Wind Installer > NABCEP Registered Continuing Education Providers > d <[email protected]>[email protected] > 970-672-4342 > > > On Sat, Oct 17, 2020 at 8:11 AM Bradley Bassett <[email protected]> > wrote: > >> I think there is a jumper in the FM100 that will allow the Mate3s to >> communicate with it. I don't remember off hand where it is and am not at a >> computer with that info, but maybe this will prompt a look at the manual to >> see if they mention it. >> >> Brad >> >> >> _______________________________________________ > List sponsored by Redwood Alliance > > List Address: [email protected] > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > There are two list archives for searching. When one doesn't work, try the > other: > https://www.mail-archive.com/[email protected]/ > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > List rules & etiquette: > http://www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > http://www.members.re-wrenches.org > > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: [email protected] > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > There are two list archives for searching. When one doesn't work, try the > other: > https://www.mail-archive.com/[email protected]/ > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > List rules & etiquette: > http://www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > http://www.members.re-wrenches.org > >
_______________________________________________ List sponsored by Redwood Alliance List Address: [email protected] Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org There are two list archives for searching. When one doesn't work, try the other: https://www.mail-archive.com/[email protected]/ http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: http://www.re-wrenches.org/etiquette.htm Check out or update participant bios: http://www.members.re-wrenches.org
