Am I missing something or would a change in PL eliminate the other repeater from opening??  I have a similar situation with my repeater and while  we are over a 100 miles apart and a mountain range between, occassionly is we open the PL, we can weakly hear the repeater.  With the PL activated. No interference.  I hope I didn't misread something. 

Mathew Quaife <[EMAIL PROTECTED]> wrote:

All understood there, but the kicker is that my equipment did not interfere
with his repeater, it was a user that is about 70 miles away that got into
one of his remote receiver's. I'm considering the fight of staying my
grounds, and letting the coordinator know that if my system was the cause,
fine, but a user is the culprit, how does that affect me. So to say, any
frequency by regulations is allowed simplex operation, and should one decide
to go off by say 10kc's and talk and if the output of the repeater
interfere's, they should shut the repeater off, because, in this sense of
his offering's, is the last to come, the first to leave. I believe all the
frequencies were simplex before they became duplex.

And answer is that I doubt very seriously that any of the remote receiver
sites here in Indiana are coordinated. How could they be, in fact anywhere,
that only reduces the 100 mile radius they attempt to maintain in
coordinating repeaters. Also, both repeaters used the same 131.8 PL.

Mathew


-----Original Message-----
From: Bob Dengler [mailto:[EMAIL PROTECTED]
Sent: Thursday, February 24, 2005 11:06 AM
To: [email protected]
Subject: Re: [Repeater-Builder] Going got Rough, Forced to change Freq, Need
Answers


At 2/23/2005 03:46 PM, you wrote:


>Well it seems that I am told I have to change frequencies, has it
>that one of my users interferred with the same troublesome repeater
>I've had all along, and now the coordinator says I have to move.
>
>Not sure how well all the equipment will handle the change. Here is
>what I have as equipment, and will it all make it there. We are
>moving from 146.925- to 145.410-, and the expense is the last thing
>I needed right now.
>
>GE MASTR PRO ER41 Receiver

So you'll be dropping the RX about 1.5 MHz. Never had a problem with the
VHF Mastr Pro RX I took down to 144.84.

>Vocom Amp, tuned for 146.925
>and then to top if off, I just got the phasing harness for the DB224
>and it was cut right for 146.925.

The phasing harness is broad enough that you won't see a difference at the
new freq.

>My main transmitter is the (no arguements please), Maggorie HiPro
>transmitter exiting 2 watts to the vocom amp.
>TX RX Duplexers.
>
>How low in frequency will the MASTR Pro go before I loose quality
>sensitivity, right now, it's about .15 uv with a preamp, and
>receives excellent.

It should work fine. In fact, the preamp ahead of it will make any small
degradation in the RX noise figure as a result of the move negligible.

> The vocom amp is model #VVC200-2ref and was
>designed for the 146 Mhz range.
>
>I'm sure the duplexers should not be a problem, other than getting
>them re-tuned. Thoughts!

I don't see any problems other than all the work involved in retuning
everything.


>What anger's me the most about this, is that the repeater owner went
>straight to the coordinator, did not bother to talk with me. I
>changed the PL of the repeater.

Your user may have been getting too good of a signal into the other
repeater's RX. Even with everything CTCSS-protected, a user of one
repeater can still block signals intended for the other system.


>Other sad part is, the user that was getting into their system was
>not getting into the main receiver, but rather a remote site. I
>wonder how tight his receiver really is, and is it a synthesized
>radio, or something of quality.

If it's on-channel, it doesn't matter so long as the remote RX of the other
system is coordinated. A "quality" RX will not reject on-freq. signals
just because they're "intended" for another repeater.

Bob NO6B







Yahoo! Groups Links







--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.4.0 - Release Date: 2/22/2005


--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 266.4.0 - Release Date: 2/22/2005







Yahoo! Groups Links

<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/

<*> To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]

<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/





Do you Yahoo!?
Yahoo! Mail - Easier than ever with enhanced search. Learn more.







Yahoo! Groups Links

Reply via email to