I found the Midland 13-509 conversion instructions on the repeater-builder site along with a manual for the rig. The schematic shows that the RX and TX are quite independant, so the conversion should be straight forward electronically.
The only hard part (for me) will be making all of the mechanical arrangements because the RX and TX must be separated for proper isolation. This isn't overwhelming, I'm just not very good at mechanical stuff. I'm thinking I'll take a left-over 2-U rack mount box I've got and build a partition down the middle and mount the boards on each side of it. I'm thinking this will isolate them well, provide easy access for tuning and maintenance, and provide plenty of aluminum for the PA heatsink (at only 10 watts, it shouldn't require much). If I notice it getting warm, I've got some heatsink material that can be added to the back of the box for additional dissipation. This arrangement should also provide space for ancillary items such as a comspec CTCSS board and possibly the controller (TBD). -- Keith McQueen [EMAIL PROTECTED] 801-224-9460 On 11/7/07, [EMAIL PROTECTED] <[EMAIL PROTECTED]> wrote: > There's lots of articles out there about how to turn one of the 10-watt > Clegg/Midland/Cobra radios into a 220-MHz Repeater.The conversion was > published in at least two TAB books. I don't have them here at the office, > but I do have them at home, but don't remember the exact titles. I can > probably look the TAB Books numbers so you can look on the auction sites, > used book stores, etc. One of them is called something like "220 MHz for the > Radio Amateur", the other one is the big, thick book about Building > Repeaters, I think it was by WA6ITF and WA6ILQ. Also a similar article and > several updates were published in the "220 Notes" Newsletter in the 1990's, > and I believe there was a 73 Magazine article that covered the same project. > > > LJ > > > > > > > > > -----Original Message----- > From: [EMAIL PROTECTED] > Sent: Nov 7, 2007 7:52 AM > To: [email protected] > Subject: Re: Re: [Repeater-Builder] Re: 222 Mhz > > Google found this: > > http://www.ak2o.org/srg/Midland_Linkconversion.html > > The book you are referring to (written by a WA6 I think) is hard to get. > Out of print for sure, but a very handy book. I used to have one but have > misplaced it. > > If anyone has a minimal knowledge of how a receiver and transmitter work, > finds the squelch and the ptt line, audio out, xtal locations, etc.), it > truly is an easy mod. > > Roger W5RD > > >From: DCFluX <[EMAIL PROTECTED] <dcflux%40gmail.com>> > >Date: 2007/11/07 Wed AM 09:42:15 CST > >To: [email protected] <Repeater-Builder%40yahoogroups.com> > >Subject: Re: [Repeater-Builder] Re: 222 Mhz > > > > >Anyone have a write up for the conversion? I remember seeing one in a TAB > book. > > > >On 11/7/07, res1q6fs <[EMAIL PROTECTED] <roger.white%40verizon.net>> > wrote:Ditto here. My 13-509 never suffered any ills for over 20 > years continuous repeater operation and it was an old original brown face > model. No external BPF on front end, an 80 dB null set of duplexers with a > 6 dB antenna on a tower that had 450 MHz, 800 MHz, 900 MHz and 150 MHz > systems running 50 to 100 watts and pagers up to many 100's of watts on > antennas just above the 220 antenna. Never heard a peep of Intermod. Never > used PL. A 0.2 uV max. signal produced a noise free signal out of the > receiver. Roger W5RD ----- Original Message ----- From: [EMAIL > PROTECTED]<no6b%40no6b.com>To: > [email protected] <Repeater-Builder%40yahoogroups.com>Sent: > Wednesday, November 07, 2007 12:23 AM Subject: Re: [Repeater-Builder] > Re: 222 Mhz > > > >At 11/6/2007 15:04, you wrote: > > > >>If you're the type of person who enjoys doing things from the > >>ground up... then the conversions and kits are the way to go if > >>you have the test equipment to get the show on the road once it's > >>built. Otherwise you might consider a turn-key repeater from > >>the Repeater Builder folks, Hamtronics or Maggiore. > >> > >>I would not suggest you go with the Midland 13-509 conversion > >>because after all the work is done... the receiver is just not > >>the best performer. > > > >I completely disagree. I've built a couple of 13-509 systems & continue > to > >service a couple of others. Given what it is, it performs exceptionally > >well. I have one literally sitting in the middle of downtown LA @ 1000 > ft. > >AMSL with nothing but a notch duplexer between the RX & the antenna, & it > > >hears quite well with no IMD. > > > >Bob NO6B > > > > > > > >No virus found in this incoming message. > >Checked by AVG Free Edition. > >Version: 7.5.503 / Virus Database: 269.15.23/1113 - Release Date: > 11/6/2007 10:04 AM > > > > > > > > Roger White > Murphy, Texas > > >

