Salve,
Chestia asta ma innebuneste de o zi si ceva.
Incerc sa fac nat peste conexiune PPPoE ADSL penru setup careia v-am
cerut ajutorul saptamana trecuta.
rc.conf:
gateway_enable="YES"
ifconfig_em0="inet 192.168.1.1 netmask 255.255.255.0"
ifconfig_fxp0="inet 86.35.138.67 netmask 255.255.240.0"
defaultrouter="86.35.128.1"
ppp_enable="YES"
ppp_mode="ddial"
#ppp_nat="YES"
ppp_profile="romtelecom0"
firewall_enable="YES"
firewall_type="SIMPLE"
#firewall_type="OPEN"
firewall_logging="YES"
firewall_quiet="NO"
#natd_enable="YES"
#natd_interface="86.35.138.67"
#natd_flags="-l -log-denied -log-ipfw-denied -m"
Daca folosesc ppp_nat="YES" nu se face NAT - vad pachetele intrand prin
em0 si iesind prin tun0:
Jun 19 12:26:58 mail kernel: ipfw: 50 Count TCP 192.168.1.154:1270
66.163.181.157:21 in via em0
Jun 19 12:26:58 mail kernel: ipfw: 50 Count TCP 192.168.1.154:1270
66.163.181.157:21 out via tun0
si atat, nu se intoarce nimic.
Daca folosesc natd configurat ca mai sus masina isi pierde
conectivitatea prin tun0 (nu mai am nici ping pe ea, nici de pe ea).
Varianta cu ppp -nat ... ar trebui sa merga (sau cel putin mergea acum
niste ani pe o conexiune ppp dial-up).
Varianta cu natd mi s-a spus ca merge si ea.
FreeBSD 6.1-STABLE #1: Fri Jun 9 13:26:04 EEST 2006
# cat /etc/ppp/ppp.conf
default:
set log Phase Chat LCP IPCP CCP tun command
ident user-ppp VERSION (built COMPILATIONDATE)
set device /dev/cuad1
set speed 115200
set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
\"\" AT OK-AT-OK ATE1Q0 OK \\dATDT\\T TIMEOUT 40 CONNECT"
set timeout 180 # 3 minute idle timer (the default)
enable dns # request DNS info (for resolv.conf)
romtelecom0:
set device PPPoE:fxp0
set authname [EMAIL PROTECTED]
set authkey condem
set dial
set login
add default HISADDR
# ifconfig
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_MTU>
inet6 fe80::202:b3ff:fee9:9c4d%fxp0 prefixlen 64 scopeid 0x1
inet 86.35.138.67 netmask 0xfffff000 broadcast 86.35.143.255
ether 00:02:b3:e9:9c:4d
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_MTU>
inet6 fe80::202:b3ff:fee9:9b62%em0 prefixlen 64 scopeid 0x2
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
ether 00:02:b3:e9:9b:62
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492
inet 86.35.138.67 --> 86.35.78.1 netmask 0xffffffff
Opened by PID 1443
Orice idee, working config copy/paste, etc. e extrem de binevenita.
Mersi,
--
IOnut - Un^d^dregistered ;) FreeBSD "user"
"Intellectual Property" is nowhere near as valuable as "Intellect"
BOFH excuse #125:
we just switched to Sprint
signature.asc
Description: PGP signature
