Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On Saturday 06 November 2010 17:48:41 Michael Martin wrote: On 11/06/2010 10:26, Hans Petter Selasky wrote: On Saturday 06 November 2010 17:00:46 Michael Martin wrote: On 11/06/2010 03:31, Hans Petter Selasky wrote: Hi, Can you revert the last patch I sent an apply the attached one? Then repeat the testing like last time. --HPS Here are the results: http://appliedtechnicalknowledge.com/freebsd/usb_30_hub_patch/ I used one drive/port for the testing. da0 not recognized on first boot, but came up after an unplug cable/plug cable. Hi, I will have a closer look into this tomorrow. Does your device work when first recognized? What read/write speeds do you get? --HPS The device doesn't work when I try to import the zfs pool on the drive. The drive shows up in camcontrol ok. I initially exported the zfs file system to avoid attempts to mount it on boot. Once da0 is recognized by the kernel and camcontrol devlist shows it, I try a zpool import on the file system. The zpool import command hangs--sometimes the entire computer locks up, and I hard reboot the computer. I captured the usb logs during the zpool import for you there which captures some zfs i/o errors. Hi, I'm not sure what exacatly the issue is about. Maybe the hardware is incompatible. Is is possible that I could be given SSH and root access to this hardware setup for a limited time to debug this issue? --HPS ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
Hi, Can you revert the last patch I sent an apply the attached one? Then repeat the testing like last time. --HPS I captured several debug outputs here: http://appliedtechnicalknowledge.com/freebsd/usb3-patch-214808/ . Maybe something in these can help. === usb_hub.c == --- usb_hub.c (revision 214808) +++ usb_hub.c (local) @@ -126,9 +126,10 @@ static usb_callback_t uhub_intr_callback; -static void usb_dev_resume_peer(struct usb_device *udev); -static void usb_dev_suspend_peer(struct usb_device *udev); -static uint8_t usb_peer_should_wakeup(struct usb_device *udev); +static void usb_dev_resume_peer(struct usb_device *); +static void usb_dev_suspend_peer(struct usb_device *); +static uint8_t usb_peer_should_wakeup(struct usb_device *); +static uint8_t usb_device_20_compatible(struct usb_device *); static const struct usb_config uhub_config[UHUB_N_TRANSFER] = { @@ -394,13 +395,29 @@ usb_pause_mtx(NULL, USB_MS_TO_TICKS(USB_PORT_POWERUP_DELAY)); - /* reset port, which implies enabling it */ + if (usb_device_20_compatible(udev)) { + /* reset port, which implies enabling it */ + err = usbd_req_reset_port(udev, NULL, portno); + } else { + switch (UPS_PORT_LINK_STATE_GET(sc-sc_st.port_status)) { + case UPS_PORT_LS_U0: + case UPS_PORT_LS_U1: + case UPS_PORT_LS_U2: + case UPS_PORT_LS_U3: + /* no reset needed, link is already UP */ + break; + case UPS_PORT_LS_SS_INA: + /* try to recover link using a warm reset */ + goto error; + default: + /* reset port, which implies enabling it */ + err = usbd_req_reset_port(udev, NULL, portno); + break; + } + } - err = usbd_req_reset_port(udev, NULL, portno); - if (err) { - DPRINTFN(0, port %d reset - failed, error=%s\n, + DPRINTFN(0, port %d reset failed, error=%s\n, portno, usbd_errstr(err)); goto error; } @@ -517,17 +534,43 @@ usb_free_device(child, 0); child = NULL; } - if (err == 0) { + if (err) { + DPRINTFN(0, device problem (%s), + port %u\n, usbd_errstr(err), portno); + goto error_ret; + } + if (usb_device_20_compatible(udev)) { + /* disable the port, if enabled */ if (sc-sc_st.port_status UPS_PORT_ENABLED) { err = usbd_req_clear_port_feature( - sc-sc_udev, NULL, - portno, UHF_PORT_ENABLE); + udev, NULL, portno, UHF_PORT_ENABLE); } + } else { + /* get fresh status again */ + err = uhub_read_port_status(sc, portno); + if (err) + goto error_ret; + + switch (UPS_PORT_LINK_STATE_GET(sc-sc_st.port_status)) { + case UPS_PORT_LS_SS_INA: + /* Try a warm port reset to recover the port. */ + err = usbd_req_warm_reset_port(udev, NULL, portno); + if (err) { + DPRINTF(warm port reset failed.\n); + goto error_ret; + } + break; + default: + /* disable the port, if enabled */ + if (sc-sc_st.port_status UPS_PORT_ENABLED) { + err = usbd_req_clear_port_feature( + udev, NULL, portno, UHF_PORT_ENABLE); + } + break; + } } - if (err) { - DPRINTFN(0, device problem (%s), - disabling port %d\n, usbd_errstr(err), portno); - } + +error_ret: return (err); } ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On Saturday 06 November 2010 17:00:46 Michael Martin wrote: On 11/06/2010 03:31, Hans Petter Selasky wrote: Hi, Can you revert the last patch I sent an apply the attached one? Then repeat the testing like last time. --HPS Here are the results: http://appliedtechnicalknowledge.com/freebsd/usb_30_hub_patch/ I used one drive/port for the testing. da0 not recognized on first boot, but came up after an unplug cable/plug cable. Hi, I will have a closer look into this tomorrow. Does your device work when first recognized? What read/write speeds do you get? --HPS ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On 11/06/2010 10:26, Hans Petter Selasky wrote: On Saturday 06 November 2010 17:00:46 Michael Martin wrote: On 11/06/2010 03:31, Hans Petter Selasky wrote: Hi, Can you revert the last patch I sent an apply the attached one? Then repeat the testing like last time. --HPS Here are the results: http://appliedtechnicalknowledge.com/freebsd/usb_30_hub_patch/ I used one drive/port for the testing. da0 not recognized on first boot, but came up after an unplug cable/plug cable. Hi, I will have a closer look into this tomorrow. Does your device work when first recognized? What read/write speeds do you get? --HPS The device doesn't work when I try to import the zfs pool on the drive. The drive shows up in camcontrol ok. I initially exported the zfs file system to avoid attempts to mount it on boot. Once da0 is recognized by the kernel and camcontrol devlist shows it, I try a zpool import on the file system. The zpool import command hangs--sometimes the entire computer locks up, and I hard reboot the computer. I captured the usb logs during the zpool import for you there which captures some zfs i/o errors. mm ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On 11/04/2010 13:37, Hans Petter Selasky wrote: On Saturday 23 October 2010 15:37:55 Michael Martin wrote: On 10/23/2010 00:23, Hans Petter Selasky wrote: On Saturday 23 October 2010 02:07:59 Michael Martin wrote: On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4:My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001Western Digital iProduct = 0x0002My Book 3.0 iSerialNumber = 0x0003XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2:Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2:Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Output when plugging in the WD 3.0 into the 2.0 port: Oct 21 01:15:20 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub3 Oct 21 01:15:20 gandalf kernel: ugen3.4:Western Digital at usbus3 Oct 21 01:15:20 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 2.10/10.10, addr 4 on usbus3 Oct 21 01:15:20 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:15:21 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:15:28 gandalf kernel: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0 Oct 21 01:15:28 gandalf kernel: da0:WD My Book 3.0 1123 1010 Fixed Direct Access SCSI-4 device Oct 21 01:15:28 gandalf kernel: da0: 40.000MB/s transfers Oct 21 01:15:28 gandalf kernel: da0: 953867MB (1953519616 512 byte sectors: 255H 63S/T 121600C) Output when plugging in 2.0 device into the 3.0 port: Oct 21 01:09:54 gandalf root: Unknown USB device: vendor 0x090c product 0x1000 bus uhub4 Oct 21 01:09:54 gandalf kernel: ugen4.2:USB at usbus4 Oct 21 01:09:54 gandalf kernel: umass1:USB Flash Disk, class 0/0, rev 2.00/11.00, addr 1 on usbus4 Oct 21 01:09:54 gandalf kernel: umass1: SCSI over Bulk-Only; quirks = 0x Oct 21 01:09:55 gandalf kernel: umass1:10:1:-1: Attached to scbus10 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed) Oct 21 01:09:56 gandalf kernel: da1 at umass-sim1 bus 1 scbus10 target 0 lun 0 Oct 21 01:09:56 gandalf kernel: da1:USB Flash Disk
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On Saturday 23 October 2010 15:37:55 Michael Martin wrote: On 10/23/2010 00:23, Hans Petter Selasky wrote: On Saturday 23 October 2010 02:07:59 Michael Martin wrote: On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4:My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001Western Digital iProduct = 0x0002My Book 3.0 iSerialNumber = 0x0003XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2:Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2:Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Output when plugging in the WD 3.0 into the 2.0 port: Oct 21 01:15:20 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub3 Oct 21 01:15:20 gandalf kernel: ugen3.4:Western Digital at usbus3 Oct 21 01:15:20 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 2.10/10.10, addr 4 on usbus3 Oct 21 01:15:20 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:15:21 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:15:28 gandalf kernel: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0 Oct 21 01:15:28 gandalf kernel: da0:WD My Book 3.0 1123 1010 Fixed Direct Access SCSI-4 device Oct 21 01:15:28 gandalf kernel: da0: 40.000MB/s transfers Oct 21 01:15:28 gandalf kernel: da0: 953867MB (1953519616 512 byte sectors: 255H 63S/T 121600C) Output when plugging in 2.0 device into the 3.0 port: Oct 21 01:09:54 gandalf root: Unknown USB device: vendor 0x090c product 0x1000 bus uhub4 Oct 21 01:09:54 gandalf kernel: ugen4.2:USB at usbus4 Oct 21 01:09:54 gandalf kernel: umass1:USB Flash Disk, class 0/0, rev 2.00/11.00, addr 1 on usbus4 Oct 21 01:09:54 gandalf kernel: umass1: SCSI over Bulk-Only; quirks = 0x Oct 21 01:09:55 gandalf kernel: umass1:10:1:-1: Attached to scbus10 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On 10/23/2010 23:12, Julian Elischer wrote: On 10/23/10 7:33 AM, Michael Martin wrote: On 10/23/2010 00:23, Hans Petter Selasky wrote: On Saturday 23 October 2010 02:07:59 Michael Martin wrote: On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4:My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001Western Digital iProduct = 0x0002My Book 3.0 iSerialNumber = 0x0003XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2:Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2:Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Output when plugging in the WD 3.0 into the 2.0 port: Oct 21 01:15:20 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub3 Oct 21 01:15:20 gandalf kernel: ugen3.4:Western Digital at usbus3 Oct 21 01:15:20 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 2.10/10.10, addr 4 on usbus3 Oct 21 01:15:20 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:15:21 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:15:28 gandalf kernel: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0 Oct 21 01:15:28 gandalf kernel: da0:WD My Book 3.0 1123 1010 Fixed Direct Access SCSI-4 device Oct 21 01:15:28 gandalf kernel: da0: 40.000MB/s transfers Oct 21 01:15:28 gandalf kernel: da0: 953867MB (1953519616 512 byte sectors: 255H 63S/T 121600C) Output when plugging in 2.0 device into the 3.0 port: Oct 21 01:09:54 gandalf root: Unknown USB device: vendor 0x090c product 0x1000 bus uhub4 Oct 21 01:09:54 gandalf kernel: ugen4.2:USB at usbus4 Oct 21 01:09:54 gandalf kernel: umass1:USB Flash Disk, class 0/0, rev 2.00/11.00, addr 1 on usbus4 Oct 21 01:09:54 gandalf kernel: umass1: SCSI over Bulk-Only; quirks = 0x Oct 21 01:09:55 gandalf kernel: umass1:10:1:-1: Attached to scbus10 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed) Oct 21 01:09:56 gandalf kernel: da1 at umass-sim1 bus 1 scbus10 target 0 lun 0 Oct 21 01:09:56 gandalf kernel: da1:USB Flash Disk 1100 Fixed Direct Access
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On Saturday 23 October 2010 02:07:59 Michael Martin wrote: On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4: My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001 Western Digital iProduct = 0x0002 My Book 3.0 iSerialNumber = 0x0003 XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2: Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0: Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2: Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Output when plugging in the WD 3.0 into the 2.0 port: Oct 21 01:15:20 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub3 Oct 21 01:15:20 gandalf kernel: ugen3.4: Western Digital at usbus3 Oct 21 01:15:20 gandalf kernel: umass0: Western Digital My Book 3.0, class 0/0, rev 2.10/10.10, addr 4 on usbus3 Oct 21 01:15:20 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:15:21 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:15:28 gandalf kernel: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0 Oct 21 01:15:28 gandalf kernel: da0: WD My Book 3.0 1123 1010 Fixed Direct Access SCSI-4 device Oct 21 01:15:28 gandalf kernel: da0: 40.000MB/s transfers Oct 21 01:15:28 gandalf kernel: da0: 953867MB (1953519616 512 byte sectors: 255H 63S/T 121600C) Output when plugging in 2.0 device into the 3.0 port: Oct 21 01:09:54 gandalf root: Unknown USB device: vendor 0x090c product 0x1000 bus uhub4 Oct 21 01:09:54 gandalf kernel: ugen4.2: USB at usbus4 Oct 21 01:09:54 gandalf kernel: umass1: USB Flash Disk, class 0/0, rev 2.00/11.00, addr 1 on usbus4 Oct 21 01:09:54 gandalf kernel: umass1: SCSI over Bulk-Only; quirks = 0x Oct 21 01:09:55 gandalf kernel: umass1:10:1:-1: Attached to scbus10 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed) Oct 21 01:09:56 gandalf kernel: da1 at umass-sim1 bus 1 scbus10 target 0 lun 0 Oct 21 01:09:56 gandalf
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On 10/23/2010 00:23, Hans Petter Selasky wrote: On Saturday 23 October 2010 02:07:59 Michael Martin wrote: On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4:My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001Western Digital iProduct = 0x0002My Book 3.0 iSerialNumber = 0x0003XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2:Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2:Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Output when plugging in the WD 3.0 into the 2.0 port: Oct 21 01:15:20 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub3 Oct 21 01:15:20 gandalf kernel: ugen3.4:Western Digital at usbus3 Oct 21 01:15:20 gandalf kernel: umass0:Western Digital My Book 3.0, class 0/0, rev 2.10/10.10, addr 4 on usbus3 Oct 21 01:15:20 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:15:21 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:15:28 gandalf kernel: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0 Oct 21 01:15:28 gandalf kernel: da0:WD My Book 3.0 1123 1010 Fixed Direct Access SCSI-4 device Oct 21 01:15:28 gandalf kernel: da0: 40.000MB/s transfers Oct 21 01:15:28 gandalf kernel: da0: 953867MB (1953519616 512 byte sectors: 255H 63S/T 121600C) Output when plugging in 2.0 device into the 3.0 port: Oct 21 01:09:54 gandalf root: Unknown USB device: vendor 0x090c product 0x1000 bus uhub4 Oct 21 01:09:54 gandalf kernel: ugen4.2:USB at usbus4 Oct 21 01:09:54 gandalf kernel: umass1:USB Flash Disk, class 0/0, rev 2.00/11.00, addr 1 on usbus4 Oct 21 01:09:54 gandalf kernel: umass1: SCSI over Bulk-Only; quirks = 0x Oct 21 01:09:55 gandalf kernel: umass1:10:1:-1: Attached to scbus10 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed) Oct 21 01:09:56 gandalf kernel: da1 at umass-sim1 bus 1 scbus10 target 0 lun 0 Oct 21 01:09:56 gandalf kernel: da1:USB Flash Disk 1100 Fixed Direct Access SCSI-0 device Oct 21 01:09:56 gandalf kernel: da1: 40.000MB/s transfers Oct 21 01:09:56 gandalf kernel: da1: 956MB
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On Saturday 23 October 2010 15:37:55 Michael Martin wrote: On 10/23/2010 00:23, Hans Petter Selasky wrote: On Saturday 23 October 2010 02:07:59 Michael Martin wrote: On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: Hi, From the logs you sent me I see that the super-speed inactive state is reached. There is currently no recovery from this state. I will send you a patch which you can try. --HPS ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On 10/21/2010 01:29, Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4: My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001 Western Digital iProduct = 0x0002 My Book 3.0 iSerialNumber = 0x0003 XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2: Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0: Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2: Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Output when plugging in the WD 3.0 into the 2.0 port: Oct 21 01:15:20 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub3 Oct 21 01:15:20 gandalf kernel: ugen3.4: Western Digital at usbus3 Oct 21 01:15:20 gandalf kernel: umass0: Western Digital My Book 3.0, class 0/0, rev 2.10/10.10, addr 4 on usbus3 Oct 21 01:15:20 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:15:21 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:15:28 gandalf kernel: da0 at umass-sim0 bus 0 scbus9 target 0 lun 0 Oct 21 01:15:28 gandalf kernel: da0: WD My Book 3.0 1123 1010 Fixed Direct Access SCSI-4 device Oct 21 01:15:28 gandalf kernel: da0: 40.000MB/s transfers Oct 21 01:15:28 gandalf kernel: da0: 953867MB (1953519616 512 byte sectors: 255H 63S/T 121600C) Output when plugging in 2.0 device into the 3.0 port: Oct 21 01:09:54 gandalf root: Unknown USB device: vendor 0x090c product 0x1000 bus uhub4 Oct 21 01:09:54 gandalf kernel: ugen4.2: USB at usbus4 Oct 21 01:09:54 gandalf kernel: umass1: USB Flash Disk, class 0/0, rev 2.00/11.00, addr 1 on usbus4 Oct 21 01:09:54 gandalf kernel: umass1: SCSI over Bulk-Only; quirks = 0x Oct 21 01:09:55 gandalf kernel: umass1:10:1:-1: Attached to scbus10 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): CAM status: SCSI Status Error Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI status: Check Condition Oct 21 01:09:56 gandalf kernel: (probe0:umass-sim1:1:0:0): SCSI sense: UNIT ATTENTION asc:28,0 (Not ready to ready change, medium may have changed) Oct 21 01:09:56 gandalf kernel: da1 at umass-sim1 bus 1 scbus10 target 0 lun 0 Oct 21 01:09:56 gandalf kernel: da1: USB Flash Disk 1100 Fixed Direct Access SCSI-0 device Oct 21 01:09:56 gandalf kernel: da1: 40.000MB/s transfers Oct 21 01:09:56 gandalf kernel: da1: 956MB (1957888 512 byte sectors: 64H 32S/T 956C) --Michael ( I never got the last list
Re: USB 3.0 Fails To Attach Western Digital My Book 3.0
On Thursday 21 October 2010 09:29:57 Michael Martin wrote: Thanks for the new USB 3.0 effort! I'm testing it out on 9.0-CURRENT amd64. The controller seems to find a 2.0 usb stick fine. However, when I plug in a Western Digital 3.0 drive, the device fails to attach. The WD drive attaches fine when plugging into a 2.0 port on the motherboard. Controller info: xh...@pci0:5:0:0: class=0x0c0330 card=0x chip=0x01941033 rev=0x03 hdr=0x00 vendor = 'NEC Electronics Hong Kong' class = serial bus subclass = USB bar [10] = type Memory, range 64, base 0xfbbfe000, size 8192, enabled cap 01[50] = powerspec 3 supports D0 D3 current D0 cap 05[70] = MSI supports 8 messages, 64 bit cap 11[90] = MSI-X supports 8 messages in map 0x10 cap 10[a0] = PCI-Express 2 endpoint max data 128(128) link x1(x1) ecap 0001[100] = AER 1 0 fatal 0 non-fatal 0 corrected ecap 0003[140] = Serial 1 ecap 0018[150] = unknown 1 WD 3.0 Drive Info ( while plugged into the 2.0 port ): ugen3.4: My Book 3.0 Western Digital at usbus3, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0210 bDeviceClass = 0x bDeviceSubClass = 0x bDeviceProtocol = 0x bMaxPacketSize0 = 0x0040 idVendor = 0x1058 idProduct = 0x1123 bcdDevice = 0x1010 iManufacturer = 0x0001 Western Digital iProduct = 0x0002 My Book 3.0 iSerialNumber = 0x0003 XXXRemovedXXX bNumConfigurations = 0x0001 Output when plugging in the Western Digital 3.0 into the 3.0 port: Oct 21 01:03:54 gandalf root: Unknown USB device: vendor 0x1058 product 0x1123 bus uhub4 Oct 21 01:03:54 gandalf kernel: ugen4.2: Western Digital at usbus4 Oct 21 01:03:54 gandalf kernel: umass0: Western Digital My Book 3.0, class 0/0, rev 3.00/10.10, addr 1 on usbus4 Oct 21 01:03:54 gandalf kernel: umass0: SCSI over Bulk-Only; quirks = 0x Oct 21 01:03:55 gandalf kernel: umass0:9:0:-1: Attached to scbus9 Oct 21 01:03:57 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:03:57 gandalf last message repeated 2 times Oct 21 01:03:57 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Oct 21 01:04:03 gandalf kernel: ugen4.2: Western Digital at usbus4 (disconnected) Oct 21 01:04:03 gandalf kernel: umass0: at uhub4, port 2, addr 1 (disconnected) Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): lost device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): got CAM status 0xa Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0:0:0): fatal error, failed to attach to device Oct 21 01:04:03 gandalf kernel: (da0:umass-sim0:0: Oct 21 01:04:03 gandalf kernel: 0:0): removing device entry Oct 21 01:04:14 gandalf root: ZFS: zpool I/O failure, zpool=wd3.1 error=28 Oct 21 01:04:14 gandalf last message repeated 2 times Oct 21 01:04:14 gandalf root: ZFS: vdev I/O failure, zpool=wd3.1 path= offset= size= error= Hi, 1) Try to enable UMASS debugging (you maybe need to rebuild kernel with options USB_DEBUG): sysctl hw.usb.umass.debug=-1 2) Also try to boot without umass in the kernel. What is the output from usbconfig, like descriptors, etc ... in USB 3.0 mode. --HPS ___ freebsd-usb@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to freebsd-usb-unsubscr...@freebsd.org