I dare any of the other "major competitors" to match Elecraft's response
time
73
Jay
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick
Sent: Tuesday, May 18, 2010 4:09 PM
To: elecraft...@yahoogroups.com
Cc: Elec
Perhaps I stated the question incorrectly.
Is there a list of the factory default parameters
in the configuration, so that one can compare the default
to the present setting.
Jay
__
Elecraft mailing list
Home: http://mailman.qth.net/mai
Thought there would be one of those in with the radio I got back yesterday
Wayne..:(
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Wayne Burdick
Sent: Tuesday, September 29, 2009 8:34 PM
To: Larry - K2GN
Cc: Elecraft - K3
S
Anyone have any luck running N1MM directly on a laptop with
no serial connector and a USB to serial convertor?
Primarily for cw?
Thanks
Jay
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: ht
I am able to access the bank 1 memories through N1MM and
figured how to access the Bank 2 memories also with N1MM.
however when I access the Bank 2 memories (N1MM F5-F8)
the F1 key then uses the Bank 2 K3 memories. That might not be clear
but what I want to end up with is N1MM F keys 1-8 acces
Thanks for all the answer
I have tried the level at about 10
seems to do the trick.
73
jay
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecr
I have a problem with noise in the shack.
On transmit it is picked up by the mic. Other than lowering the RF gain I
understand that
there is a setting which could reduce or eliminate this
some where in the config. Any tgoughts would be appreciated.
Thanks
Jay
Jay Rodaman
Programming N1MM to use the K3 memories 1-4 is a great aid, but is there a
way to address memories in the 2nd bank M5-M8 in the same fashion?
Thanks
Jay
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Iain MacDonnell -
N6ML
I guess to many times hitting the "delete" key...should have been "delight"
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jay Rodaman
Sent: Saturday, April 04, 2009 2:46 PM
To: elecraft@mailman
I have also had a similar need for external speakers.
The recommendation from an "unnamed source (heh heh) " on the left coast
was the following
http://www.bestbuy.com/site/olspage.jsp?skuId=7314523&type=product&id=111884
3685964
they are not very expensive , to the delete of most of us
and see
Thanks that did the trick..
Allu gots to du is aks ..lol
Jay
-Original Message-
From: Guy Olinger, K2AV [mailto:olin...@bellsouth.net]
Sent: Saturday, February 28, 2009 9:13 PM
To: Jay Rodaman; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 and N1MM (sub-rx)
This is an MM logger
I have turned on the sub-rx for diversity mode during the 160 test and find
the following.
1. The diversity works fine
2. When I click on the Q's and mults window the "sub" disengages
How can I keep the diversity mode engaged when clicking on spots?
Thanks
Jay
__
I had the same problem, but during construction, probably over tightened the
little set screw, Should remember
It is a radio not a truck
Jay
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ron Hinton
Sent: Tuesday, February 03, 2009 7:45 PM
To:
I second that!!
Jay(K2TTT)
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of DOUGLAS ZWIEBEL
Sent: Tuesday, January 27, 2009 7:38 AM
To: Elecraft Reflector
Subject: [Elecraft] why Elecraft is simply the BEST there is
RE: sto
It would be great if all you had to do was route a bnc jumper from RX ant
OUT to the AUX ant on the sub-
Receiver and in that way when the sub was active it would use the receive
antenna for diversity
And when inactive it would be the main receiver REC antenna.
-Original Message-
From: el
Just finished my K3 works great
Interfaced with the microkeyer
which reads the frequency and keys cw fine.
Now I need to configure N1MM to put it all together.
Created ports as follows in Router
2=Radio
3=Ptt
6=foot switch
8=winkey.
Can someone help me get N1MM configurer to
put all this together,
Just setting up my new K3 with sub receiver.
I have the Original Microkeyer and got the matching cable set for the K3
Question is:
There are two connectors that I do not know where to connect
1.RCA female marked "INHIBIT"
2. Female mini-plug marked "SUB RX"
Where do these go?
Thanks for any help
Ja
Just getting my K3 up and running. I have a K9AY loop and would like to
Have that as the receive antenna each time I change band to 160/80
Is there a way for the radio to remember this activity? Or do
I have to press the rcv antenna switch each time?
Comments appreciated.
BTW a million t
18 matches
Mail list logo