Re: still problems with manual tape changer using tapespan
On 02/20/2013 07:07 AM, Jean-Louis Martineau wrote: On 02/20/2013 06:59 AM, Karsten Fuhrmann wrote: Hello Jean-Louis, should i apply the path on trunk or release 3.3.3? The patch apply to trunk and the 3-3 branch, I haven't tested if apply cleanly on the release 3.3.3 but I think it should. Karsten, Let me know if the patch works for you. Jean-Louis
Re: still problems with manual tape changer using tapespan
On 02/20/2013 06:59 AM, Karsten Fuhrmann wrote: Hello Jean-Louis, should i apply the path on trunk or release 3.3.3? The patch apply to trunk and the 3-3 branch, I haven't tested if apply cleanly on the release 3.3.3 but I think it should. Jean-Louis
Re: still problems with manual tape changer using tapespan
Hello Jean-Louis,
should i apply the path on trunk or release 3.3.3?
On 19.02.2013, at 20:58, Jean-Louis Martineau wrote:
> Hello Karsten,
>
> Can you try the attached patch?
>
>
> Jean-Louis
>
>
> On 02/18/2013 06:57 AM, Karsten Fuhrmann wrote:
>> I still can't get tapespan to work, with my single tape drive setup.
>> I added interactivity and tapescan to amanda.conf. And updated amanda to
>> version 3.3.3
>>
>> Now even when i load the right tape into the tapedrive, when i run amcheck,
>> i got the following message by email:
>>
>>
>> No acceptable volumes found
>>
>> Insert volume labeled 'cf-daily-lto8' in chg-single:tape:/dev/nsa0
>> or write the name of a new changer in '/tmp/email_input'
>> or write 'abort' in the file to abort the scan.
>>
>> if i write 'abort' into /tmp/email_input it aborts. but if i just touch
>> /tmp/email_input to tell amanda that the proper tape is inserted, i get the
>> above email again. What is going on here?
>> My shell session looks like this:
>>
>> % sudo -u amanda amcheck cf-daily-lto
>> Amanda Tape Server Host Check
>> -
>> WARNING: holding disk /mnt/amanda-holding: only 4 GB free, using nothing
>> WARNING: Not enough free space specified in amanda.conf
>> slot 0: volume 'cf-daily-lto8'
>> slot 0: volume 'cf-daily-lto8'
>>
>> The second 'slot 0: volume 'cf-daily-lto8' comes after i touched the
>> /tmp/email_input file.
>>
>> Here are the relevant parts of my amanda.conf:
>>
>> define taperscan le_scan {
>>comment "bla"
>>plugin "lexical"
>> }
>>
>> define interactivity email {
>> comment "interactivity email"
>> plugin "email"
>> property "mailto" "administrat...@cartoon-film.de"
>> property "resend_delay" "0"
>> property "check-file" "/tmp/email_input"
>> property "check-file-delay" "10"
>> }
>> interactivity "email"
>> taperscan "le_scan"
>>
>> tpchanger "chg-single:tape:/dev/nsa0"
>>
>>
>> Please help me, this thing is killing me.
>>
>>
>> On 14.02.2013, at 18:13, Karsten Fuhrmann wrote:
>>
>>> Hi, now i added this:
>>>
>>> define taperscan oldest {
>>> comment "bla"
>>> plugin "oldest"
>>> }
>>> taperscan "oldest"
>>>
>>> into my amanda.conf. Now i got an email to change the tape. But then i am
>>> stuck, amanda does not notice the newly inserted tape, and also does not
>>> react on the file /tmp/email_input i created with touch.
>>> It just waits forever. What am i missing?
>>>
>>>
>>> On 14.02.2013, at 16:53, Jean-Louis Martineau wrote:
>>>
On 02/14/2013 10:00 AM, Karsten Fuhrmann wrote:
> Hello,
> i tried that but does not work. I dont get an email to change the tape,
> instead amanda quits with:
>
> FAILURE DUMP SUMMARY:
> datastore /tank/koh/user/./k-o lev 0 partial taper: No acceptable
> volumes found
>
> i added the following in my amanda.conf:
>
> define interactivity email {
> comment "interactivity email"
> plugin "email"
> property "mailto" "administrat...@cartoon-film.de"
> property "resend_delay" "0"
> property "check-file" "/tmp/email_input"
> property "check-file-delay" "10"
> }
> interactivity "email"
>
>
The default taperscan do not use the interactivity module, you must use
the 'oldest' or 'lexical' taperscan.
see: man amanda-taperscan
Jean-Louis
>>> Greetings,
>>> Karsten Fuhrmann
>>> System Administrator
>>> Rothkirch Cartoon-Film GmbH
>>> Hasenheide. 54
>>> D-10967 Berlin
>>> phone +49 30 698084-109
>>> fax +49 30 698084-29
>>> mobile +49 176 49118462
>>> skype: parceval3000
>>> AIM: in...@mac.com
>>> Jabber: parce...@jabber.org
>>>
>>>
>> Greetings,
>> Karsten Fuhrmann
>>
>
>
Greetings,
Karsten Fuhrmann
System Administrator
Rothkirch Cartoon-Film GmbH
Hasenheide. 54
D-10967 Berlin
phone +49 30 698084-109
fax +49 30 698084-29
mobile +49 176 49118462
skype: parceval3000
AIM: in...@mac.com
Jabber: parce...@jabber.org
Re: still problems with manual tape changer using tapespan
Hello Karsten,
Can you try the attached patch?
Jean-Louis
On 02/18/2013 06:57 AM, Karsten Fuhrmann wrote:
I still can't get tapespan to work, with my single tape drive setup.
I added interactivity and tapescan to amanda.conf. And updated amanda to
version 3.3.3
Now even when i load the right tape into the tapedrive, when i run amcheck, i
got the following message by email:
No acceptable volumes found
Insert volume labeled 'cf-daily-lto8' in chg-single:tape:/dev/nsa0
or write the name of a new changer in '/tmp/email_input'
or write 'abort' in the file to abort the scan.
if i write 'abort' into /tmp/email_input it aborts. but if i just touch
/tmp/email_input to tell amanda that the proper tape is inserted, i get the
above email again. What is going on here?
My shell session looks like this:
% sudo -u amanda amcheck cf-daily-lto
Amanda Tape Server Host Check
-
WARNING: holding disk /mnt/amanda-holding: only 4 GB free, using nothing
WARNING: Not enough free space specified in amanda.conf
slot 0: volume 'cf-daily-lto8'
slot 0: volume 'cf-daily-lto8'
The second 'slot 0: volume 'cf-daily-lto8' comes after i touched the
/tmp/email_input file.
Here are the relevant parts of my amanda.conf:
define taperscan le_scan {
comment "bla"
plugin "lexical"
}
define interactivity email {
comment "interactivity email"
plugin "email"
property "mailto" "administrat...@cartoon-film.de"
property "resend_delay" "0"
property "check-file" "/tmp/email_input"
property "check-file-delay" "10"
}
interactivity "email"
taperscan "le_scan"
tpchanger "chg-single:tape:/dev/nsa0"
Please help me, this thing is killing me.
On 14.02.2013, at 18:13, Karsten Fuhrmann wrote:
Hi, now i added this:
define taperscan oldest {
comment "bla"
plugin "oldest"
}
taperscan "oldest"
into my amanda.conf. Now i got an email to change the tape. But then i am
stuck, amanda does not notice the newly inserted tape, and also does not react
on the file /tmp/email_input i created with touch.
It just waits forever. What am i missing?
On 14.02.2013, at 16:53, Jean-Louis Martineau wrote:
On 02/14/2013 10:00 AM, Karsten Fuhrmann wrote:
Hello,
i tried that but does not work. I dont get an email to change the tape, instead
amanda quits with:
FAILURE DUMP SUMMARY:
datastore /tank/koh/user/./k-o lev 0 partial taper: No acceptable volumes found
i added the following in my amanda.conf:
define interactivity email {
comment "interactivity email"
plugin "email"
property "mailto" "administrat...@cartoon-film.de"
property "resend_delay" "0"
property "check-file" "/tmp/email_input"
property "check-file-delay" "10"
}
interactivity "email"
The default taperscan do not use the interactivity module, you must use the
'oldest' or 'lexical' taperscan.
see: man amanda-taperscan
Jean-Louis
Greetings,
Karsten Fuhrmann
System Administrator
Rothkirch Cartoon-Film GmbH
Hasenheide. 54
D-10967 Berlin
phone +49 30 698084-109
fax +49 30 698084-29
mobile +49 176 49118462
skype: parceval3000
AIM: in...@mac.com
Jabber: parce...@jabber.org
Greetings,
Karsten Fuhrmann
diff --git a/perl/Amanda/Changer/single.pm b/perl/Amanda/Changer/single.pm
index 8417d02..2e51062 100644
--- a/perl/Amanda/Changer/single.pm
+++ b/perl/Amanda/Changer/single.pm
@@ -66,6 +66,11 @@ sub new {
config => $config,
device_name => $device_name,
reserved => 0,
+ state => undef,
+ device_status => undef,
+ f_type => undef,
+ label => undef,
+ 'scan-require-update' => 1,
};
bless ($self, $class);
@@ -82,9 +87,18 @@ sub load {
confess "no res_cb supplied" unless (exists $params{'res_cb'});
if ($self->{'reserved'}) {
- return $self->make_error("failed", $params{'res_cb'},
- reason => "volinuse",
- message => "'$self->{device_name}' is already reserved");
+ if (($self->{'label'} and $params{'label'} and
+ $self->{'label'} eq $params{'label'}) or
+ ($self->{'slot'} and $params{'slot'} and
+ $self->{'slot'} eq $params{'slot'})) {
+ return $self->make_error("failed", $params{'res_cb'},
+ reason => "volinuse",
+ message => "'$self->{device_name}' is already reserved");
+ } else {
+ return $self->make_error("failed", $params{'res_cb'},
+ reason => "driveinuse",
+ message => "'$self->{device_name}' is already reserved");
+ }
}
if (keys %{$params{'except_slots'}} > 0) {
@@ -94,6 +108,10 @@ sub load {
}
my $device = Amanda::Device->new($self->{'device_name'});
+$self->{'state'} = Amanda::Changer::SLOT_FULL;
+$self->{'device_status'} = $device->status();
+$self->{'f_type'} = undef;
+$self->{'label'} = undef;
if ($device->status() != $DEVICE_STATUS_SUCCESS) {
return $self->make_error("fatal", $params{'res_cb'},
message => "error opening device '$self->{device_name}': " . $device->error_or_status());
@@ -109,6 +127,14 @@ sub load {
my $res = Amanda::Changer::single::Reservation->new($self, $device);
$device->read_
Re: still problems with manual tape changer using tapespan
Karsten,
Sorry to not replying sooner.
I found a bug and i'm working on a fix, it should be ready this week.
Jean-Louis
On 02/18/2013 06:57 AM, Karsten Fuhrmann wrote:
I still can't get tapespan to work, with my single tape drive setup.
I added interactivity and tapescan to amanda.conf. And updated amanda to
version 3.3.3
Now even when i load the right tape into the tapedrive, when i run amcheck, i
got the following message by email:
No acceptable volumes found
Insert volume labeled 'cf-daily-lto8' in chg-single:tape:/dev/nsa0
or write the name of a new changer in '/tmp/email_input'
or write 'abort' in the file to abort the scan.
if i write 'abort' into /tmp/email_input it aborts. but if i just touch
/tmp/email_input to tell amanda that the proper tape is inserted, i get the
above email again. What is going on here?
My shell session looks like this:
% sudo -u amanda amcheck cf-daily-lto
Amanda Tape Server Host Check
-
WARNING: holding disk /mnt/amanda-holding: only 4 GB free, using nothing
WARNING: Not enough free space specified in amanda.conf
slot 0: volume 'cf-daily-lto8'
slot 0: volume 'cf-daily-lto8'
The second 'slot 0: volume 'cf-daily-lto8' comes after i touched the
/tmp/email_input file.
Here are the relevant parts of my amanda.conf:
define taperscan le_scan {
comment "bla"
plugin "lexical"
}
define interactivity email {
comment "interactivity email"
plugin "email"
property "mailto" "administrat...@cartoon-film.de"
property "resend_delay" "0"
property "check-file" "/tmp/email_input"
property "check-file-delay" "10"
}
interactivity "email"
taperscan "le_scan"
tpchanger "chg-single:tape:/dev/nsa0"
Please help me, this thing is killing me.
On 14.02.2013, at 18:13, Karsten Fuhrmann wrote:
Hi, now i added this:
define taperscan oldest {
comment "bla"
plugin "oldest"
}
taperscan "oldest"
into my amanda.conf. Now i got an email to change the tape. But then i am
stuck, amanda does not notice the newly inserted tape, and also does not react
on the file /tmp/email_input i created with touch.
It just waits forever. What am i missing?
On 14.02.2013, at 16:53, Jean-Louis Martineau wrote:
On 02/14/2013 10:00 AM, Karsten Fuhrmann wrote:
Hello,
i tried that but does not work. I dont get an email to change the tape, instead
amanda quits with:
FAILURE DUMP SUMMARY:
datastore /tank/koh/user/./k-o lev 0 partial taper: No acceptable volumes found
i added the following in my amanda.conf:
define interactivity email {
comment "interactivity email"
plugin "email"
property "mailto" "administrat...@cartoon-film.de"
property "resend_delay" "0"
property "check-file" "/tmp/email_input"
property "check-file-delay" "10"
}
interactivity "email"
The default taperscan do not use the interactivity module, you must use the
'oldest' or 'lexical' taperscan.
see: man amanda-taperscan
Jean-Louis
Greetings,
Karsten Fuhrmann
System Administrator
Rothkirch Cartoon-Film GmbH
Hasenheide. 54
D-10967 Berlin
phone +49 30 698084-109
fax +49 30 698084-29
mobile +49 176 49118462
skype: parceval3000
AIM: in...@mac.com
Jabber: parce...@jabber.org
Greetings,
Karsten Fuhrmann
still problems with manual tape changer using tapespan
I still can't get tapespan to work, with my single tape drive setup.
I added interactivity and tapescan to amanda.conf. And updated amanda to
version 3.3.3
Now even when i load the right tape into the tapedrive, when i run amcheck, i
got the following message by email:
No acceptable volumes found
Insert volume labeled 'cf-daily-lto8' in chg-single:tape:/dev/nsa0
or write the name of a new changer in '/tmp/email_input'
or write 'abort' in the file to abort the scan.
if i write 'abort' into /tmp/email_input it aborts. but if i just touch
/tmp/email_input to tell amanda that the proper tape is inserted, i get the
above email again. What is going on here?
My shell session looks like this:
% sudo -u amanda amcheck cf-daily-lto
Amanda Tape Server Host Check
-
WARNING: holding disk /mnt/amanda-holding: only 4 GB free, using nothing
WARNING: Not enough free space specified in amanda.conf
slot 0: volume 'cf-daily-lto8'
slot 0: volume 'cf-daily-lto8'
The second 'slot 0: volume 'cf-daily-lto8' comes after i touched the
/tmp/email_input file.
Here are the relevant parts of my amanda.conf:
define taperscan le_scan {
comment "bla"
plugin "lexical"
}
define interactivity email {
comment "interactivity email"
plugin "email"
property "mailto" "administrat...@cartoon-film.de"
property "resend_delay" "0"
property "check-file" "/tmp/email_input"
property "check-file-delay" "10"
}
interactivity "email"
taperscan "le_scan"
tpchanger "chg-single:tape:/dev/nsa0"
Please help me, this thing is killing me.
On 14.02.2013, at 18:13, Karsten Fuhrmann wrote:
> Hi, now i added this:
>
> define taperscan oldest {
> comment "bla"
> plugin "oldest"
> }
> taperscan "oldest"
>
> into my amanda.conf. Now i got an email to change the tape. But then i am
> stuck, amanda does not notice the newly inserted tape, and also does not
> react on the file /tmp/email_input i created with touch.
> It just waits forever. What am i missing?
>
>
> On 14.02.2013, at 16:53, Jean-Louis Martineau wrote:
>
>> On 02/14/2013 10:00 AM, Karsten Fuhrmann wrote:
>>> Hello,
>>> i tried that but does not work. I dont get an email to change the tape,
>>> instead amanda quits with:
>>>
>>> FAILURE DUMP SUMMARY:
>>> datastore /tank/koh/user/./k-o lev 0 partial taper: No acceptable volumes
>>> found
>>>
>>> i added the following in my amanda.conf:
>>>
>>> define interactivity email {
>>> comment "interactivity email"
>>> plugin "email"
>>> property "mailto" "administrat...@cartoon-film.de"
>>> property "resend_delay" "0"
>>> property "check-file" "/tmp/email_input"
>>> property "check-file-delay" "10"
>>> }
>>> interactivity "email"
>>>
>>>
>> The default taperscan do not use the interactivity module, you must use the
>> 'oldest' or 'lexical' taperscan.
>> see: man amanda-taperscan
>>
>> Jean-Louis
>>
>
> Greetings,
> Karsten Fuhrmann
> System Administrator
> Rothkirch Cartoon-Film GmbH
> Hasenheide. 54
> D-10967 Berlin
> phone +49 30 698084-109
> fax +49 30 698084-29
> mobile +49 176 49118462
> skype: parceval3000
> AIM: in...@mac.com
> Jabber: parce...@jabber.org
>
>
Greetings,
Karsten Fuhrmann
