If you just get a few error 500's at startup - these can be ignored. I
get these all the time, and the few a the beginning do not seem to cause a
problem.
However, if you get lots of them when you are receiving traffic (incoming
calls), I think it has something to do with the PRI frame buffer overflow
problem that Digium is aware of. I get dozens of these along with hundreds
of frame retries when I have lots of traffic.
If the latter, please email [EMAIL PROTECTED] as well, to make sure they
have it on their list.
Regards
Scott
Scott M. Stingel
Emerging Voice Technology Inc.
Email: [EMAIL PROTECTED] mailto:[EMAIL PROTECTED]
URL:www.evtmedia.com http://www.evtmedia.com
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of bam
Sent: Monday, December 29, 2003 4:01 PM
To: [EMAIL PROTECTED]
Subject: RE: [Asterisk-Users] E100P pinouts anyone?
Thanks for that, I had used 12 and 56. Doh!
The datalink now comes up, but I get repeated messages about an unknown
error. There is only one reference in the archives and it was never
answered, so I'm stuck again.
WARNING[180236]: File chan_zap.c. Line 5733 (zt_pri_error): PRI read on 48
failed: Unknown error 500 PRI got event: 8
At 15:25 29/12/03, you wrote:
Just cross pairs 1-2 and 4-5
1 -- 4
2 -- 5
Never done an E1, but I think it's the same for a T1 4 wire cable.
Tim Thompson
Commercial Sales Engineer
http://www.amatechtel.com
(806) 722-2227
-Original Message-
From: bam [mailto:[EMAIL PROTECTED]
Sent: Monday, December 29, 2003 9:12 AM
To: [EMAIL PROTECTED]
Subject: [Asterisk-Users] E100P pinouts anyone?
I'm trying to hookup an E100P to an E1 PRI that I know is working, it
drives an Ascend Max happily. The E100P has a red LED flashing away
slowly
and the telco switch reports that there is no level one signalling link.
So that I can rule out the obvious things does anyone have the pinouts
for
the RJ45 on the E100P? I've tried straight through and crossover to no
avail.
I get a couple of errors on modprobing the driver, but if I reverse the
order it seems to load OK. ztcfg is happy and zttool seems to see the
card
so I'm pretty certain it is something silly.
any help gratefully received.
Brian
[EMAIL PROTECTED] root]# modprobe zaptel
[EMAIL PROTECTED] root]# modprobe wct1xxp
ZT_CHANCONFIG failed on channel 32: No such device or address (6)
/lib/modules/2.4.20-24.9/misc/wct1xxp.o: post-install wct1xxp failed
/lib/modules/2.4.20-24.9/misc/wct1xxp.o: insmod wct1xxp failed
[EMAIL PROTECTED] root]# modprobe wcfxs
[EMAIL PROTECTED] root]# modprobe wct1xxp
[EMAIL PROTECTED] root]#
___
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
___
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
___
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
___
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
