Re: [asterisk-users] TDM400P Problem or Not?
With a TDM 400 card in the system, WHY do you even need ztdummy?? I thought that was a substitute when there was no other timing source The only time I have had to compile ztdummy is when there was NO card present. Of course, I could be wrong. Please enlighten John Novack Eddie Johnson Jr wrote: Hello, I am having a problem. I have aterisk1.2.11 installed on ubuntu server 6.06 dapper and I have the ztdummy module listed in /etc/modules directory however upon startup it will not load. I type lsmod | grep ztdummy and there is no output. I then ran a config file for asterisk to create startup config files and it installs. I restarted the server with the newly installed files, and I type asterisk and asterisk starts. I do this issue a command to connect remotely and receive the connection and I type zap show status and I have the following: Alarms IRQ bpviol CRC4 Wildcard TDM400P REV I Board1 OK 0 0 ZTDUMMY/1 1 UNCONFUR 0 0 0 I type stop now, go back to the prompt type mdprobe ztdummy and it loads. I repeat the above procedures above and I get the same message. Any suggestsions? Ed ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] TDM400P Problem
Hi, Just received the TDM400P and X100P. PC can detect the X100P, but not the TDM400P. Tried to load the wcfxs module, reported: modprobe wcfxs /lib/modules/2.4.20-20.9/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters,including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20-20.9/misc/wcfxs.o: insmod /lib/modules/2.4.20-20.9/misc/wcfxs.o failed /lib/modules/2.4.20-20.9/misc/wcfxs.o: insmod wcfxs failedAny advise. Thanks.
Re: [Asterisk-Users] TDM400P Problem
I had the same thing and just figured it out yesterday! the problem is that the tdm400p is failing calibration. type "dmesg" and it will tell you. uncomment in zaptel/Makefile KFLAGS+=-DNO_CALIBRATION in the source code and "make clean install" It worked for me but I wonder if there is a bad batch of cards? I was in the "backordered till Sept 2nd batch" I am assuming its not good to fail calibration? Steve Totaro - Original Message - From: How Peng Kaiam To: [EMAIL PROTECTED] Sent: Thursday, September 11, 2003 9:52 AM Subject: [Asterisk-Users] TDM400P Problem Hi, Just received the TDM400P and X100P. PC can detect the X100P, but not the TDM400P. Tried to load the wcfxs module, reported: modprobe wcfxs /lib/modules/2.4.20-20.9/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters,including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20-20.9/misc/wcfxs.o: insmod /lib/modules/2.4.20-20.9/misc/wcfxs.o failed /lib/modules/2.4.20-20.9/misc/wcfxs.o: insmod wcfxs failedAny advise. Thanks.
Re: [Asterisk-Users] TDM400P Problem
I may have the same problem. When I try to load wcfxs driver, it fails after reading register 8 on the ProSLIC. See following log: kernel: ProSLIC on module 0, product 0, version 5 kernel: ProSLIC on module 0 insane (1) 0 should be 2 kernel: Module 0: Not installed Can anyone point me to a data sheet on this ProSLIC device. I would like to dump the regs and kick it around a little to see if it can do anything that makes sense. It is aways hard to tell when you are bit banging on a device. btw: digium support suggested taking the mounting bracket off. Did not work for me. Steve Totaro wrote: I had the same thing and just figured it out yesterday! the problem is that the tdm400p is failing calibration. type "dmesg" and it will tell you. uncomment in zaptel/Makefile KFLAGS+=-DNO_CALIBRATION in the source code and "make clean install" It worked for me but I wonder if there is a bad batch of cards? I was in the "backordered till Sept 2nd batch" I am assuming its not good to fail calibration? Steve Totaro - Original Message - From: How Peng Kaiam To: [EMAIL PROTECTED] Sent: Thursday, September 11, 2003 9:52 AM Subject: [Asterisk-Users] TDM400P Problem Hi, Just received the TDM400P and X100P. PC can detect the X100P, but not the TDM400P. Tried to load the wcfxs module, reported: modprobe wcfxs /lib/modules/2.4.20-20.9/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20-20.9/misc/wcfxs.o: insmod /lib/modules/2.4.20-20.9/misc/wcfxs.o failed /lib/modules/2.4.20-20.9/misc/wcfxs.o: insmod wcfxs failed Any advise. Thanks. -- Bob Knight [-w] the work option [EMAIL PROTECTED] 925-449-9163
