[OSL | CCIE_Voice] No audio on Calls from CUCM to CME SIP phone using CUBE
Hi All, I have the CUBE setup on the HQ GW CUCM to CUBE = SIP CUME to CME = h323 Codec is g729 across. Calls work fine to the CME sccp phone. However calls from CUCM to SIP CME phone has no audio. Below are my configs. HQ Config voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip h323 emptycapability h225 connect-passthru h245 passthru tcsnonstd-passthru sip bind control source-interface FastEthernet0/0 bind media source-interface FastEthernet0/0 ! ! dial-peer voice 4000 voip destination-pattern 4... session target ipv4:10.10.202.1 incoming called-number [23]... dtmf-relay h245-alphanumeric ! dial-peer voice 2300 voip destination-pattern [23]... session protocol sipv2 session target ipv4:10.137.151.26 incoming called-number 4... dtmf-relay rtp-nte ! *** CME Config *** voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip sip bind control source-interface GigabitEthernet0/0.400 bind media source-interface GigabitEthernet0/0.400 registrar server ! ! ! ! ! ! ! ! ! ! ! ! ! voice register global mode cme source-address 10.10.202.1 port 5060 max-dn 15 max-pool 5 load 7965 SIP45.8-4-4S timezone 21 create profile sync 0206597300406331 ntp-server 10.137.151.250 mode directedbroadcast ! voice register dn 1 number 4002 name Site C Phone 2 ! voice register pool 1 id mac 0024.C40B.13DC type 7965 number 1 dn 1 dtmf-relay rtp-nte ! I enable SIP EO with MTP and still the same result. Hope you guys can see something I am missing. Thanks, DA ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Lab 4A
Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] CCIE Voice Lab 4A
Hi I can dial 999 from my BR2 Router but from PSNT I can not call BR2 Phones. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
do you get dial tone ? make sure you create your incoming pots dial peer and DID enabled, also make sure you have a translation rule to strip 3214 or 343214 or +343214 dial-peer voice 1 pots incoming called-number . direct inward dial 2010/11/29 Rafay Aslam rafayc...@gmail.com Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
HI, If you can call OB you still need to make sure your config for IB is correct. You need an IB dial peer and a translation rule to strip down the called number to 3001 HTH Randall From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Rafay Aslam Sent: Monday, November 29, 2010 8:24 AM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Lab 4A Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards Legal Disclaimer: The information contained in this message may be privileged and confidential. It is intended to be read only by the individual or entity to whom it is addressed or by their designee. If the reader of this message is not the intended recipient, you are on notice that any distribution of this message, in any form, is strictly prohibited. If you have received this message in error, please immediately notify the sender and delete or destroy any copy of this message ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] SCCP- CUCM -GK-CME-SIP Phone call failing
Hi All , call flow SCCP- CUCM -GK-CME-SIP I enabled inbound faststart and call from SIP from CME to sccp phone of cucm is working fine. but when call is placed in opposite direction , after 1st ring , call is getting disconnected. I enabled outbound faststart with cucm MTP in MRGL but no luck . Any idea ? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
Hi Rafay, on Br2-RTR# debug isdn q931 to see whether the call is reaching gateway. On gateway Significant digits 4. It should work. Thanks Shrini On 11/29/2010 8:23 AM, Rafay Aslam wrote: Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] SCCP- CUCM -GK-CME-SIP Phone call failing
have you check the codec ? i think that from sccp -cucm is G.729 CME-SIP only supports G.711 if that's the case register a transcoder on the cme 2010/11/29 Mritunjay Kumar mjs...@gmail.com Hi All , call flow SCCP- CUCM -GK-CME-SIP I enabled inbound faststart and call from SIP from CME to sccp phone of cucm is working fine. but when call is placed in opposite direction , after 1st ring , call is getting disconnected. I enabled outbound faststart with cucm MTP in MRGL but no luck . Any idea ? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
Hi I have inital configuration loaded from PSTN router, here is debug from PSTN Router, I am calling from PSTN Phone to 3214-3005, so basically I want to see if my translation pattern works on BR2 Router whyic PSTN-WAN# Nov 29 20:07:25.135: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:28.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:30.063: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0080 callID = 0x8001 switch = primary-ni interface = Network Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0080 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '+3432143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.119: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8080 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.131: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8080 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.135: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0080 Nov 29 20:07:30.143: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8080 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0081 callID = 0x8002 switch = primary-ni interface = Network Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0081 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '32143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.183: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8081 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.191: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8081 * Cause i = 0x8081 - Unallocated/unassigned number *Nov 29 20:07:30.195: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0081 Nov 29 20:07:30.203: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8081 Nov 29 20:07:34.139: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:37.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 On Mon, Nov 29, 2010 at 12:04 PM, Randall Crumm randall.cr...@flextronics.com wrote: HI, If you can call OB you still need to make sure your config for IB is correct. You need an IB dial peer and a translation rule to strip down the called number to 3001 HTH Randall *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Rafay Aslam *Sent:* Monday, November 29, 2010 8:24 AM *To:* ccie_voice@onlinestudylist.com *Subject:* [OSL | CCIE_Voice] Lab 4A Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards Legal Disclaimer: The information contained in this message may be privileged and confidential. It is intended to be read only by the individual or entity to whom it is addressed or by their designee. If the reader of this message is not the intended recipient, you are on notice that any distribution of this message, in any form, is strictly prohibited. If you have received this message in error, please immediately notify the sender and delete or destroy any copy of this message ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
Can you send your voice translation rule/profile and how it is applied to the voice port? From: Rafay Aslam [mailto:rafayc...@gmail.com] Sent: Monday, November 29, 2010 12:11 PM To: Randall Crumm Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Lab 4A Hi I have inital configuration loaded from PSTN router, here is debug from PSTN Router, I am calling from PSTN Phone to 3214-3005, so basically I want to see if my translation pattern works on BR2 Router whyic PSTN-WAN# Nov 29 20:07:25.135: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:28.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:30.063: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0080 callID = 0x8001 switch = primary-ni interface = Network Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0080 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '+3432143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.119: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8080 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.131: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8080 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.135: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0080 Nov 29 20:07:30.143: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8080 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0081 callID = 0x8002 switch = primary-ni interface = Network Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0081 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '32143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.183: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8081 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.191: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8081 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.195: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0081 Nov 29 20:07:30.203: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8081 Nov 29 20:07:34.139: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:37.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 On Mon, Nov 29, 2010 at 12:04 PM, Randall Crumm randall.cr...@flextronics.com wrote: HI, If you can call OB you still need to make sure your config for IB is correct. You need an IB dial peer and a translation rule to strip down the called number to 3001 HTH Randall From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Rafay Aslam Sent: Monday, November 29, 2010 8:24 AM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Lab 4A Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards Legal Disclaimer: The information contained in this message may be privileged and confidential. It is intended to be read only by the individual or entity to whom it is addressed or by their designee. If the reader of this message is not the intended recipient, you are on notice that any distribution of this message, in any form, is strictly prohibited. If you have received this message in error, please immediately notify the sender and delete or destroy any copy of this message ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
Hi Attach is a complete PSNT Config. On Mon, Nov 29, 2010 at 3:12 PM, Randall Crumm randall.cr...@flextronics.com wrote: Can you send your voice translation rule/profile and how it is applied to the voice port? *From:* Rafay Aslam [mailto:rafayc...@gmail.com] *Sent:* Monday, November 29, 2010 12:11 PM *To:* Randall Crumm *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] Lab 4A Hi I have inital configuration loaded from PSTN router, here is debug from PSTN Router, I am calling from PSTN Phone to 3214-3005, so basically I want to see if my translation pattern works on BR2 Router whyic PSTN-WAN# Nov 29 20:07:25.135: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:28.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:30.063: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0080 callID = 0x8001 switch = primary-ni interface = Network Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0080 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '+3432143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.119: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8080 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.131: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8080 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.135: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0080 Nov 29 20:07:30.143: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8080 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0081 callID = 0x8002 switch = primary-ni interface = Network Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0081 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '32143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.183: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8081 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.191: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8081 * Cause i = 0x8081 - Unallocated/unassigned number** *Nov 29 20:07:30.195: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0081 Nov 29 20:07:30.203: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8081 Nov 29 20:07:34.139: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:37.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 On Mon, Nov 29, 2010 at 12:04 PM, Randall Crumm randall.cr...@flextronics.com wrote: HI, If you can call OB you still need to make sure your config for IB is correct. You need an IB dial peer and a translation rule to strip down the called number to 3001 HTH Randall *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Rafay Aslam *Sent:* Monday, November 29, 2010 8:24 AM *To:* ccie_voice@onlinestudylist.com *Subject:* [OSL | CCIE_Voice] Lab 4A Hi I am doing Lab 4A, I can call from my BR2 Router to 999 or 911 which is PSTN Phone but from PSTN Phone I am unable to call my BR2 Phones ie 3214-3001 Regards Legal Disclaimer: The information contained in this message may be privileged and confidential. It is intended to be read only by the individual or entity to whom it is addressed or by their designee. If the reader of this message is not the intended recipient, you are on notice that any distribution of this message, in any form, is strictly prohibited. If you have received this message in error, please immediately notify the sender and delete or destroy any copy of this message PSTN-WAN#sh run Building configuration... Current configuration :
Re: [OSL | CCIE_Voice] Lab 4A
Hi Rafay, Can you send the configuration from Site C? He was referring to the translation profile applied incoming on the voice-port on R3. It should look something like this: Voice-translation-rule 1 Rule 1 /^32143/ /3/ Or (I see two different called numbers below) Voice translation-rule 1 Rule 1 /^\+3432143/ /3/ Then create the profile and apply to voice-port Voice-translation-profile PSTN-IN Translate called 1 Voice-port 0/0/0:15 Translation-profile incoming PSTN-IN Jeff From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Rafay Aslam Sent: Monday, November 29, 2010 1:22 PM To: Randall Crumm Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Lab 4A Hi Attach is a complete PSNT Config. On Mon, Nov 29, 2010 at 3:12 PM, Randall Crumm randall.cr...@flextronics.com wrote: Can you send your voice translation rule/profile and how it is applied to the voice port? From: Rafay Aslam [mailto:rafayc...@gmail.com] Sent: Monday, November 29, 2010 12:11 PM To: Randall Crumm Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Lab 4A Hi I have inital configuration loaded from PSTN router, here is debug from PSTN Router, I am calling from PSTN Phone to 3214-3005, so basically I want to see if my translation pattern works on BR2 Router whyic PSTN-WAN# Nov 29 20:07:25.135: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:28.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:30.063: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0080 callID = 0x8001 switch = primary-ni interface = Network Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0080 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '+3432143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.119: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8080 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.131: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8080 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.135: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0080 Nov 29 20:07:30.143: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8080 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0081 callID = 0x8002 switch = primary-ni interface = Network Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0081 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '32143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.183: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8081 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.191: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8081 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.195: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0081 Nov 29 20:07:30.203: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8081 Nov 29 20:07:34.139: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:37.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 On Mon, Nov 29, 2010 at 12:04 PM, Randall Crumm randall.cr...@flextronics.com wrote: HI, If you can call OB you still need to make sure your config for IB is correct. You need an IB dial peer and a translation rule to strip down the called number to 3001 HTH Randall From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Rafay Aslam Sent: Monday, November 29, 2010 8:24 AM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Lab 4A Hi I am doing Lab 4A, I
[OSL | CCIE_Voice] CUE license issue
Hello all we have an CUE module on a 2950 router. the maximum # of mailboxes that it supports is 80 we were licensed for 56, I got the pak number and issued the license to upgrade to a total of 80 mailboxes i went to the cli and issue license install ftp://ftpserver/licensefilename reloaded CUE when CUE came back up, i did a show license permanent and the status for mailboxes is 80/80 it doesn't let me add more users, because it says we reached 80/80 users, however we only have 56 users on the system do you know why this is happening ? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Lab 4A
Hi Please find BR2 router configuration, so when I call from PSTN Phone which is connected to PSTN GW, I dial 3432143005 or 32143005 I get fast bussy on PSTN Phone, call never hits BR router which is why I dont see any message in debug isdn q931 on BR2 router. from BR2 Phones ie DN 3005 I am able to dial 911 / 999 / 3432141891 which is a PSTN DN configured on PSTN phone. Just to describe my Lab, Its my home setup, I dont have E1 modules they are been orderd, so I am have configured T1 between PSTN and BR2 for now. Regards Rafay On Mon, Nov 29, 2010 at 4:47 PM, givemeccievoice2...@gmail.com wrote: Hi Rafay, Can you send the configuration from Site C? He was referring to the translation profile applied incoming on the voice-port on R3. It should look something like this: Voice-translation-rule 1 Rule 1 /^32143/ /3/ Or (I see two different called numbers below) Voice translation-rule 1 Rule 1 /^\+3432143/ /3/ Then create the profile and apply to voice-port Voice-translation-profile PSTN-IN Translate called 1 Voice-port 0/0/0:15 Translation-profile incoming PSTN-IN Jeff *From:* ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Rafay Aslam *Sent:* Monday, November 29, 2010 1:22 PM *To:* Randall Crumm *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] Lab 4A Hi Attach is a complete PSNT Config. On Mon, Nov 29, 2010 at 3:12 PM, Randall Crumm randall.cr...@flextronics.com wrote: Can you send your voice translation rule/profile and how it is applied to the voice port? *From:* Rafay Aslam [mailto:rafayc...@gmail.com] *Sent:* Monday, November 29, 2010 12:11 PM *To:* Randall Crumm *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] Lab 4A Hi I have inital configuration loaded from PSTN router, here is debug from PSTN Router, I am calling from PSTN Phone to 3214-3005, so basically I want to see if my translation pattern works on BR2 Router whyic PSTN-WAN# Nov 29 20:07:25.135: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:28.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:30.063: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0080 callID = 0x8001 switch = primary-ni interface = Network Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0080 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '+3432143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.119: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8080 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.131: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8080 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.135: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0080 Nov 29 20:07:30.143: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8080 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0081 callID = 0x8002 switch = primary-ni interface = Network Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0081 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '32143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.183: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8081 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.191: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8081 * Cause i = 0x8081 - Unallocated/unassigned number** *Nov 29 20:07:30.195: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0081 Nov 29 20:07:30.203: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8081 Nov 29 20:07:34.139: ISDN
Re: [OSL | CCIE_Voice] Lab 4A
voice translation-profile 4digitDNIS translate calling 2 This should be translate called 2 for an inbound call Also make a test call to a sccp phone. That way you can see if it a global problem, or a SIP issue. I also see the VLAN 200 and 400 shutdown HTH Randall From: Rafay Aslam [mailto:rafayc...@gmail.com] Sent: Monday, November 29, 2010 3:38 PM To: givemeccievoice2...@gmail.com Cc: Randall Crumm; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Lab 4A Hi Please find BR2 router configuration, so when I call from PSTN Phone which is connected to PSTN GW, I dial 3432143005 or 32143005 I get fast bussy on PSTN Phone, call never hits BR router which is why I dont see any message in debug isdn q931 on BR2 router. from BR2 Phones ie DN 3005 I am able to dial 911 / 999 / 3432141891 which is a PSTN DN configured on PSTN phone. Just to describe my Lab, Its my home setup, I dont have E1 modules they are been orderd, so I am have configured T1 between PSTN and BR2 for now. Regards Rafay On Mon, Nov 29, 2010 at 4:47 PM, givemeccievoice2...@gmail.com wrote: Hi Rafay, Can you send the configuration from Site C? He was referring to the translation profile applied incoming on the voice-port on R3. It should look something like this: Voice-translation-rule 1 Rule 1 /^32143/ /3/ Or (I see two different called numbers below) Voice translation-rule 1 Rule 1 /^\+3432143/ /3/ Then create the profile and apply to voice-port Voice-translation-profile PSTN-IN Translate called 1 Voice-port 0/0/0:15 Translation-profile incoming PSTN-IN Jeff From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Rafay Aslam Sent: Monday, November 29, 2010 1:22 PM To: Randall Crumm Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Lab 4A Hi Attach is a complete PSNT Config. On Mon, Nov 29, 2010 at 3:12 PM, Randall Crumm randall.cr...@flextronics.com wrote: Can you send your voice translation rule/profile and how it is applied to the voice port? From: Rafay Aslam [mailto:rafayc...@gmail.com] Sent: Monday, November 29, 2010 12:11 PM To: Randall Crumm Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Lab 4A Hi I have inital configuration loaded from PSTN router, here is debug from PSTN Router, I am calling from PSTN Phone to 3214-3005, so basically I want to see if my translation pattern works on BR2 Router whyic PSTN-WAN# Nov 29 20:07:25.135: ISDN Se0/1/0:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:28.499: ISDN Se0/0/1:23 Q931: Ux_DLRelInd: DL_REL_IND received from L2 Nov 29 20:07:30.063: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0080 callID = 0x8001 switch = primary-ni interface = Network Nov 29 20:07:30.067: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0080 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '+3432143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.119: ISDN Se0/0/0:23 Q931: RX - CALL_PROC pd = 8 callref = 0x8080 Channel ID i = 0xA98381 Exclusive, Channel 1 Nov 29 20:07:30.131: ISDN Se0/0/0:23 Q931: RX - DISCONNECT pd = 8 callref = 0x8080 Cause i = 0x8081 - Unallocated/unassigned number Nov 29 20:07:30.135: ISDN Se0/0/0:23 Q931: TX - RELEASE pd = 8 callref = 0x0080 Nov 29 20:07:30.143: ISDN Se0/0/0:23 Q931: RX - RELEASE_COMP pd = 8 callref = 0x8080 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is 0x0 0x0, Calling num 999 Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: Sending SETUP callref = 0x0081 callID = 0x8002 switch = primary-ni interface = Network Nov 29 20:07:30.155: ISDN Se0/0/0:23 Q931: TX - SETUP pd = 8 callref = 0x0081 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Display i = 'Emergency Services' Calling Party Number i = 0x0080, '999' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '32143005' Plan:Unknown, Type:Unknown Nov 29 20:07:30.183: ISDN Se0/0/0:23 Q931: RX -
Re: [OSL | CCIE_Voice] SCCP- CUCM -GK-CME-SIP Phone call failing
Hello Cris/Jeff Issue is sorted out. codec g729 was all ready configured. Under dn , call forward noan is set to unity express which works on g711ulaw which i had missed. registered trancoder and all worked ! thx for help ! Regards, MJ On Tue, Nov 30, 2010 at 1:24 AM, Cristobal Priego cristobalpri...@gmail.com wrote: have you check the codec ? i think that from sccp -cucm is G.729 CME-SIP only supports G.711 if that's the case register a transcoder on the cme 2010/11/29 Mritunjay Kumar mjs...@gmail.com Hi All , call flow SCCP- CUCM -GK-CME-SIP I enabled inbound faststart and call from SIP from CME to sccp phone of cucm is working fine. but when call is placed in opposite direction , after 1st ring , call is getting disconnected. I enabled outbound faststart with cucm MTP in MRGL but no luck . Any idea ? Regards, MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
