[Elecraft] K2 S-meter calibration (CW-CWRV-USB-LSB) ?
Hi K2 builders; I do have calibrate my S-meter following exactly what is tell in the building manual. I do have done this allignement CW normal mode. What I see while switching between CW reverse and USB and LSB mode is that the right led indication does not indicate most right on other modes ??? I see a little difference in S-meter indicaton bewteen CW normal and the 3 other modes ?? The S-meter indicaton is dropping one led from right. The most right led indication is done with RF control fully counter clockwise of course. Is this normal,I do have allign my filters and BFO settings all correctly. Yes I now,I am talking about details now,and what I see while playing with my new toy hi. Next days I start to build my KPA100 unit. Great building kit for sure... Regards Jean ON4AEF. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Noisy RX redux
Hi Mike, For those wondering what Mike found. There are two ways to go. A complete DSP board swap or a DSP board modification. K3DSPUPGD for $109.95 (this is the board swap) or K3DSPLPF for $39.95 (this is the board mod) Both items can be found here: http://www.elecraft.com/order_form_parts.htm Serial numbers might not be the best clue for those buying a previously owned radio. The previous owner might have already made the improvement. 73, Mike K2MK Mike Reublin wrote I found the mod. On Jul 4, 2013, at 6:38 PM, Mike Reublin lt; nf4l@ gt; wrote: On Jul 4, 2013, at 5:47 PM, Mike Reublin lt; nf4l@ gt; wrote: Shortly after I got K3 3935 in Sept. of '09, the furor over noisy RX kinda peaked, and the result was a board swap. A friend just bought a used K3 with a slightly earlier SN, and the RX background is very harsh and sharp sounding. We both came to Elecraft from a PRO II/III where the background in an A/B comparison is a soft swhsh. I'd like to check and see if it has the same mod, but I've slept since then and cannot remember what the mod was called, or how to check for it. A tour of the mods page didn't kick my recaller into gear. A related wish: List the serial number when a mod goes into production. n unrelated wish: HAPPY 4th! 73, Mike NF4L -- View this message in context: http://elecraft.365791.n2.nabble.com/Noisy-RX-redux-tp7576283p7576301.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 Receive Noise
Try going into the menu and turning on the RX I/Q out. I noticed on my kx3 with the latest firmware, there is a sharp hum and audio distortion while the RX I/Q out is disabled. The noise is so piercing I can't use headphones with it. Turning on the RX I/Q instantly kills the unwanted receiver noise. -- View this message in context: http://elecraft.365791.n2.nabble.com/KX3-Receive-Noise-tp7574188p7576302.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] FS Elecraft (Heil) Boom Headset
For sale as new used 3 times in the box Elecraft Boom Headset $140 shipped lower USA, other places will be at actual cost. Thx for looking. 73, Fred/N0AZZ K3 Ser # 6730--KX3 # 2573--K2/100 # 6470-KAT100 P3/SVGA--KPA500--KAT500--W2 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] DSP board rev level
Is it possible to determine the rev code of the DSP board without removing it? 73, Mike NF4L __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] DSP board rev level
You only have to remove the front panel *assembly* to be able to see the label.. It cannot be seen with the K3 fully assembled. 73, Don W3FPR On 7/5/2013 8:34 AM, Mike Reublin wrote: Is it possible to determine the rev code of the DSP board without removing it? 73, Mike NF4L __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 S-meter calibration (CW-CWRV-USB-LSB) ?
Jean, You can adjust the CAL S HI menu in CW reverse or LSB or USB to compensate for that discrepancy. If you have a signal generator that produces a 50 microvolt (-73 dBm) signal, use that to adjust the CAL S-HI menu parameter. 73, Don W3FPR On 7/5/2013 4:30 AM, Behiels JeanPierre wrote: Hi K2 builders; I do have calibrate my S-meter following exactly what is tell in the building manual. I do have done this allignement CW normal mode. What I see while switching between CW reverse and USB and LSB mode is that the right led indication does not indicate most right on other modes ??? I see a little difference in S-meter indicaton bewteen CW normal and the 3 other modes ?? The S-meter indicaton is dropping one led from right. The most right led indication is done with RF control fully counter clockwise of course. Is this normal,I do have allign my filters and BFO settings all correctly. Yes I now,I am talking about details now,and what I see while playing with my new toy hi. Next days I start to build my KPA100 unit. Great building kit for sure... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K1 TX output low on 2 of 4 bands
My K1 (#1066, built 11 years ago) is a four-bander with ATU and internal battery pack. In May I built an Elecraft W1 wattmeter and used it to discover that my TX output (When Out in the menu is set to 7.0W) is only 1.2W on 15 meters. At that time, all other bands showed an output of 5W. However, last night, after an afternoon of using my K1 while fruitlessly trying to tune up a new antenna, I noticed that the output on 20 meters was also now down, measuring 1.5W. I strongly suspect that a component failed due to TX'ing into high SWR while trying to adjust the antenna I was working on. 40 and 30 meters still seem to be okay. (My guess is that 15 is low for the same reason--I just didn't discover it in a timely fashion like I did with 20 meters). So, anybody have a suggestion for where to start with troubleshooting? Should I suspect the filter board? Any components in particular? Thanks in advance for any morsels of wisdom - Dave NK0E __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K1 TX output low on 2 of 4 bands
Never mind. It was operator error. Helps to read the instructions. Self-administering dope slap now... 73, Dave NK0E On 7/5/2013 7:55 AM, David Ek wrote: My K1 (#1066, built 11 years ago) is a four-bander with ATU and internal battery pack. In May I built an Elecraft W1 wattmeter and used it to discover that my TX output (When Out in the menu is set to 7.0W) is only 1.2W on 15 meters. At that time, all other bands showed an output of 5W. However, last night, after an afternoon of using my K1 while fruitlessly trying to tune up a new antenna, I noticed that the output on 20 meters was also now down, measuring 1.5W. I strongly suspect that a component failed due to TX'ing into high SWR while trying to adjust the antenna I was working on. 40 and 30 meters still seem to be okay. (My guess is that 15 is low for the same reason--I just didn't discover it in a timely fashion like I did with 20 meters). So, anybody have a suggestion for where to start with troubleshooting? Should I suspect the filter board? Any components in particular? Thanks in advance for any morsels of wisdom - Dave NK0E __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K1 TX output low on 2 of 4 bands
Dave/NK0E wrote: My K1 (#1066, built 11 years ago) is a four-bander with ATU and internal battery pack. What power supply were you using when you measured the output power that you report below? In May I built an Elecraft W1 wattmeter and used it to discover that my TX output (When Out in the menu is set to 7.0W) is only 1.2W on 15 meters. At that time, all other bands showed an output of 5W. However, last night, after an afternoon of using my K1 while fruitlessly trying to tune up a new antenna, I noticed that the output on 20 meters was also now down, measuring 1.5W. I strongly suspect that a component failed due to TX'ing into high SWR while trying to adjust the antenna I was working on. This is extremely unlikely. Any RF board component failure would affect all four bands, not just 20m and 15m. During use of a very poor antenna load, the most common result is shorting of the RF board D19 Zener that is across the RF-Q7 PA transistor, which is what D19 is designed to do to protect RF-Q7 (and usually destroy itself in the process). This definitely has NOT happened to your K1. Rest assured then that nothing was hurt on your K1 during your antenna tuning efforts. When some bands still function well, but others do not, it is a certainty that the problem is on the filter board. You have an older K1, and possibly an early KFL1-4 filter board. The 16 trimmer capacitors that are on the KFL1-4 were originally white-body capacitors that were very prone to spontaneously changing their effective value. A couple of years after the KFL1-4 was introduced, Elecraft changed all 16 trimmers to a much more stable design with a light blue body. Look at the four rows of trimmer capacitors on your KFL1-4, which are easily observed from the back of the K1 even without removing the KAT1. If they they do not have light blue plastic bodies, then you have the old troublesome original trimmers in place. You'll need to get the replacement trimmers and install them. Those are almost certainly the source of your problems. OTOH, if you have the newer blue-body trimmers, you will still want to re-align your KFL1-4 to restore full output. In fact, you'll want to do that if you have white trimmers, just to verify that output can be restored in the interim before change out. When I still had those old trimmers on mine, I needed to re-peak 15m and 20m on my KFL1-4 every few months due to the drop in output power I observed. So did a lot of other people. After such results, Elecraft supplied a set of 16 blue-body replacements. It was *not* a lot of fun removing 16 trimmers and replacing them, but it was worth it. I recently re-peaked my KFL1-4 after more than eight years since last performed, and found essentially no pre-peaking degradation. 73, Mike / KK5F __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K1 TX output low on 2 of 4 bands
Mike, I didn't have the K1 internal ATU switched out like I thought I did. All is well (except for my embarrassment...). 73, Dave NK0E On 7/5/2013 8:57 AM, Mike Morrow wrote: Dave/NK0E wrote: My K1 (#1066, built 11 years ago) is a four-bander with ATU and internal battery pack. What power supply were you using when you measured the output power that you report below? In May I built an Elecraft W1 wattmeter and used it to discover that my TX output (When Out in the menu is set to 7.0W) is only 1.2W on 15 meters. At that time, all other bands showed an output of 5W. However, last night, after an afternoon of using my K1 while fruitlessly trying to tune up a new antenna, I noticed that the output on 20 meters was also now down, measuring 1.5W. I strongly suspect that a component failed due to TX'ing into high SWR while trying to adjust the antenna I was working on. This is extremely unlikely. Any RF board component failure would affect all four bands, not just 20m and 15m. During use of a very poor antenna load, the most common result is shorting of the RF board D19 Zener that is across the RF-Q7 PA transistor, which is what D19 is designed to do to protect RF-Q7 (and usually destroy itself in the process). This definitely has NOT happened to your K1. Rest assured then that nothing was hurt on your K1 during your antenna tuning efforts. When some bands still function well, but others do not, it is a certainty that the problem is on the filter board. You have an older K1, and possibly an early KFL1-4 filter board. The 16 trimmer capacitors that are on the KFL1-4 were originally white-body capacitors that were very prone to spontaneously changing their effective value. A couple of years after the KFL1-4 was introduced, Elecraft changed all 16 trimmers to a much more stable design with a light blue body. Look at the four rows of trimmer capacitors on your KFL1-4, which are easily observed from the back of the K1 even without removing the KAT1. If they they do not have light blue plastic bodies, then you have the old troublesome original trimmers in place. You'll need to get the replacement trimmers and install them. Those are almost certainly the source of your problems. OTOH, if you have the newer blue-body trimmers, you will still want to re-align your KFL1-4 to restore full output. In fact, you'll want to do that if you have white trimmers, just to verify that output can be restored in the interim before change out. When I still had those old trimmers on mine, I needed to re-peak 15m and 20m on my KFL1-4 every few months due to the drop in output power I observed. So did a lot of other people. After such results, Elecraft supplied a set of 16 blue-body replacements. It was *not* a lot of fun removing 16 trimmers and replacing them, but it was worth it. I recently re-peaked my KFL1-4 after more than eight years since last performed, and found essentially no pre-peaking degradation. 73, Mike / KK5F __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 Antenna Tolerance
Hello Tom, I've just finished my K2 bare bones, and would like to get on the air. What SWR will the finals tolerate without harm? I'm using a ground mounted trap vertical I have used my old K2 (#01118, modified for 5 watts output) also without an antenna, but without deletions of the finals, so the SWR was infinite. But if you use the upper output limit of your K2 this operation mode could be deadly. -- 73/72 de Ingo, DK3RED - Don't forget: the fun is the power! www.qrp4fun.de - dk3...@qrp4fun.de __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] OT P3 video of RFI, ideas?
This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. When it is there in the 20-meter band there are siblings almost as strong at the following frequencies: 13.975 14.032-the recording 14.126 14.220 14.282 14.469 In addition, there are less strong signals that follow the pulsation; one is visible on the recording at 14000 (far left on the P3). They are also in the 17 meter band. They are not in the 15 meter band or above. I have pulled the big switch and it is still there on battery power. My suspension is a neighbor with plasma television. Is this what plasma TV looks like? It is directional in nature and the strongest signal comes from a 40-degree heading, roughly Europe from my location, or to a cluster of homes to my northeast. 73, Bill AK5X Bill Hammond wham...@aol.com Bill Hammond-AK5X a...@mac.com a...@sbcglobal.net K3 #69 P3 #817 KPA500 # 149 K2/100 #4637 K1 #2033 KX1 #1023 KX3 #583 W2 T1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
Bill, We have a *^%$$ Samsung 63 plasma TV in the family room. When it is turned on, that's exactly what it looks like on my P3. When I'm on the air and someone turns on that piece of crap, I know in an instant. Jim / W6JHB On Friday, Jul 5, 2013, at Friday, 9:29 AM, Bill Hammond wrote: This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. When it is there in the 20-meter band there are siblings almost as strong at the following frequencies: 13.975 14.032-the recording 14.126 14.220 14.282 14.469 In addition, there are less strong signals that follow the pulsation; one is visible on the recording at 14000 (far left on the P3). They are also in the 17 meter band. They are not in the 15 meter band or above. I have pulled the big switch and it is still there on battery power. My suspension is a neighbor with plasma television. Is this what plasma TV looks like? It is directional in nature and the strongest signal comes from a 40-degree heading, roughly Europe from my location, or to a cluster of homes to my northeast. 73, Bill AK5X Bill Hammond wham...@aol.com Bill Hammond-AK5X a...@mac.com a...@sbcglobal.net K3 #69 P3 #817 KPA500 # 149 K2/100 #4637 K1 #2033 KX1 #1023 KX3 #583 W2 T1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
I thought plasma TVs were outlawed some time ago. Obviously there are still plenty of them around. I see occasional interferers but at a lower amplitude - must be neighbors' TVs. 73, matt W6NIA On Fri, 05 Jul 2013 09:41:57 -0700, you wrote: Bill, We have a *^%$$ Samsung 63 plasma TV in the family room. When it is turned on, that's exactly what it looks like on my P3. When I'm on the air and someone turns on that piece of crap, I know in an instant. Jim / W6JHB On Friday, Jul 5, 2013, at Friday, 9:29 AM, Bill Hammond wrote: This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. When it is there in the 20-meter band there are siblings almost as strong at the following frequencies: 13.975 14.032-the recording 14.126 14.220 14.282 14.469 In addition, there are less strong signals that follow the pulsation; one is visible on the recording at 14000 (far left on the P3). They are also in the 17 meter band. They are not in the 15 meter band or above. I have pulled the big switch and it is still there on battery power. My suspension is a neighbor with plasma television. Is this what plasma TV looks like? It is directional in nature and the strongest signal comes from a 40-degree heading, roughly Europe from my location, or to a cluster of homes to my northeast. 73, Bill AK5X Bill Hammond wham...@aol.com Bill Hammond-AK5X a...@mac.com a...@sbcglobal.net K3 #69 P3 #817 KPA500 # 149 K2/100 #4637 K1 #2033 KX1 #1023 KX3 #583 W2 T1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
Jim, have you tried suppressing that garbage with ferrites on the Samsung power cord or various signal cables? /Rick On Fri, Jul 5, 2013 at 9:41 AM, Jim Bennett w6...@mac.com wrote: Bill, We have a *^%$$ Samsung 63 plasma TV in the family room. When it is turned on, that's exactly what it looks like on my P3. When I'm on the air and someone turns on that piece of crap, I know in an instant. Jim / W6JHB On Friday, Jul 5, 2013, at Friday, 9:29 AM, Bill Hammond wrote: This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. -- Rick Tavan N6XI Truckee, CA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
I'm wondering if this is a serious comment? Go to any Best Buy, and you'll find they are far from illegal. 73, Scott, N9AA On 7/5/13 12:54 PM, Matt Zilmer wrote: I thought plasma TVs were outlawed some time ago. Obviously there are still plenty of them around. I see occasional interferers but at a lower amplitude - must be neighbors' TVs. 73, matt W6NIA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
Rick - I put a couple big clamp-on's on the power cord. No help. The only other cable going to that TV is a heavily shielded HDMI cable from the Denon A/V unit. From what I understand, the RFI is generated in the plasma cell area, and not on any cables. I may be mistaken, but I believe the best way to suppress plasma TV generated RFI is with a 12-gauge shotgun. And, believe me, if (1) it was legal, and (2) not so expensive - I'do just that to ours!!! :-) :-) And, no - don't do that to your neighbor's TV!! Actually, that Samsung TV gets little use these days. Our main TV is a 65 Panasonic Viera plasma set that surprisingly generates no RFI crud. On Friday, Jul 5, 2013, at Friday, 10:12 AM, Rick Tavan N6XI wrote: Jim, have you tried suppressing that garbage with ferrites on the Samsung power cord or various signal cables? /Rick On Fri, Jul 5, 2013 at 9:41 AM, Jim Bennett w6...@mac.com wrote: Bill, We have a *^%$$ Samsung 63 plasma TV in the family room. When it is turned on, that's exactly what it looks like on my P3. When I'm on the air and someone turns on that piece of crap, I know in an instant. Jim / W6JHB On Friday, Jul 5, 2013, at Friday, 9:29 AM, Bill Hammond wrote: This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. -- Rick Tavan N6XI Truckee, CA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
The plasmas were not really 'outlawed' - but California made sales there a problem because they are rather inefficient users of electrical power. (As in close to a KW to create a picture on early models.) - That said, their picture is usually vastly superior to the LCD sets, even those with LED backlights. KK4QDZ - Now with Extra Class Priv's, and a tiny KX3 to enjoy them! From: Matt Zilmer mzil...@verizon.net To: Jim Bennett w6...@mac.com Cc: Elecraft Reflector Elecraft@mailman.qth.net Sent: Friday, July 5, 2013 12:54 PM Subject: Re: [Elecraft] OT P3 video of RFI, ideas? I thought plasma TVs were outlawed some time ago. Obviously there are still plenty of them around. I see occasional interferers but at a lower amplitude - must be neighbors' TVs. 73, matt W6NIA On Fri, 05 Jul 2013 09:41:57 -0700, you wrote: Bill, We have a *^%$$ Samsung 63 plasma TV in the family room. When it is turned on, that's exactly what it looks like on my P3. When I'm on the air and someone turns on that piece of crap, I know in an instant. Jim / W6JHB On Friday, Jul 5, 2013, at Friday, 9:29 AM, Bill Hammond wrote: This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. When it is there in the 20-meter band there are siblings almost as strong at the following frequencies: 13.975 14.032-the recording 14.126 14.220 14.282 14.469 In addition, there are less strong signals that follow the pulsation; one is visible on the recording at 14000 (far left on the P3). They are also in the 17 meter band. They are not in the 15 meter band or above. I have pulled the big switch and it is still there on battery power. My suspension is a neighbor with plasma television. Is this what plasma TV looks like? It is directional in nature and the strongest signal comes from a 40-degree heading, roughly Europe from my location, or to a cluster of homes to my northeast. 73, Bill AK5X Bill Hammond wham...@aol.com Bill Hammond-AK5X a...@mac.com a...@sbcglobal.net K3 #69 P3 #817 KPA500 # 149 K2/100 #4637 K1 #2033 KX1 #1023 KX3 #583 W2 T1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
Bill, I have a 50 inch Panasonic plasma and when it is on, lower bands 40 meters and below are near useless. It causes some problems for me on 20 meters and up but it gets less as the bands go up. My P3 display is similar to yours. Otherwise it’s a great TV, great picture. I have tried several things but only thing that has helped, especially on 20 meters and above is to move ham antenna further away from my house. As best I can tell RFI comes from the screen and not the cables or the power cable. If anyone finds a better solution, other than shotgun or not using it, please let me know. 73 good luck Emory WM3M -Original Message- From: Bill Hammond Sent: Friday, July 05, 2013 12:29 PM To: Elecraft Reflector Subject: [Elecraft] OT P3 video of RFI, ideas? This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. When it is there in the 20-meter band there are siblings almost as strong at the following frequencies: 13.975 14.032-the recording 14.126 14.220 14.282 14.469 In addition, there are less strong signals that follow the pulsation; one is visible on the recording at 14000 (far left on the P3). They are also in the 17 meter band. They are not in the 15 meter band or above. I have pulled the big switch and it is still there on battery power. My suspension is a neighbor with plasma television. Is this what plasma TV looks like? It is directional in nature and the strongest signal comes from a 40-degree heading, roughly Europe from my location, or to a cluster of homes to my northeast. 73, Bill AK5X Bill Hammond wham...@aol.com Bill Hammond-AK5X a...@mac.com a...@sbcglobal.net K3 #69 P3 #817 KPA500 # 149 K2/100 #4637 K1 #2033 KX1 #1023 KX3 #583 W2 T1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
Just a comment to say I have read numerous reports of RFI being caused by plasma TV's and I am wondering how the problem escaped the FCC? Dick, n0ce __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
In the UK there has been a great deal of interference caused by plasma screens. The QRM is radiated by the screen and gets worse with age as the power to the backlight increases to compensate for reducing emissivity. Recently Panasonic, the main culprit, have been replacing plasmas with their latest LCD model that have much better pictures and no rfi. Current LCD models now have much improved performance and have better pictures that the plasmas that are now being phased out. A campaign has been waged by concerned amateurs and details can be found at http://www.ukqrm.org.uk/ Best of luck 73 Peter G3SMT From: WM3M w...@live.com To: Bill Hammond wham...@aol.com; Elecraft Reflector Elecraft@mailman.qth.net Sent: Friday, 5 July 2013, 17:45 Subject: Re: [Elecraft] OT P3 video of RFI, ideas? Bill, I have a 50 inch Panasonic plasma and when it is on, lower bands 40 meters and below are near useless. It causes some problems for me on 20 meters and up but it gets less as the bands go up. My P3 display is similar to yours. Otherwise it’s a great TV, great picture. I have tried several things but only thing that has helped, especially on 20 meters and above is to move ham antenna further away from my house. As best I can tell RFI comes from the screen and not the cables or the power cable. If anyone finds a better solution, other than shotgun or not using it, please let me know. 73 good luck Emory WM3M -Original Message- From: Bill Hammond Sent: Friday, July 05, 2013 12:29 PM To: Elecraft Reflector Subject: [Elecraft] OT P3 video of RFI, ideas? This is a bit off topic but perhaps other P3 users on this reflector have encountered this RFI and have some idea where it comes from and perhaps a remedy? There must be a couple of thousand P3 users on this reflector. The below is a recording and includes sound of this nasty bit of pulsating RF. Video recording: http://www.flickr.com/photos/ak5x/9214448105/ It is not always there. When it is there in the 20-meter band there are siblings almost as strong at the following frequencies: 13.975 14.032-the recording 14.126 14.220 14.282 14.469 In addition, there are less strong signals that follow the pulsation; one is visible on the recording at 14000 (far left on the P3). They are also in the 17 meter band. They are not in the 15 meter band or above. I have pulled the big switch and it is still there on battery power. My suspension is a neighbor with plasma television. Is this what plasma TV looks like? It is directional in nature and the strongest signal comes from a 40-degree heading, roughly Europe from my location, or to a cluster of homes to my northeast. 73, Bill AK5X Bill Hammond wham...@aol.com Bill Hammond-AK5X a...@mac.com a...@sbcglobal.net K3 #69 P3 #817 KPA500 # 149 K2/100 #4637 K1 #2033 KX1 #1023 KX3 #583 W2 T1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
The biggest issue is that the RF is generated in the plasma display itself and it is radiated directly through the screen (which is transparent to RF). 73, Ron AC7AC -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of WM3M Sent: Friday, July 05, 2013 10:45 AM To: Bill Hammond; Elecraft Reflector Subject: Re: [Elecraft] OT P3 video of RFI, ideas? Bill, I have a 50 inch Panasonic plasma and when it is on, lower bands 40 meters and below are near useless. It causes some problems for me on 20 meters and up but it gets less as the bands go up. My P3 display is similar to yours. Otherwise it’s a great TV, great picture. I have tried several things but only thing that has helped, especially on 20 meters and above is to move ham antenna further away from my house. As best I can tell RFI comes from the screen and not the cables or the power cable. If anyone finds a better solution, other than shotgun or not using it, please let me know. 73 good luck Emory WM3M __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT - anyone have experience with effects of metal roofs on antenna performace?
I had verticals on concrete, roof shingle and metal roofs. Always radials lying on top. The metal roof was the best by far. One way to find out how much the roof is affecting the performance of a beam is to look at SWR changes as the antenna is rotating. Ignacy, NO9E -- View this message in context: http://elecraft.365791.n2.nabble.com/OT-anyone-have-experience-with-effects-of-metal-roofs-on-antenna-performace-tp7576265p7576322.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT - anyone have experience with effects of metal roofs on antenna performace?
SWR is a pretty coarse indication of interaction. Interactions can change directional antenna F/B and F/S ratio by 6-10 db easily (assuming you have it in the first place) and hardly affect SWR. At least, this is my experience from antenna modeling. However, we have to live with the hands we're dealt. Without any field strength measurements or calculations, one probably won't detect much. Ignorance is bliss. 73 de Brian/K3KO On 7/5/2013 20:13, Ignacy wrote: I had verticals on concrete, roof shingle and metal roofs. Always radials lying on top. The metal roof was the best by far. One way to find out how much the roof is affecting the performance of a beam is to look at SWR changes as the antenna is rotating. Ignacy, NO9E -- View this message in context: http://elecraft.365791.n2.nabble.com/OT-anyone-have-experience-with-effects-of-metal-roofs-on-antenna-performace-tp7576265p7576322.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html - No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.2242 / Virus Database: 3204/5967 - Release Date: 07/05/13 - No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.2242 / Virus Database: 3204/5967 - Release Date: 07/05/13 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT - anyone have experience with effects of metal roofs on antenna performace?
I remember the toughest class was antenna theory. As an undergrad EE student, I believed that this class would kill my plan to be an EE. I got a 25 (out of 100)! No bragging, it was the highest grade. They graded on a curve. My prof was a world renown antenna expert. He liked to @#* with us. So if anyone figures out this antenna stuff email me __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Win4K3Suite version 1.10 is now available
Version 1.10 of Win4K3Suite is now available. New features include support for Fixed and Tracking mode for the P3 as well as general P3 control improvements. Support for Logic 9 logging program is now added. Tested logging programs include DX4Win, DXKeeper, HRD 6 and 5, and Logger32, Version 1.1 brings big performance improvements for both the client and the server. Software is available from VA2FSQ.COM Watch the video...http://m.youtube.com/#/watch?v=Api2nomzg3Udesktop_uri=%2Fwatch%3Fv%3DApi2nomzg3U Sent from my iPhone __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT - anyone have experience with effects of metalroofs on antenna performace?
I was just reviewing my copy of Balanis and remembered the grueling effort of the class. I took it in grad school with a crazy Greek professor who worked with Balanis. He wound up being my thesis advisor :) Kevin. KD5ONS On 7/5/2013 1:54 PM, george fritkin wrote: I remember the toughest class was antenna theory. As an undergrad EE student, I believed that this class would kill my plan to be an EE. I got a 25 (out of 100)! No bragging, it was the highest grade. They graded on a curve. My prof was a world renown antenna expert. He liked to @#* with us. So if anyone figures out this antenna stuff email me __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT - anyone have experience with effects of metalroofs on antenna performace?
Ah, memories … I took an antenna class from Balanis, and we used photo copies of his fledgling book, acting as proofers. He was my senior EE project advisor as well. Quite a character. I wish I still remembered a fraction of what I knew then. Hi hi. Phil, NS7P On Jul 5, 2013, at 3:11 PM, kevinr kev...@coho.net wrote: I was just reviewing my copy of Balanis and remembered the grueling effort of the class. I took it in grad school with a crazy Greek professor who worked with Balanis. He wound up being my thesis advisor :) Kevin. KD5ONS On 7/5/2013 1:54 PM, george fritkin wrote: I remember the toughest class was antenna theory. As an undergrad EE student, I believed that this class would kill my plan to be an EE. I got a 25 (out of 100)! No bragging, it was the highest grade. They graded on a curve. My prof was a world renown antenna expert. He liked to @#* with us. So if anyone figures out this antenna stuff email me __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 es AIRMAIL
I've been told that the application AIRMAIL does notinterface the Elecraft to control frequency and transmission. A recent version of AIRMAIL, v 3.4.062, lists the K2 and K3 in the setup menu. I'd like a report of the experience of any who have tried interfacing a K3 to this version of AIRMAIL and using the rig control function. 73 de Red, WOXW __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT P3 video of RFI, ideas?
Contact Panasonic and remind them that the TV was certified as Part 15 compliant, and that if they cannot fix it you will contact the FCC and report their failure to maintain part 15 compliance. That's about the only thing you can do unless it is new and is still under the 30 day return limit. Plasma TV's and their manufacturers are evil. 73, Tom Amateur Radio Operator N5GE ARRL Lifetime Member QCWA Lifetime Member On Fri, 5 Jul 2013 12:02:48 -0700, Ron D'Eau Claire r...@cobi.biz wrote: The biggest issue is that the RF is generated in the plasma display itself and it is radiated directly through the screen (which is transparent to RF). 73, Ron AC7AC -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of WM3M Sent: Friday, July 05, 2013 10:45 AM To: Bill Hammond; Elecraft Reflector Subject: Re: [Elecraft] OT P3 video of RFI, ideas? Bill, I have a 50 inch Panasonic plasma and when it is on, lower bands 40 meters and below are near useless. It causes some problems for me on 20 meters and up but it gets less as the bands go up. My P3 display is similar to yours. Otherwise its a great TV, great picture. I have tried several things but only thing that has helped, especially on 20 meters and above is to move ham antenna further away from my house. As best I can tell RFI comes from the screen and not the cables or the power cable. If anyone finds a better solution, other than shotgun or not using it, please let me know. 73 good luck Emory WM3M __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 es AIRMAIL
I would like to know the answer too...I will keep alert 73 Gary On 6 July 2013 09:47, WO0W w...@acegroup.cc wrote: I've been told that the application AIRMAIL does notinterface the Elecraft to control frequency and transmission. A recent version of AIRMAIL, v 3.4.062, lists the K2 and K3 in the setup menu. I'd like a report of the experience of any who have tried interfacing a K3 to this version of AIRMAIL and using the rig control function. 73 de Red, WOXW __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecrafthttp://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htmhttp://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- *Gary - VK1ZZ Skype: Gary.VK1ZZ http://www.qsl.net/vk1zz Motorhome Portable The Shack* *Elecraft K3 P3 Panadapter KPA500FT KAT500FT** * __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Custom 700 Hz 8-Pole INRAD Filters--You Should Get in Queue!
Hi Everyone, I recently purchased and installed the 700 Hz Custom INRAD filter from Gary-KI4GGX of www.unpcbs.com. In the nearly two weeks that I have had this filter installed in my K3, it has become my primary CW filter for this rig. I am not a contester but rather a search and pounce DXer for many years now (35+). My first rig as a novice was a Heath HW-8 in 1977. It was a QRP CW rig running 2-3w CW with an audio filter at 750Kz. I worked 38 countries with a dipole with that rig. It taught me to learn to listen for CW DX using a broad filter bandwidth compared to most of the standard bandwidths used these days. I have been using an INRAD 8 pole 500 Hz CW filter in my K3 since I got it in 2008. But I had been thinking about Gary's 700 Hz filter for a while now and I finally decided to take the plunge two weeks ago. For me this had turned out to be the perfect CW filter. I find myself using it exclusively now in all but the very most difficult situations. (Remember I do not contest.) It allows me to cruise the CW bands from a wider perspective helping me to gain a more macro-orientation to what's on the CW bands and making me use my brain more to differentiate between the CW signals I hear. It's a very comfortable filter to listen to. For me this filter is a keeper here for sure. As for Gary and unpcbs, both remind me of an extension of Elecraft. Excellent quality product with superior service on top of that. If you are thinking of pre-ordering with Gary for an upcoming INRAD Customer 700 Hz filter batch, I can highly recommend that you do so. I really like this filter. My $.02 73 de N1LQ-Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 es AIRMAIL
I use RMS express with my K3 KX3, it's an up dated version of Airmail with only a couple of minor problems. The developers are working on these problems. I have read that Airmail will not have any further bug fixes or updates. John Hendricks K7JLT On Jul 5, 2013, at 18:15, Gary Gregory vk1zzg...@gmail.com wrote: I would like to know the answer too...I will keep alert 73 Gary On 6 July 2013 09:47, WO0W w...@acegroup.cc wrote: I've been told that the application AIRMAIL does notinterface the Elecraft to control frequency and transmission. A recent version of AIRMAIL, v 3.4.062, lists the K2 and K3 in the setup menu. I'd like a report of the experience of any who have tried interfacing a K3 to this version of AIRMAIL and using the rig control function. 73 de Red, WOXW __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecrafthttp://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htmhttp://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- *Gary - VK1ZZ Skype: Gary.VK1ZZ http://www.qsl.net/vk1zz Motorhome Portable The Shack* *Elecraft K3 P3 Panadapter KPA500FT KAT500FT** * __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 es AIRMAIL
Airmail is one software and RMS express is made by the Winlink group. I use RMS express with my K3 and my K2 and KX3. It works fine business on Winmor. Hope that helps. Thanks Gerald - KC6CNN On Jul 5, 2013 9:12 PM, K7JLTextra k7jltex...@gmail.com wrote: I use RMS express with my K3 KX3, it's an up dated version of Airmail with only a couple of minor problems. The developers are working on these problems. I have read that Airmail will not have any further bug fixes or updates. John Hendricks K7JLT On Jul 5, 2013, at 18:15, Gary Gregory vk1zzg...@gmail.com wrote: I would like to know the answer too...I will keep alert 73 Gary On 6 July 2013 09:47, WO0W w...@acegroup.cc wrote: I've been told that the application AIRMAIL does notinterface the Elecraft to control frequency and transmission. A recent version of AIRMAIL, v 3.4.062, lists the K2 and K3 in the setup menu. I'd like a report of the experience of any who have tried interfacing a K3 to this version of AIRMAIL and using the rig control function. 73 de Red, WOXW __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecraft http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htm http://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- *Gary - VK1ZZ Skype: Gary.VK1ZZ http://www.qsl.net/vk1zz Motorhome Portable The Shack* *Elecraft K3 P3 Panadapter KPA500FT KAT500FT** * __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 es AIRMAIL
NAVMARCORMARS (Navy Marine Corps MARS) uses RMS Express with Winmor for MARS message traffic. It works very well on HF AND Winmor TelNet. I use it with a K3 with NO problems. It supports K3 interfacing for rig control. If HF communications are poor due to solar storms, etc., it can be used to send messages via TelNet. NNN0KYN NAVMARCORMARS 73, Tom Amateur Radio Operator N5GE Licensed since 1976 ARRL Lifetime Member QCWA Lifetime Member On Fri, 5 Jul 2013 19:12:14 -0700, K7JLTextra k7jltex...@gmail.com wrote: I use RMS express with my K3 KX3, it's an up dated version of Airmail with only a couple of minor problems. The developers are working on these problems. I have read that Airmail will not have any further bug fixes or updates. John Hendricks K7JLT On Jul 5, 2013, at 18:15, Gary Gregory vk1zzg...@gmail.com wrote: I would like to know the answer too...I will keep alert 73 Gary On 6 July 2013 09:47, WO0W w...@acegroup.cc wrote: I've been told that the application AIRMAIL does notinterface the Elecraft to control frequency and transmission. A recent version of AIRMAIL, v 3.4.062, lists the K2 and K3 in the setup menu. I'd like a report of the experience of any who have tried interfacing a K3 to this version of AIRMAIL and using the rig control function. 73 de Red, WOXW __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecrafthttp://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htmhttp://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- *Gary - VK1ZZ Skype: Gary.VK1ZZ http://www.qsl.net/vk1zz Motorhome Portable The Shack* *Elecraft K3 P3 Panadapter KPA500FT KAT500FT** * __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] OT - anyone have experience with effects of metalroofs on antenna performace?
This note is for the log/web manager. I note that each time somebody comments on a thread ( the recent ones on metal roof), a new email is sent to all recipients. This is a nuisance cluttering the inbox. My experience with blogs is all comments are retained on the server Under one heading, and an email is sent daily to anybody interested in that subject upon request. Hope something could be done about that. Paul Chebi Kk4ptv Sent from my iPhone On Jul 5, 2013, at 6:46 PM, Phil Shepard ph...@riousa.com wrote: Ah, memories … I took an antenna class from Balanis, and we used photo copies of his fledgling book, acting as proofers. He was my senior EE project advisor as well. Quite a character. I wish I still remembered a fraction of what I knew then. Hi hi. Phil, NS7P On Jul 5, 2013, at 3:11 PM, kevinr kev...@coho.net wrote: I was just reviewing my copy of Balanis and remembered the grueling effort of the class. I took it in grad school with a crazy Greek professor who worked with Balanis. He wound up being my thesis advisor :) Kevin. KD5ONS On 7/5/2013 1:54 PM, george fritkin wrote: I remember the toughest class was antenna theory. As an undergrad EE student, I believed that this class would kill my plan to be an EE. I got a 25 (out of 100)! No bragging, it was the highest grade. They graded on a curve. My prof was a world renown antenna expert. He liked to @#* with us. So if anyone figures out this antenna stuff email me __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html