Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Yes, I've had the same problem, after I tune , I get low power out indicated Gordan, e72x, I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547895p2561561.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Hi, I also have this problem that SSB power is low following the use of TUNE. I don't have the built in tuner. I use the tune (hold) function to generate 10W CW for my external remote auto-tuner. In the contest I got into the habit of doing a power cycle after tuning (I now see that there are better ways which helps. I have also observed the slow creeping up of power over several transmissions until it eventually recovers fully. I don't have any precision instrumentation to measure peak power. I just observe the average power on my analog SWR meter and I estimate I start out at 2/3 of what is should be after using tune. I join others in hoping for a quick resolution to this. There are two menu entrys that effect power in addition to the front panel PWR control. There may be interaction between these in certain combinations of settings or BAND and MODE. Wayne has limited internet access this weekend and has asked me to request information from those who are experiencing this problem. Please send your settings for the following. snip - AB2TC - Knut -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547895p2558473.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] K3 3.04 Power Output After Tune
During the WPX SSB contest I have noticed the same low output that others have noticed after ATU TUNE. I just wanted to add one comment. After low output is remedied with TUNE, the firmware seems to remember that fact. That is, when I return to that vicinity after SP QSOs elsewhere (ATU flashes), the output seems OK. TUNE doesn't seem necessary unless ATU TUNE has just been used to reduce SWR. 73, Paul W8TM __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Llye, FWIW, I am experiencing the same issue running QRP with the KAT3, when it is in use, in 3.03 It does not seem to happen when the KAT3 is bypassed. Engaging the main TUNE button (not the KAT tune), seems to put it back to normal. Now if I can figure out why my two sounds like zero *sigh* 73, Julius Thank you for the observations on SSB Power Control before and after KAT3 tuning or when in bypass. We'll be looking more closely at this next week. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html - Julius Fazekas N2WN Tennessee Contest Group http://www.k4ro.net/tcg/index.html Tennessee QSO Party http://www.tnqp.org/ Elecraft K2/100 #4455 Elecraft K3/100 #366 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547895p2553180.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
There are two menu entrys that effect power in addition to the front panel PWR control. There may be interaction between these in certain combinations of settings or BAND and MODE. Wayne has limited internet access this weekend and has asked me to request information from those who are experiencing this problem. Please send your settings for the following. Config TUN PWR Config PWR SET Band and Mode and front panel PWR control. Please send this information to n...@elecraft.com Thanks, 73, Bob N6CM On Sun, Mar 29, 2009 at 9:48 AM, Julius Fazekas n2wn phriend...@yahoo.com wrote: Llye, FWIW, I am experiencing the same issue running QRP with the KAT3, when it is in use, in 3.03 It does not seem to happen when the KAT3 is bypassed. Engaging the main TUNE button (not the KAT tune), seems to put it back to normal. Now if I can figure out why my two sounds like zero *sigh* 73, Julius Thank you for the observations on SSB Power Control before and after KAT3 tuning or when in bypass. We'll be looking more closely at this next week. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html - Julius Fazekas N2WN Tennessee Contest Group http://www.k4ro.net/tcg/index.html Tennessee QSO Party http://www.tnqp.org/ Elecraft K2/100 #4455 Elecraft K3/100 #366 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547895p2553180.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] K3 3.04 Power Output After Tune
Here ya go Wayne. Config TUN PWR nor Config PWR SET per band Band and Mode all bands phone usb and lsb and front panel PWR control. 120w I can't seem to change to cw mode and have it correct the low power out after tune. I have cw wght set to ssb+cw btw. I actually turn the power control cw (up) even though it is maxed on the lcd, and after several turns all is ok until the next tune. I tried different setting on tun pwr and pwr set with no change. I have cleared tuner mem settings with no help. This k3 seems to have lower output than my other k3. s/n 2737 vs s/n1194. It's about 20w less on phone. I've seen this since k3fw3r03 btw. k3fw2r82 and before has normal power out after a tune, although still quite a bit lower than the s/n 1194. 100w on s/n1194 shows 100w on my peak reading meter. 2737 around 70w depending on band. I'm sticking with 2r82 for now. Randy K8RDD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I've been running v3.04 during the CQ WPX contest (7 hours of heavy use so far) and have had no problems with it at all. 73, Dave AB7E Augie Hansen wrote: Jim - W6VAR wrote: I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Yes, I've had the same problem, especially when operating split on 40 meters. Gus Hansen KB0YH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I assume by after I tune you mean pressing the XMIT/TUNE button to create a CW carrier at some level between 20 Watts and 100 Watts. I've tried various combinations of power and both the actual measured output and the indicated output on the K3 are both fine. No problem here at all. 73 Dave, G4AON K3/100 #80, f/w 3.04 I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] K3 3.04 Power Output After Tune
I DG6HD have this problem since more ser 3.03 I go on 80m without tunen it go with 120w raus swr 1:1,1 I tune and he goes only for each to volume with 30-80w raus then must I him highly whistle or briefly xmit press and the k3 fully drive out then has he the full achievement up to the next to tunen or tape changes on usb are the achievements somewhat is not so bad the error more highly there mine by Elecraft together built number 2193 has 100w ATU filter 6-2,8-2,1-0,4 2.Empfänger filter 2,8-2,1 What is the error? DG6HD Dennis -- Pt! Schon vom neuen GMX MultiMessenger gehört? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger01 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Dave G4AON wrote: I assume by after I tune you mean pressing the XMIT/TUNE button to create a CW carrier at some level between 20 Watts and 100 Watts. I've tried various combinations of power and both the actual measured output and the indicated output on the K3 are both fine. No problem here at all. My K3 has a KAT3 installed. When operating split on 40 meters it is necessary to tune one of my TX antennas. Following the successful tune operation (1:1 match) an attempt to call results in very low (2 watts) output power. Neither talking nor whistling causes the power to return to 100 watts. I have to swap VFOs, switch to CW and key the rig to get the power back to the requested value. Then, of course, return to LSB mode, swap VFOs back so that I'm transmitting on the correct frequency. Based on Jim's description I believe he is having the same problem. Gus Hansen KB0YH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 S/N 1749 with 3.04. There is definitely something strange with the power output. I turned off the radio last night, powered up this morning, retuned (used tune) the amp for 20 mtrs and was seeing 600w out. After several contest contacts I noticed the atu was still in line and switched it out. Next SSB transmission showed power was about 90 watts from the amplifier. Turned K3 power up from 20 watts drive to 30 and amplifier output was about 300 watts. Amp is ACOM 1000. Mike - N5WNG -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547892p2549045.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Sorry guys, you are correct. There is a problem with the ATU function on SSB in ver 3.04. After tuning with the ATU in circuit, the power is much lower on SSB until the TUNE button outputs a full carrier. The ATU isn't normally used here these days as my antennas are resonant. 73 Dave, G4AON K3/100 #80, f/w 3.04 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Augie Hansen wrote: Dave G4AON wrote: I assume by after I tune you mean pressing the XMIT/TUNE button to create a CW carrier at some level between 20 Watts and 100 Watts. I've tried various combinations of power and both the actual measured output and the indicated output on the K3 are both fine. No problem here at all. My K3 has a KAT3 installed. When operating split on 40 meters it is necessary to tune one of my TX antennas. Following the successful tune operation (1:1 match) an attempt to call results in very low (2 watts) output power. Neither talking nor whistling causes the power to return to 100 watts. I have to swap VFOs, switch to CW and key the rig to get the power back to the requested value. Then, of course, return to LSB mode, swap VFOs back so that I'm transmitting on the correct frequency. Based on Jim's description I believe he is having the same problem. Gus Hansen KB0YH I see a power cutback after KAT3 tune also - not as dramatic as Gus describes.Not using SPLIT. Using the 2TONE test signal on SSB yields ~100W, tune the KAT3 and 2TONE test again yields ~65W. Change to CW, tap the key, back to SSB and I get ~100W. All this into a dummy load on any band. Other observations: If you tune the KAT3 then bypass the KAT3 it still only outputs ~65W. I also tried various settings of TUN PWR (10, 2, NOR), all acted the same. Works OK on FW2.82, 'fails' on FW3.03 and FW3.04 73, Bill N2BC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Thank you for the observations on SSB Power Control before and after KAT3 tuning or when in bypass. We'll be looking more closely at this next week. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Same problem here Bill Low power output (40watts - 60watts) after using the tuner. CW produces full output. 73, Nick ve3ey On 3/28/2009 10:03 AM, Bill Coleman wrote: Augie Hansen wrote: Dave G4AON wrote: I assume by after I tune you mean pressing the XMIT/TUNE button to create a CW carrier at some level between 20 Watts and 100 Watts. I've tried various combinations of power and both the actual measured output and the indicated output on the K3 are both fine. No problem here at all. My K3 has a KAT3 installed. When operating split on 40 meters it is necessary to tune one of my TX antennas. Following the successful tune operation (1:1 match) an attempt to call results in very low (2 watts) output power. Neither talking nor whistling causes the power to return to 100 watts. I have to swap VFOs, switch to CW and key the rig to get the power back to the requested value. Then, of course, return to LSB mode, swap VFOs back so that I'm transmitting on the correct frequency. Based on Jim's description I believe he is having the same problem. Gus Hansen KB0YH I see a power cutback after KAT3 tune also - not as dramatic as Gus describes.Not using SPLIT. Using the 2TONE test signal on SSB yields ~100W, tune the KAT3 and 2TONE test again yields ~65W. Change to CW, tap the key, back to SSB and I get ~100W. All this into a dummy load on any band. Other observations: If you tune the KAT3 then bypass the KAT3 it still only outputs ~65W. I also tried various settings of TUN PWR (10, 2, NOR), all acted the same. Works OK on FW2.82, 'fails' on FW3.03 and FW3.04 73, Bill N2BC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I'm having a problem of low power output on SSB on 40 meters. Call for 100 watts, get 50 or less peak on LP-100 watt meter. Reinstalled FW 3.04, calibrated K3 watt meter, calibrated TX GAIN using the K3 utility and an OHR 100 watt dummy load. Problem remains. CW output is OK on all bands, albeit a bit on the low side (around 90 out when 100 requested). John, W2GW K3 384 -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net]on Behalf Of Jim - W6VAR Sent: Friday, March 27, 2009 11:34 PM To: elecraft@mailman.qth.net Subject: [Elecraft] [K3] K3 3.04 Power Output After Tune I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547892p2547892.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I can turn up the power control and it will increase to where it should be, even though the power control is allready set to 120w. After a turn or two the power goes back to approx. 100w. I can tap tune again and it will drop to approx 30 w peak on ssb. Talk and turn the power adjust up, even though it says 120w brings the power back up. It's then OK until I tap tune again! Randy K8RDD - Original Message - From: Nick Lekic ve...@rogers.com To: Bill Coleman n...@stny.rr.com Cc: K3support k3supp...@elecraft.com; elecraft@mailman.qth.net Sent: Saturday, March 28, 2009 10:19 AM Subject: Re: [Elecraft] [K3] K3 3.04 Power Output After Tune Same problem here Bill Low power output (40watts - 60watts) after using the tuner. CW produces full output. 73, Nick ve3ey On 3/28/2009 10:03 AM, Bill Coleman wrote: Augie Hansen wrote: Dave G4AON wrote: I assume by after I tune you mean pressing the XMIT/TUNE button to create a CW carrier at some level between 20 Watts and 100 Watts. I've tried various combinations of power and both the actual measured output and the indicated output on the K3 are both fine. No problem here at all. My K3 has a KAT3 installed. When operating split on 40 meters it is necessary to tune one of my TX antennas. Following the successful tune operation (1:1 match) an attempt to call results in very low (2 watts) output power. Neither talking nor whistling causes the power to return to 100 watts. I have to swap VFOs, switch to CW and key the rig to get the power back to the requested value. Then, of course, return to LSB mode, swap VFOs back so that I'm transmitting on the correct frequency. Based on Jim's description I believe he is having the same problem. Gus Hansen KB0YH I see a power cutback after KAT3 tune also - not as dramatic as Gus describes.Not using SPLIT. Using the 2TONE test signal on SSB yields ~100W, tune the KAT3 and 2TONE test again yields ~65W. Change to CW, tap the key, back to SSB and I get ~100W. All this into a dummy load on any band. Other observations: If you tune the KAT3 then bypass the KAT3 it still only outputs ~65W. I also tried various settings of TUN PWR (10, 2, NOR), all acted the same. Works OK on FW2.82, 'fails' on FW3.03 and FW3.04 73, Bill N2BC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Same here. Augie Hansen escribió: Jim - W6VAR wrote: I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Yes, I've had the same problem, especially when operating split on 40 meters. Gus Hansen KB0YH -- Rubén Navarro Huedo - EA5BZ http://www.palotes.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I also experienced the low power issue. It has improved significantly since I cleared the ATU memory using the clear function. Too soon to know if that actually cured the problem. George AI4VZ - Original Message - From: John E. Reiser reis...@optonline.net To: Jim - W6VAR w6...@comcast.net; elecraft@mailman.qth.net Sent: Saturday, March 28, 2009 11:22 AM Subject: Re: [Elecraft] [K3] K3 3.04 Power Output After Tune I'm having a problem of low power output on SSB on 40 meters. Call for 100 watts, get 50 or less peak on LP-100 watt meter. Reinstalled FW 3.04, calibrated K3 watt meter, calibrated TX GAIN using the K3 utility and an OHR 100 watt dummy load. Problem remains. CW output is OK on all bands, albeit a bit on the low side (around 90 out when 100 requested). John, W2GW K3 384 -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net]on Behalf Of Jim - W6VAR Sent: Friday, March 27, 2009 11:34 PM To: elecraft@mailman.qth.net Subject: [Elecraft] [K3] K3 3.04 Power Output After Tune I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547892p2547892.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
I've switched back to fw2r80. It seems for me to be the most stable on tx ssb. fw3r04 is very squirrelly on ssb. Randy K8RDD - Original Message - From: Ruben Navarro Huedo runa...@gmail.com To: Augie Hansen augie.han...@comcast.net; Elecraft_List elecraft@mailman.qth.net Sent: Saturday, March 28, 2009 3:50 PM Subject: Re: [Elecraft] [K3] K3 3.04 Power Output After Tune Same here. Augie Hansen escribió: Jim - W6VAR wrote: I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Yes, I've had the same problem, especially when operating split on 40 meters. Gus Hansen KB0YH -- Rubén Navarro Huedo - EA5BZ http://www.palotes.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] K3 3.04 Power Output After Tune
I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547892p2547892.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] K3 3.04 Power Output After Tune
I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Jim W6VAR K3 1644 -- View this message in context: http://n2.nabble.com/K3-3.04-Power-Output-After-Tune-tp2547895p2547895.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 3.04 Power Output After Tune
Jim - W6VAR wrote: I updated the firmware to 3.04 last night. Today, after I tune, I get no or low power out indicated on the RF meter in SSB. Keying down momentarily restores power in SSB. Are others experiencing this? Yes, I've had the same problem, especially when operating split on 40 meters. Gus Hansen KB0YH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
