Re: [Elecraft] Spam bounce?
It seems that the general settings of spam filtering is the culprit. Some ISP blocking mass freemail providers (yahoo.com, aol.com etc.). An email address change is the solution. 73 Martin OK1RR F5UL napsal(a): May be out of order on this reflector, but yesterday I had a mssage to post concerning a big trouble with my K2 SN 4498 and the following was all what I got in return...!!! So what can I do to post an e-mail from Europe? Thank you very much for the pass band ! F5UL -- Reporting-MTA: dns; wanadoo.fr X-SMTP-Server-Queue-ID: 8B4D31C00152 X-SMTP-Server-Sender: rfc822; [EMAIL PROTECTED] Arrival-Date: Fri, 8 Apr 2005 22:47:17 +0200 (CEST) Final-Recipient: rfc822; elecraft@mailman.qth.net Action: failed Status: 5.0.0 Diagnostic-Code: X-SMTP-Server; host - Hello the list, Up to this morning, this K2 was a nice and good worker, with during the last six month about a thousand QSO under his belt ! But this morning turning it on, I just got a vigorous howl ( very low freq nois !). I turn it off, and on after a few second. The Rx start normaly and the noise start again after a few second. Re-turn off and tunr on and no howl and Rx is working correctly! The set was in CW mode so I turn down power (to abt 2/3 watts) and close the key... The result is correct on 1.8, 3.5, 7.0 but nil on the rest of the bands. Closing the key a little longer on 7.0 the rig goes to curent overange in abt 10/12 second and power fall down to zero. So power off, open the rig, remove the bottom cover and before removing the heat sink just check the resistance of driver and PAOn Q6 (driver) E to Gnd 1.3 ohm, B to Gnd 76/80 ohms, and C to Gnd 500 ohms. On Pa C to Gnd 600 ohms, B to Gnd 120/130 ohm E to Gnd 0 (it's normal!)They seems to be normals but any time I close the key I get High Cur and power out ZERO !! I do n,ot know what to do so I will wait till tomorow and hope to get some indications from the list ! Thanks in advance guy, BCNU 72 Bob/F5UL ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Spam bounce?
In a message dated 09/04/05 09:10:45 GMT Daylight Time, [EMAIL PROTECTED] writes: But this morning turning it on, I just got a vigorous howl ( very low freq nois !). I turn it off, and on after a few second. The Rx start normaly and the noise start again after a few second. Re-turn off and tunr on and no howl and Rx is working correctly! - With the RX problem a good point to start with would be to check the PSU as the symptoms can sometimes be caused by a very low supply voltage. A common problem with battery powered equipment is to have LF instability when the batteries were dying. The same can apply with a defective PSU. To Martin, OK1RR, I can assure you that AOL are not a freemail provider, far from it as they charge more than many others for the service. Bob, G3VVT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Spam bounce?
AFIK, and certainly in UK, the Wanadoo ISP is far from Freemail. I'm on Freeserve which is the UK Name for Wanadoo and I have never experienced a bounce because of my ISP's policies. I can't offer any good reasons why they are bouncing though sO I suppose I had better stop using bandwidth. 73 Mike G8NXD -- On 9 Apr 2005 at 10:09, Martin Kratoska wrote: It seems that the general settings of spam filtering is the culprit. Some ISP blocking mass freemail providers (yahoo.com, aol.com etc.). An email address change is the solution. 73 Martin OK1RR F5UL napsal(a): May be out of order on this reflector, but yesterday I had a mssage to post concerning a big trouble with my K2 SN 4498 and the following was all what I got in return...!!! So what can I do to post an e-mail from Europe? Thank you very much for the pass band ! F5UL -- Reporting-MTA: dns; wanadoo.fr X-SMTP-Server-Queue-ID: 8B4D31C00152 X-SMTP-Server-Sender: rfc822; [EMAIL PROTECTED] Arrival-Date: Fri, 8 Apr 2005 22:47:17 +0200 (CEST) Final-Recipient: rfc822; elecraft@mailman.qth.net Action: failed Status: 5.0.0 Diagnostic-Code: X-SMTP-Server; host - Hello the list, Up to this morning, this K2 was a nice and good worker, with during the last six month about a thousand QSO under his belt ! But this morning turning it on, I just got a vigorous howl ( very low freq nois !). I turn it off, and on after a few second. The Rx start normaly and the noise start again after a few second. Re-turn off and tunr on and no howl and Rx is working correctly! The set was in CW mode so I turn down power (to abt 2/3 watts) and close the key... The result is correct on 1.8, 3.5, 7.0 but nil on the rest of the bands. Closing the key a little longer on 7.0 the rig goes to curent overange in abt 10/12 second and power fall down to zero. So power off, open the rig, remove the bottom cover and before removing the heat sink just check the resistance of driver and PAOn Q6 (driver) E to Gnd 1.3 ohm, B to Gnd 76/80 ohms, and C to Gnd 500 ohms. On Pa C to Gnd 600 ohms, B to Gnd 120/130 ohm E to Gnd 0 (it's normal!)They seems to be normals but any time I close the key I get High Cur and power out ZERO !! I do n,ot know what to do so I will wait till tomorow and hope to get some indications from the list ! Thanks in advance guy, BCNU 72 Bob/F5UL ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Spam bounce?
You cannot be serious. To suggest someone changes his email address and ISP to solve the problem with the spam filtering of this reflector is a severe case of the tail wagging the dog, in my opinion. Julian, G4ILO Martin Kratoska [EMAIL PROTECTED] wrote: It seems that the general settings of spam filtering is the culprit. Some ISP blocking mass freemail providers (yahoo.com, aol.com etc.). An email address change is the solution. 73 Martin OK1RR ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Spam bounce?
May be out of order on this reflector, but yesterday I had a mssage to post concerning a big trouble with my K2 SN 4498 and the following was all what I got in return...!!! So what can I do to post an e-mail from Europe? Thank you very much for the pass band ! F5UL -- Reporting-MTA: dns; wanadoo.fr X-SMTP-Server-Queue-ID: 8B4D31C00152 X-SMTP-Server-Sender: rfc822; [EMAIL PROTECTED] Arrival-Date: Fri, 8 Apr 2005 22:47:17 +0200 (CEST) Final-Recipient: rfc822; elecraft@mailman.qth.net Action: failed Status: 5.0.0 Diagnostic-Code: X-SMTP-Server; host - Hello the list, Up to this morning, this K2 was a nice and good worker, with during the last six month about a thousand QSO under his belt ! But this morning turning it on, I just got a vigorous howl ( very low freq nois !). I turn it off, and on after a few second. The Rx start normaly and the noise start again after a few second. Re-turn off and tunr on and no howl and Rx is working correctly! The set was in CW mode so I turn down power (to abt 2/3 watts) and close the key... The result is correct on 1.8, 3.5, 7.0 but nil on the rest of the bands. Closing the key a little longer on 7.0 the rig goes to curent overange in abt 10/12 second and power fall down to zero. So power off, open the rig, remove the bottom cover and before removing the heat sink just check the resistance of driver and PAOn Q6 (driver) E to Gnd 1.3 ohm, B to Gnd 76/80 ohms, and C to Gnd 500 ohms. On Pa C to Gnd 600 ohms, B to Gnd 120/130 ohm E to Gnd 0 (it's normal!)They seems to be normals but any time I close the key I get High Cur and power out ZERO !! I do n,ot know what to do so I will wait till tomorow and hope to get some indications from the list ! Thanks in advance guy, BCNU 72 Bob/F5UL ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
