subject:"\[Emc\-users\] Error on loading 5i25\/7i76"

Re: [Emc-users] Error on loading 5i25/7i76

2020-10-11 Thread Alan Condit

Thanks all,

It wasn’t anything other than a senior brain fart. I had the parallel cable 
plugged into the pc’s parallel port instead of the 5i25. After I checked out 
the cable from the outside of the box to the 7i76 and found nothing wrong, I 
woke up in the middle of the night and realized what I had done wrong. Duh!!!

> From: andy pugh 
> Subject: Re: [Emc-users] Error on loading 5i25/7i76
> Date: October 9, 2020 at 5:02:32 PM CDT
> To: "Enhanced Machine Controller (EMC)" 
> 
> 
> On Fri, 9 Oct 2020 at 20:12, Alan Condit  wrote:
> 
>> I am trying to configure my 5i25/7i76 for my CNC Lathe.  I had a working 
>> configuration for 2.7.x but I may have lost it in our move from Oregon to 
>> Iowa. I took what I thought was the working configuration, I probably made a 
>> mistake. I upgraded to 2.8 without verifying the configuration.
>> 
>> I ran pcnconf on the configuration and now I am getting the following error 
>> when I try to start it up.
> 
> If you still have the old config files then they should still work.
> (LinuxCNC will make the required modifications to the INI and HAL
> automatically[1])
> 
> 
> [1] Has anyone heard any stories of that script not working? I was
> expecting a rash of failures and error reports.
> 
> -- 
> atp
> "A motorcycle is a bicycle with a pandemonium attachment and is
> designed for the especial use of mechanical geniuses, daredevils and
> lunatics."
> — George Fitch, Atlanta Constitution Newspaper, 1912


Alan


___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Error on loading 5i25/7i76

2020-10-09 Thread Gene Heskett

On Friday 09 October 2020 17:42:47 Alan Condit wrote:

> Here is a link to my hal file  
your sseral port address is different from mine on a 6040 mill:
loadrt hm2_pci config="num_pwmgens=1 num_stepgens=4 num_encoders=1 
sserial_port_0=1xxx"
but my G0704, useing the same card combo does not have the last option. 
Works fine.
But I've no clue to what it might mean.

> and my 
> ini file .

And I have this clear at the bottom of my .ini file, but only on one of 
the two machines using that interface combo.

#*
[HOSTMOT2]
#  This is for info only 
DRIVER=hm2_pci
BOARD=5i25

Good luck Alan. But check that cable.
> ___
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users


Cheers, Gene Heskett
-- 
"There are four boxes to be used in defense of liberty:
 soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
If we desire respect for the law, we must first make the law respectable.
 - Louis D. Brandeis
Genes Web page 


___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Error on loading 5i25/7i76

2020-10-09 Thread andy pugh

On Fri, 9 Oct 2020 at 20:12, Alan Condit  wrote:

> I am trying to configure my 5i25/7i76 for my CNC Lathe.  I had a working 
> configuration for 2.7.x but I may have lost it in our move from Oregon to 
> Iowa. I took what I thought was the working configuration, I probably made a 
> mistake. I upgraded to 2.8 without verifying the configuration.
>
> I ran pcnconf on the configuration and now I am getting the following error 
> when I try to start it up.

If you still have the old config files then they should still work.
(LinuxCNC will make the required modifications to the INI and HAL
automatically[1])


[1] Has anyone heard any stories of that script not working? I was
expecting a rash of failures and error reports.

-- 
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the especial use of mechanical geniuses, daredevils and
lunatics."
— George Fitch, Atlanta Constitution Newspaper, 1912


___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Error on loading 5i25/7i76

2020-10-09 Thread Peter C. Wallace

On Fri, 9 Oct 2020, Alan Condit wrote:

Date: Fri, 9 Oct 2020 16:42:47 -0500
From: Alan Condit 
Reply-To: "Enhanced Machine Controller (EMC)"

To: "Emc-users@lists.sourceforge.net" 
Subject: Re: [Emc-users] Error on loading 5i25/7i76

Here is a link to my hal file <https://pastebin.com/aXyt6UFd> and my ini file 
<https://pastebin.com/snWeAuMu>.
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Not finding the 7I76 could be a cable issue or missing 5V or field power at the 
7I76. It can also be due to mis-set cable power jumpers on the 7I76 and 5I25

Peter Wallace
Mesa Electronics

___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Error on loading 5i25/7i76

2020-10-09 Thread Alan Condit

Here is a link to my hal file  and my ini file 
.
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Error on loading 5i25/7i76

2020-10-09 Thread Gene Heskett

On Friday 09 October 2020 15:09:26 Alan Condit wrote:

> I am trying to configure my 5i25/7i76 for my CNC Lathe.  I had a
> working configuration for 2.7.x but I may have lost it in our move
> from Oregon to Iowa. I took what I thought was the working
> configuration, I probably made a mistake. I upgraded to 2.8 without
> verifying the configuration.
>
> I ran pcnconf on the configuration and now I am getting the following
> error when I try to start it up.
>
> Debug file information:
> Note: Using POSIX realtime
> ./my_LinuxCNC_lathe.hal:38: Pin 'hm2_5i25.0.7i76.0.0.output-00' does
> not exist
>
> Print file information:
> RUN_IN_PLACE=no
> LINUXCNC_DIR=
> LINUXCNC_BIN_DIR=/usr/bin
> LINUXCNC_TCL_DIR=/usr/lib/tcltk/linuxcnc
> LINUXCNC_SCRIPT_DIR=
> LINUXCNC_RTLIB_DIR=/usr/lib/linuxcnc/modules
> LINUXCNC_CONFIG_DIR=
> LINUXCNC_LANG_DIR=/usr/lib/tcltk/linuxcnc/msgs
> INIVAR=inivar
> HALCMD=halcmd
> LINUXCNC_EMCSH=/usr/bin/wish8.6
> LINUXCNC - 2.8.0
> Machine configuration directory is
> '/home/acondit/linuxcnc/configs/myCNCLathe' Machine configuration file
> is 'myCNCLathe.ini'
> INIFILE=/home/acondit/linuxcnc/configs/myCNCLathe/myCNCLathe.ini
> VERSION=1.1
> PARAMETER_FILE=linuxcnc.var
> TASK=milltask
> HALUI=halui
> DISPLAY=axis
> COORDINATES=XZ
> KINEMATICS=trivkins coordinates=XZ
> Starting LinuxCNC...
> Starting LinuxCNC server program: linuxcncsvr
> Loading Real Time OS, RTAPI, and HAL_LIB modules
> Starting LinuxCNC IO program: io
> Starting HAL User Interface program: halui
> Found file(REL): ./myCNCLathe.hal
> Shutting down and cleaning up LinuxCNC...
> Running HAL shutdown script
> hm2: loading Mesa HostMot2 driver version 0.15
> hm2_pci: loading Mesa AnyIO HostMot2 driver version 0.7
> hm2_pci: discovered 5i25 at :03:02.0
> hm2/hm2_5i25.0: Smart Serial Firmware Version 43
> hm2/hm2_5i25.0: 34 I/O Pins used:
> hm2/hm2_5i25.0: IO Pin 000 (P3-01): StepGen #0, pin Direction
> (Output) hm2/hm2_5i25.0: IO Pin 001 (P3-14): StepGen #0, pin Step
> (Output) hm2/hm2_5i25.0: IO Pin 002 (P3-02): StepGen #1, pin
> Direction (Output) hm2/hm2_5i25.0: IO Pin 003 (P3-15): StepGen #1,
> pin Step (Output) hm2/hm2_5i25.0: IO Pin 004 (P3-03): StepGen #2,
> pin Direction (Output) hm2/hm2_5i25.0: IO Pin 005 (P3-16): StepGen
> #2, pin Step (Output) hm2/hm2_5i25.0: IO Pin 006 (P3-04): IOPort
> hm2/hm2_5i25.0: IO Pin 007 (P3-17): IOPort
> hm2/hm2_5i25.0: IO Pin 008 (P3-05): IOPort
> hm2/hm2_5i25.0: IO Pin 009 (P3-06): IOPort
> hm2/hm2_5i25.0: IO Pin 010 (P3-07): IOPort
> hm2/hm2_5i25.0: IO Pin 011 (P3-08): IOPort
> hm2/hm2_5i25.0: IO Pin 012 (P3-09): IOPort
> hm2/hm2_5i25.0: IO Pin 013 (P3-10): IOPort
> hm2/hm2_5i25.0: IO Pin 014 (P3-11): Encoder #0, pin Index (Input)
> hm2/hm2_5i25.0: IO Pin 015 (P3-12): Encoder #0, pin B (Input)
> hm2/hm2_5i25.0: IO Pin 016 (P3-13): Encoder #0, pin A (Input)
> hm2/hm2_5i25.0: IO Pin 017 (P2-01): IOPort
> hm2/hm2_5i25.0: IO Pin 018 (P2-14): IOPort
> hm2/hm2_5i25.0: IO Pin 019 (P2-02): IOPort
> hm2/hm2_5i25.0: IO Pin 020 (P2-15): IOPort
> hm2/hm2_5i25.0: IO Pin 021 (P2-03): IOPort
> hm2/hm2_5i25.0: IO Pin 022 (P2-16): IOPort
> hm2/hm2_5i25.0: IO Pin 023 (P2-04): IOPort
> hm2/hm2_5i25.0: IO Pin 024 (P2-17): IOPort
> hm2/hm2_5i25.0: IO Pin 025 (P2-05): IOPort
> hm2/hm2_5i25.0: IO Pin 026 (P2-06): IOPort
> hm2/hm2_5i25.0: IO Pin 027 (P2-07): IOPort
> hm2/hm2_5i25.0: IO Pin 028 (P2-08): IOPort
> hm2/hm2_5i25.0: IO Pin 029 (P2-09): IOPort
> hm2/hm2_5i25.0: IO Pin 030 (P2-10): IOPort
> hm2/hm2_5i25.0: IO Pin 031 (P2-11): IOPort
> hm2/hm2_5i25.0: IO Pin 032 (P2-12): IOPort
> hm2/hm2_5i25.0: IO Pin 033 (P2-13): IOPort
> hm2/hm2_5i25.0: registered
> hm2_5i25.0: initialized AnyIO board at :03:02.0
> hm2_5i25.0: dropping AnyIO board at :03:02.0
> hm2/hm2_5i25.0: unregistered
> hm2_pci: driver unloaded
> hm2: unloading
> Removing HAL_LIB, RTAPI, and Real Time OS modules
> Removing NML shared memory segments
>
> Debug file information:
> Note: Using POSIX realtime
> ./myCNCLathe.hal:38: Pin 'hm2_5i25.0.7i76.0.0.output-00' does not
> exist 3109
> Stopping realtime threads
> Unloading hal components
> RTAPI_PCI: Unmapped 65536 bytes at 0x7f75bc6b4000
> Note: Using POSIX realtime
>
> I tried to attach my pncconf file but it was too large.
> Thanks,
> Alan
>
After a 2k mile move, and its not finding the 7i76 which it has to do 
thru the sserial port on the 5i25, I'd suspect you put it back together 
with a duff cable. Stick both ends of it back in the vice and give it a 
squeeze if its the usual IDC connectors, and padding the open end of the 
tin shell with a piece of softer flat wood. If that doesn't work, I'd 
undertaken to 'ring' it, wire by wire with an ohmmeter. If its iffy, 
make a new cable. I keep a roll of 26 wire ribbon cable, stripping one 
wire off it to make it 25, and connectors "on the shelf" just in case.  
This is a case where gold flashed

[Emc-users] Error on loading 5i25/7i76

2020-10-09 Thread Alan Condit

I am trying to configure my 5i25/7i76 for my CNC Lathe.  I had a working 
configuration for 2.7.x but I may have lost it in our move from Oregon to Iowa. 
I took what I thought was the working configuration, I probably made a mistake. 
I upgraded to 2.8 without verifying the configuration.

I ran pcnconf on the configuration and now I am getting the following error 
when I try to start it up.

Debug file information:
Note: Using POSIX realtime
./my_LinuxCNC_lathe.hal:38: Pin 'hm2_5i25.0.7i76.0.0.output-00' does not exist

Print file information:
RUN_IN_PLACE=no
LINUXCNC_DIR=
LINUXCNC_BIN_DIR=/usr/bin
LINUXCNC_TCL_DIR=/usr/lib/tcltk/linuxcnc
LINUXCNC_SCRIPT_DIR=
LINUXCNC_RTLIB_DIR=/usr/lib/linuxcnc/modules
LINUXCNC_CONFIG_DIR=
LINUXCNC_LANG_DIR=/usr/lib/tcltk/linuxcnc/msgs
INIVAR=inivar
HALCMD=halcmd
LINUXCNC_EMCSH=/usr/bin/wish8.6
LINUXCNC - 2.8.0
Machine configuration directory is '/home/acondit/linuxcnc/configs/myCNCLathe'
Machine configuration file is 'myCNCLathe.ini'
INIFILE=/home/acondit/linuxcnc/configs/myCNCLathe/myCNCLathe.ini
VERSION=1.1
PARAMETER_FILE=linuxcnc.var
TASK=milltask
HALUI=halui
DISPLAY=axis
COORDINATES=XZ
KINEMATICS=trivkins coordinates=XZ
Starting LinuxCNC...
Starting LinuxCNC server program: linuxcncsvr
Loading Real Time OS, RTAPI, and HAL_LIB modules
Starting LinuxCNC IO program: io
Starting HAL User Interface program: halui
Found file(REL): ./myCNCLathe.hal
Shutting down and cleaning up LinuxCNC...
Running HAL shutdown script
hm2: loading Mesa HostMot2 driver version 0.15
hm2_pci: loading Mesa AnyIO HostMot2 driver version 0.7
hm2_pci: discovered 5i25 at :03:02.0
hm2/hm2_5i25.0: Smart Serial Firmware Version 43
hm2/hm2_5i25.0: 34 I/O Pins used:
hm2/hm2_5i25.0: IO Pin 000 (P3-01): StepGen #0, pin Direction (Output)
hm2/hm2_5i25.0: IO Pin 001 (P3-14): StepGen #0, pin Step (Output)
hm2/hm2_5i25.0: IO Pin 002 (P3-02): StepGen #1, pin Direction (Output)
hm2/hm2_5i25.0: IO Pin 003 (P3-15): StepGen #1, pin Step (Output)
hm2/hm2_5i25.0: IO Pin 004 (P3-03): StepGen #2, pin Direction (Output)
hm2/hm2_5i25.0: IO Pin 005 (P3-16): StepGen #2, pin Step (Output)
hm2/hm2_5i25.0: IO Pin 006 (P3-04): IOPort
hm2/hm2_5i25.0: IO Pin 007 (P3-17): IOPort
hm2/hm2_5i25.0: IO Pin 008 (P3-05): IOPort
hm2/hm2_5i25.0: IO Pin 009 (P3-06): IOPort
hm2/hm2_5i25.0: IO Pin 010 (P3-07): IOPort
hm2/hm2_5i25.0: IO Pin 011 (P3-08): IOPort
hm2/hm2_5i25.0: IO Pin 012 (P3-09): IOPort
hm2/hm2_5i25.0: IO Pin 013 (P3-10): IOPort
hm2/hm2_5i25.0: IO Pin 014 (P3-11): Encoder #0, pin Index (Input)
hm2/hm2_5i25.0: IO Pin 015 (P3-12): Encoder #0, pin B (Input)
hm2/hm2_5i25.0: IO Pin 016 (P3-13): Encoder #0, pin A (Input)
hm2/hm2_5i25.0: IO Pin 017 (P2-01): IOPort
hm2/hm2_5i25.0: IO Pin 018 (P2-14): IOPort
hm2/hm2_5i25.0: IO Pin 019 (P2-02): IOPort
hm2/hm2_5i25.0: IO Pin 020 (P2-15): IOPort
hm2/hm2_5i25.0: IO Pin 021 (P2-03): IOPort
hm2/hm2_5i25.0: IO Pin 022 (P2-16): IOPort
hm2/hm2_5i25.0: IO Pin 023 (P2-04): IOPort
hm2/hm2_5i25.0: IO Pin 024 (P2-17): IOPort
hm2/hm2_5i25.0: IO Pin 025 (P2-05): IOPort
hm2/hm2_5i25.0: IO Pin 026 (P2-06): IOPort
hm2/hm2_5i25.0: IO Pin 027 (P2-07): IOPort
hm2/hm2_5i25.0: IO Pin 028 (P2-08): IOPort
hm2/hm2_5i25.0: IO Pin 029 (P2-09): IOPort
hm2/hm2_5i25.0: IO Pin 030 (P2-10): IOPort
hm2/hm2_5i25.0: IO Pin 031 (P2-11): IOPort
hm2/hm2_5i25.0: IO Pin 032 (P2-12): IOPort
hm2/hm2_5i25.0: IO Pin 033 (P2-13): IOPort
hm2/hm2_5i25.0: registered
hm2_5i25.0: initialized AnyIO board at :03:02.0
hm2_5i25.0: dropping AnyIO board at :03:02.0
hm2/hm2_5i25.0: unregistered
hm2_pci: driver unloaded
hm2: unloading
Removing HAL_LIB, RTAPI, and Real Time OS modules
Removing NML shared memory segments

Debug file information:
Note: Using POSIX realtime
./myCNCLathe.hal:38: Pin 'hm2_5i25.0.7i76.0.0.output-00' does not exist
3109
Stopping realtime threads
Unloading hal components
RTAPI_PCI: Unmapped 65536 bytes at 0x7f75bc6b4000
Note: Using POSIX realtime

I tried to attach my pncconf file but it was too large.
Thanks,
Alan



___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Error on loading 5i25/7i76

Re: [Emc-users] Error on loading 5i25/7i76

Re: [Emc-users] Error on loading 5i25/7i76

Re: [Emc-users] Error on loading 5i25/7i76

Re: [Emc-users] Error on loading 5i25/7i76

Re: [Emc-users] Error on loading 5i25/7i76

[Emc-users] Error on loading 5i25/7i76

7 matches

Site Navigation

Mail list logo

Footer information