Am 18.01.23 um 14:09 schrieb Pablo Venini:
This is the amanda.conf
org "monitoreo10_diario" # your organization name for
reports
dumpuser "amandabackup" # the user to run dumps under
mailto "xxx...@y.zz" # space separated list of operators at
your site
dumpcycle
Am 18.01.23 um 14:12 schrieb Pablo Venini:
Yes, I was also thinking about installing 3.5.1; I installed 3.5.2 from
RPM so I thought it was ok (I was reinstalling an old server wich ran
3.3.9).
I tried your suggestion and if I run amdump for each DLE, the dumps are ok
Why don't you just set
Yes, I was also thinking about installing 3.5.1; I installed 3.5.2 from
RPM so I thought it was ok (I was reinstalling an old server wich ran
3.3.9).
I tried your suggestion and if I run amdump for each DLE, the dumps are ok
El 18/1/2023 a las 06:23, Stefan G. Weichinger escribió:
Am
This is the amanda.conf
org "monitoreo10_diario" # your organization name for reports
dumpuser "amandabackup" # the user to run dumps under
mailto "xxx...@y.zz" # space separated list of operators at
your site
dumpcycle 1week # the number of days in the normal
Am 18.01.23 um 01:47 schrieb Pablo Venini:
Hi Stefan, sorry for the delay in answering. This is a backup of the
amanda server itself (configs, etc.), there is less than 100MB of
information. What worries me is that if I use a holding disk without
correcting the problem the dumps will go there
Am 18.01.23 um 01:43 schrieb Pablo Venini:
Hi Nathan, do you know if there is any setting to cause amanda to be
more verbose?
Another weird thing is that the report says:
NOTES:
planner: tapecycle (7) <= runspercycle (7)
However the config is like this:
tapecycle 8 # the number of
Hi Stefan, sorry for the delay in answering. This is a backup of the
amanda server itself (configs, etc.), there is less than 100MB of
information. What worries me is that if I use a holding disk without
correcting the problem the dumps will go there instead of going to the
vtapes.
Pablo
Hi Nathan, do you know if there is any setting to cause amanda to be
more verbose?
Another weird thing is that the report says:
NOTES:
planner: tapecycle (7) <= runspercycle (7)
However the config is like this:
tapecycle 8 # the number of tapes in rotation
runspercycle 7 # the
On Fri, Dec 30, 2022 at 11:34:14 -0300, Pablo Venini wrote:
> amcheck doesn't report errors
Hmmm.
As Stefan said, the key question is why Amanda is going into degraded
mode. Normally when I have that happen it's because the target tape
wasn't available at the start of the amdump run, but that
Hi,
On 05-01-2023 12:06, Stefan G. Weichinger wrote:
* your tapetype defines a tape with 5 GB
Would your DLEs each fit onto one vtape?
I think you should use a larger vtape ... and make sure that the full
backup of each DLE fits onto one vtape.
Please note the length of vtapes is only used
Am 30.12.22 um 15:34 schrieb Pablo Venini:
Hi Nathan,
no, (as far as I'm aware) I'm not using a holding
disk as this is a vtape backup, the dumptype is as follows:
You could fix that by defining and using a holding disk.
Then a "degraded mode backup" should work.
The
Hi Nathan,
no, (as far as I'm aware) I'm not using a holding
disk as this is a vtape backup, the dumptype is as follows:
define dumptype sm-encrypt-compress {
gui-base
comment "SM dumptype with compression and encryption"
compress client fast
encrypt client
On Thu, Dec 29, 2022 at 17:17:56 -0300, Pablo Venini wrote:
> Hi, I'm setting up a new backup server with amanda 3.5.2 on CentOS 7
> with vtapes. I've setup the vtapes directories, created the job and
> added the dlc, checked permissions, then run amcheck and it shows no
> errors. However when I
Hi, I'm setting up a new backup server with amanda 3.5.2 on CentOS 7
with vtapes. I've setup the vtapes directories, created the job and
added the dlc, checked permissions, then run amcheck and it shows no
errors. However when I run amdump, only one of the dlc gets backed up,
the other ones
14 matches
Mail list logo