] Per conto di Marc Sutter
Inviato: lunedì 18 luglio 2005 18.58
A: Asterisk Users Mailing List - Non-Commercial Discussion
Oggetto: Re: [Asterisk-Users] zaphfc: empty HDLC frame or bad CRC received
there is a list item about this issu:
http://lists.digium.com/pipermail/asterisk-users/2004-November
there is a list item about this issu:
http://lists.digium.com/pipermail/asterisk-users/2004-November/070918.html
alternatively you can try this solution on debian:
# 4)Modules configuration for startup with zaphfc AND wcfxs on
# debian stable 3.1 sarge kernel 2.4.27-2-386
# Here a
I had the same problem
could find a solution until i read to change the way the modules where loaded
(i still loaded zaphfc with modes=1 appended to it). Removing that last one did
the trick for me
Hope this may help
With kind regards
Bart Seresia
Zaakvoerder
Waasland Service
I have this problem
zaphfc: empty HDLC frame or bad CRC received
My configurations are
cat /proc/zaptel/1
Span 1: ZTHFC1 HFC-S PCI A ISDN card 0 [NT] layer 1 ACTIVATED (G3)
AMI/CCS
1 ZTHFC1/0/1 Clear
2 ZTHFC1/0/2 Clear
3 ZTHFC1/0/3 HDLCFCS
cat
Hi
all,
I'm using
asterisk 1.0.6 with bristuff-0.2.0-rc7k. I've already set up 3 boxes with
the same config, but I'm facing something strange with the fourth one
:
In my messages log,
I've got thoses lines :
kernel: zaphfc:
empty HDLC frame or bad CRC received (framelen = 4, stat =
I had a similar problem with a recent install:
* TDM11B
* 1 Port HFC Card
I got that messages about HDLC Framing errors. It ended up being the
way I loaded the required kernel modules.
1) Remove or comment install lines in /etc/modprobe.conf (or
modules.conf), regarding the kernel modules
Julian J. M.
Inviato: lunedì 27 giugno 2005 12.04
A: Asterisk Users Mailing List - Non-Commercial Discussion
Oggetto: Re: [Asterisk-Users] zaphfc: empty HDLC frame or bad CRC received
I had a similar problem with a recent install:
* TDM11B
* 1 Port HFC Card
I got that messages about HDLC
On Mon, Jun 27, 2005 at 11:04:17AM +0100, Julian J. M. wrote:
I had a similar problem with a recent install:
* TDM11B
* 1 Port HFC Card
I got that messages about HDLC Framing errors. It ended up being the
way I loaded the required kernel modules.
1) Remove or comment install lines
]
Reply-To: Asterisk Users Mailing List - Non-Commercial Discussion
asterisk-users@lists.digium.com
To: Julian J. M. [EMAIL PROTECTED],Asterisk Users Mailing List -
Non-Commercial Discussion asterisk-users@lists.digium.com
Subject: R: [Asterisk-Users] zaphfc: empty HDLC frame or bad CRC received
Date
Nick Barnes ha scritto:
I've only ever seen when the signalling is wrong. For example if the line is
in PTMP mode when it should be in PTP or vice-versa.
this is the zapata.conf:
group = 1
context=default
signalling = bri_net_ptmp
channel = 1-2
So, you're using NT mode PTMP signalling.
Hi,
Don't know if you've sorted this or not, but
zaphfc: empty HDLC frame or bad CRC received (framelen = 5,
stat = 0xff,
card = 0).
I've only ever seen when the signalling is wrong. For example if the line is
in PTMP mode when it should be in PTP or vice-versa.
this is the
Emanuele Pucciarelli wrote:
Are you sharing the IRQ? (check /proc/interrupts)
hi, what do you think? this is a bit too much low level for me.
ciop:~# cat /proc/interrupts
CPU0
0: 780877027IO-APIC-edge timer
7: 2IO-APIC-edge parport0
9: 1
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Marco Parmeggiani wrote:
hi, what do you think? this is a bit too much low level for me.
You aren't sharing it -- that's fine. I would guess that the cable is
not OK or, even more probably, the bus is not correctly terminated - but
then again, if
Hi, i've downloaded/compiled/installed the bristuffed asterisk
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a
and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine
with kernel 2.6.11. Asterisk works well if i configure the card using
isdn4linux.
I'm having problems dialing out (not
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Marco Parmeggiani wrote:
Hi, i've downloaded/compiled/installed the bristuffed asterisk
Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a
and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine
with kernel 2.6.11. Asterisk works well if i
15 matches
Mail list logo
