On 02/11/2011 07:56 AM, Albert wrote:
can anymore drop me a asterisl's config for digium te220b (with ec) or
at least some good tutorial of configuratin e1 line with that card ?
The information you are looking for (for Asterisk, not for 'asterisl')
is provided in the manual for the card; if
hi,
can anymore drop me a asterisl's config for digium te220b (with ec) or
at least some good tutorial of configuratin e1 line with that card ?
thanks in advance,
robert
--
_
-- Bandwidth and Colocation Provided by
Hi List,
It would be great if someone can share the TE220 card dahdi
configuration file.
Im using an E1 line. I know most of users find it difficult to get the
correct config file.
Im putting my efforts and will surely share my config file once it gets
working.
Thanks Regards,
Rushikesh
On Sat, Jul 31, 2010 at 09:13:46PM +0530, Rushikesh wrote:
Hi List,
It would be great if someone can share the TE220 card dahdi
configuration file.
Im using an E1 line. I know most of users find it difficult to get the
correct config file.
A. Please don't reply to an existing message
lspci can detect the card: 03:08.0 Communication controller: Digium, Inc.
Device 0220 (rev 02)
dahdi_hardware also:
astpbx ~ # dahdi_hardware
pci::03:08.0 wct4xxp+ d161:0220 Wildcard TE220 (4th Gen)
Fine. The card is indeed handled by the module (+).
astpbx ~ #
But
Maxim Litnitskiy wrote:
FALC version: 0005, Board ID: 09
The board ID switch (the rotary switch on the board) is set to 9 (nine).
If you are going to have the switches set to anything other than zero,
there must be at least one board with it set to zero, then one set to
one, then one set
Hello folks.
I've got a strange issue.
When I modprobe TE220 I do not see mesages like Launching card: 0 ..
Setting up global serial parameters.
You can see how I loaded and unloaded the card for several times -
http://asteriskpbx.ru/pastebin/11
lspci can detect the card: 03:08.0 Communication
On Mon, Jan 26, 2009 at 03:08:13PM +0300, Maxim Litnitskiy wrote:
Hello folks.
I've got a strange issue.
When I modprobe TE220 I do not see mesages like Launching card: 0 ..
Setting up global serial parameters.
You can see how I loaded and unloaded the card for several times -
Laurent a écrit :
Le 19.01.2009 08:50, Benoit a écrit :
Laurent a écrit :
Well, the telcos techs said a straight cable should do the trick, but
since i didn't get any isdn link up
with the straight, i built a crossover like what you described, with no
luck either.
Benoit a écrit :
Laurent a écrit :
Did you check (like with a multimeter or something similar) the
connectivity of your cable ? the first E1 crossover cable I made
had a problem (entirely my own fault) and I thought it didn't
work. The way I checked was by connecting the two ports of the
Laurent a écrit :
Le 19.01.2009 08:50, Benoit a écrit :
Laurent a écrit :
Well, the telcos techs said a straight cable should do the trick, but
since i didn't get any isdn link up
with the straight, i built a crossover like what you described, with no
luck either.
Hello Benoit,
Le 16.01.2009 22:29, Benoit a écrit :
And work quite well, i've duplicated this for the access thru the One400
box:
span=2,0,0,ccs,hdb3
bchan=32-46
dchan=47
With no luck until now. I'm reading the one400 manual, and here are the
defaults setup for the PRI
Laurent a écrit :
...
I read somewhere (can't remember where, sorry) that double
framing is equivalent to basic framing. Presumably it is also
equivalent to no crc. If that's correct, then I would say you
can use the same setup as you have with FT, it looks good to me.
Ok, thanks
As
Le 19.01.2009 08:50, Benoit a écrit :
Laurent a écrit :
Well, the telcos techs said a straight cable should do the trick, but
since i didn't get any isdn link up
with the straight, i built a crossover like what you described, with no
luck either.
Did you check (like with a
Laurent a écrit :
Those terms would be ISDN-related. VN4 is Version Number 4, and
ETSI is the European standards-adopting organization for telecoms.
So you might want to check for E1 support (ISDN in Europe,
basically) if you want to connect a PRI-capable equipment - I
assume that's what you
Benoit a écrit :
Laurent a écrit :
Those terms would be ISDN-related. VN4 is Version Number 4, and
ETSI is the European standards-adopting organization for telecoms.
So you might want to check for E1 support (ISDN in Europe,
basically) if you want to connect a PRI-capable equipment - I
Hi,
Our potentiel next phone provider ask me a question i can't answer for sure,
maybe someone here knows ?
He says that is equipement only support VN4 protocol or more, or ETSI,
however i can't find matching terms in the digium documentation or
the chan_dahdi/dahdi/system.conf files...
Any
On Thu, Jan 15, 2009 at 06:11:59PM +0100, Benoit wrote:
Hi,
Our potentiel next phone provider ask me a question i can't answer for sure,
maybe someone here knows ?
He says that is equipement only support VN4 protocol or more, or ETSI,
however i can't find matching terms in the digium
Le 16.01.2009 04:11, Benoit a écrit :
Hi,
Our potentiel next phone provider ask me a question i can't answer for sure,
maybe someone here knows ?
He says that is equipement only support VN4 protocol or more, or ETSI,
however i can't find matching terms in the digium documentation or
the
19 matches
Mail list logo
