opaqueice;234637 Wrote:
Haha, that's funny... I thought exactly the same thing when I read that
post! I had a little of that sinking feeling I get at cocktail parties
when someone finds out I'm a physicist and brings up QM - that
Phil Leigh;234683 Wrote:
start with a CD track - so we know exactly what the bits are. put
through a good DAC and analogue interconnects to a suitable high
quality and calibrated ADC - record the bits. Compare the recorded bits
with the original bits. Any change must be induced by the cable.
[EMAIL PROTECTED];234768 Wrote:
I cant believe this is a ground loop issue as my sb3 or sb2 dont have
this issue when connected to these systems.
I don't know for sure, but considering the Transporter's mains
connection is a 3-pin affair, it's likely that it is indeed grounded. I
think your
I went thru all this too when I got my Lavry DA10.
The good thing is that the DA10 has internal jumpers which change the
output from balanced to unbalanced - manual extract:
-
The unit is factory configured to operate in Balanced output mode. The
balanced signal comes out PIN 2
Hello
Is it worth while to use this DAC with SB3?
http://www.audiocircle.com/circles/index.php?topic=45628.0
Thanks in advance
--
TheBas
TheBas's Profile: http://forums.slimdevices.com/member.php?userid=7170
View this
Thanks mr-b.
I have no intention of using balanced output.
From what I understand so far the easiest thing would be to leave the
jumpers in the factory setting (balanced) but use an XLR-RCA adapter
that does not have the -ve connected to anything, to get the correct
unbalanced operation.
Can't see any obvious reason why not.
the nos dac's should be fine too. my low cost fav is the behringer src
2496
--
zanash
Acoustician and builder of interesting cables
zanash's Profile:
DennyL;234072 Wrote:
I bought three homeplugs for my Squeezebox 3. They worked straight away
with no struggle. After about twenty minutes the music stopped, and the
server could no longer find the Squeezebox, so now I'll sell the
homeplugs and I'm back to Ethernet. (Don't talk about
I bought the Bryston off of Audiogon, where the seller listed it as the
B100DA (which has an integrated DAC board). It was a beautiful piece of
equipment, and I set it up in my system, but there was no DAC installed!
The seller screwed up the listing, and I couldn't justify spending that
much for
Something else the JUMPERS may be doing is changing the level. There is
nothing wrong with an unbalanced signal! Chances are the output
impedance of the Lavry is 100-ohms, so distance isn't a problem
either.
Unbalanced usually is very bad coming out of most consumer products at
a much higher
Skittler;234854 Wrote:
Do XLR-RCA adapters have it connected or not?
Again, it depends if it is male or female.
If it looks like this, the negative line should be not connected:
http://img.luthman.se/ProductImages/WebSize/103481.jpg
And if it looks like this it should be tied to ground:
TheBas;234847 Wrote:
Hello
Is it worth while to use this DAC with SB3?
http://www.audiocircle.com/circles/index.php?topic=45628.0
Thanks in advance
Seems ok, but unless it does reclocking it will not fix the minor
jitter problems that the SB3 has. I doubt it will be an improvement
Hi, I just ran into this thread, apparently several months late.
I have to agree about some of the problems that some have had with my
DiffMaker program. In some setups, a good clean null is achieved when
it should be (i.e., when two recordings recorded the same way are
diffed). In others, the
How well Homeplugs works does seem to vary depending on the house
wiring. We recently moved and whereas I could drive multiple SB3s at
the old place, I now struggle to drive two and get intermittent
dropouts (very old house). I also find that they seem to work better
in some rooms compared with
bwaslo,
Try these:
http://www.soundkeeperrecordings.com/format.htm
--
CPC
CPC's Profile: http://forums.slimdevices.com/member.php?userid=12336
View this thread: http://forums.slimdevices.com/showthread.php?t=37352
well i've gone and ordered the Concept and a Toslink cable for my
SB3.
the Ikemi and Pekin went on Ebay todayi was not using them at
all.
i will put some of the proceeds towards a Nas server of some sort(which
has to work with Vista Ultimate),once i've digested all the posts on
this
sounds like the preamp/receiver might be the culprits here,what kind of
transformer do they use?.i used to have terrible system hum annoyingly
coming thru' my speakers.my Linn Preamp and amplifiers used toroidal
transformers,so i got a friendly sparks to put in a separate spur which
kindof
How about this one?:
http://cgi.ebay.com/brand-new-dac-3-24-BIT-192-KHZ-ak4394-TUBE-DAC-BOX_W0QQitemZ180168383260QQihZ008QQcategoryZ3280QQcmdZViewItem
Thanks
TheBas
--
TheBas
TheBas's Profile:
dennis55;234996 Wrote:
sounds like the preamp/receiver might be the culprits here,what kind of
transformer do they use?.i used to have terrible system hum annoyingly
coming thru' my speakers.my Linn Preamp and amplifiers used toroidal
transformers,so i got a friendly sparks to put in a
Auronthas save yourself the hassle and buy a Transporter used or new.if
you get the source right first then reap the benefit in the long run. i
have a Linn Sondek LP12 here with all the upgrades apart from Keel/Ekos
se and it plays good music thru' ANY speakers you hook up to it.
Just my tuppence
20 matches
Mail list logo
