Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
Many thank Justin. This is very helpful. Best regards Paul Onwude (Please excuse the brevity of this email as it was sent via a mobile device. Kindly excuse misspelled words or sentence structure) On 4 Nov, 2013, at 7:28 pm, Justin Carney justin.s.car...@gmail.com wrote: If you're adding the plus I cucm this is expected behavior that it will be lost at the ios gw. You're not missing anything on cucm, this is just how h323 works on ios routers...the only option is to add a plus in the ios gateway. IOS/h323 will (by design, unfortunately) discard a plus in dnis on the inbound call leg, so make sure you are adding it on the outbound dial or voice port. (You might be able to add plus on an inbound dial peer but I haven't tried and not sure if it would then get discarded.) For the lab I would recommend doing ALL h323 digit manipilation on the h323 gw. If you do it in cucm then later when you need to do srst you will need extra dialpeers and/or translations. For example, I use only 4 outbound pots dialpeers in h323 each with a translation profile that modifies ani (for each site, matching 2... 3... and 4...) and dnis (usually just type/plan). I send all the dialed digits from a phone to the h323 gw the let the gw make the ani and dnis match the pstn requirements for all call types including teho. The only time I modify digits in cucm is when no new rp is alowed for 911 at site b and that uses slrg - the ani is masked to 7digits in cucm, but the h323 still must set ani/dnis type and plan to unknown for dnis. Also, for teho from site a to site b pstn, I would strip the 91408 from the dialed digits and prefix 9 in the route list/rg for h323 so it matches my outbound local dialpeer. Hope this helps. -Justin On Nov 4, 2013 2:19 AM, Paul Onwude ponw...@gmail.com wrote: Hi All. Need expert opinion on this. I have a H323 gateway and i have setup called party transformations on CUCM to send “+” to the gateway. My issue is i don’t see the plus when i debug ids q931. When i do other digit manipulation like adding “#”, it show up on the gateway but not the “+” I know i can probably achieve this using translation on the GW but i can’t help but think there is something i am missing in CUCM. Any ideas?? Paul ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
If you're adding the plus I cucm this is expected behavior that it will be lost at the ios gw. You're not missing anything on cucm, this is just how h323 works on ios routers...the only option is to add a plus in the ios gateway. IOS/h323 will (by design, unfortunately) discard a plus in dnis on the inbound call leg, so make sure you are adding it on the outbound dial or voice port. (You might be able to add plus on an inbound dial peer but I haven't tried and not sure if it would then get discarded.) For the lab I would recommend doing ALL h323 digit manipilation on the h323 gw. If you do it in cucm then later when you need to do srst you will need extra dialpeers and/or translations. For example, I use only 4 outbound pots dialpeers in h323 each with a translation profile that modifies ani (for each site, matching 2... 3... and 4...) and dnis (usually just type/plan). I send all the dialed digits from a phone to the h323 gw the let the gw make the ani and dnis match the pstn requirements for all call types including teho. The only time I modify digits in cucm is when no new rp is alowed for 911 at site b and that uses slrg - the ani is masked to 7digits in cucm, but the h323 still must set ani/dnis type and plan to unknown for dnis. Also, for teho from site a to site b pstn, I would strip the 91408 from the dialed digits and prefix 9 in the route list/rg for h323 so it matches my outbound local dialpeer. Hope this helps. -Justin On Nov 4, 2013 2:19 AM, Paul Onwude ponw...@gmail.com wrote: *Hi All. * *Need expert opinion on this.* *I have a H323 gateway and i have setup called party transformations on CUCM to send “+” to the gateway. My issue is i don’t see the plus when i debug ids q931. When i do other digit manipulation like adding “#”, it show up on the gateway but not the “+”* *I know i can probably achieve this using translation on the GW but i can’t help but think there is something i am missing in CUCM.* *Any ideas??* *Paul* ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
Hi All. Need expert opinion on this. I have a H323 gateway and i have setup called party transformations on CUCM to send “+” to the gateway. My issue is i don’t see the plus when i debug ids q931. When i do other digit manipulation like adding “#”, it show up on the gateway but not the “+” I know i can probably achieve this using translation on the GW but i can’t help but think there is something i am missing in CUCM. Any ideas?? Paul___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
Hi Adam, I found this in CCM service settings for some of H323 parameters : Ensure that calls over QSIG trunks do not utilize + because it is not supported by QSIG. This parameter has no effect on H.323 outbound calls because H.323 unconditionally strips the + sign when routing outbound calls. This is a required field. Default: False Best regards Andriy 2011/3/24 adam compton com...@gmail.com I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
it's fine on SIP, it's only h323 that can't handle the + sign. and it's not a dial-peer that strips it, when call manager sends the h225 setup, + is already NOT present there... Regards, On Thu, Mar 24, 2011 at 2:08 AM, Adam Thompson phoe...@fatturtle.comwrote: The + gets stripped by the voip dial-peer. You will always have to add the + back when sending to a H323 or SIP gateway. -Adam On Wed, Mar 23, 2011 at 8:19 PM, adam compton com...@gmail.com wrote: Well, I might have found my answer: http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002862 Poster says that h323 gateways can't process the plus. Can anyone confirm? Adam Compton On Wed, Mar 23, 2011 at 8:15 PM, adam compton com...@gmail.com wrote: I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
This has been a pretty long discussion about the normal behaviour of H323. The '+' expression is recognised by MGCP and SIP GWs, not H323. If you want an H323 GW to send the full E164 number starting with '+' you need to apply a voice translation rule. For example you can apply the rule on the voice port in outgoing direction. Example voice translation rule is: voice translation-rule 10 rule 1 // /+/ voice translation-profile AddPlus translate called 10 voice-port 0/0/0:23 translation-profile outgoing AddPlus Do the above and you will be sending the full number across. and some say to add type unknown unknown plan any isdn to the rule 1 listed here On Thu, Mar 24, 2011 at 5:03 AM, George Goglidze gogli...@gmail.com wrote: it's fine on SIP, it's only h323 that can't handle the + sign. and it's not a dial-peer that strips it, when call manager sends the h225 setup, + is already NOT present there... Regards, On Thu, Mar 24, 2011 at 2:08 AM, Adam Thompson phoe...@fatturtle.com wrote: The + gets stripped by the voip dial-peer. You will always have to add the + back when sending to a H323 or SIP gateway. -Adam On Wed, Mar 23, 2011 at 8:19 PM, adam compton com...@gmail.com wrote: Well, I might have found my answer: http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002862 Poster says that h323 gateways can't process the plus. Can anyone confirm? Adam Compton On Wed, Mar 23, 2011 at 8:15 PM, adam compton com...@gmail.com wrote: I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
one small correction. It would be translate calling since we are talking about callerid. On Thu, Mar 24, 2011 at 8:20 AM, Bill Lake whl...@gmail.com wrote: This has been a pretty long discussion about the normal behaviour of H323. The '+' expression is recognised by MGCP and SIP GWs, not H323. If you want an H323 GW to send the full E164 number starting with '+' you need to apply a voice translation rule. For example you can apply the rule on the voice port in outgoing direction. Example voice translation rule is: voice translation-rule 10 rule 1 // /+/ voice translation-profile AddPlus translate called 10 voice-port 0/0/0:23 translation-profile outgoing AddPlus Do the above and you will be sending the full number across. and some say to add type unknown unknown plan any isdn to the rule 1 listed here On Thu, Mar 24, 2011 at 5:03 AM, George Goglidze gogli...@gmail.com wrote: it's fine on SIP, it's only h323 that can't handle the + sign. and it's not a dial-peer that strips it, when call manager sends the h225 setup, + is already NOT present there... Regards, On Thu, Mar 24, 2011 at 2:08 AM, Adam Thompson phoe...@fatturtle.com wrote: The + gets stripped by the voip dial-peer. You will always have to add the + back when sending to a H323 or SIP gateway. -Adam On Wed, Mar 23, 2011 at 8:19 PM, adam compton com...@gmail.com wrote: Well, I might have found my answer: http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002862 Poster says that h323 gateways can't process the plus. Can anyone confirm? Adam Compton On Wed, Mar 23, 2011 at 8:15 PM, adam compton com...@gmail.com wrote: I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
Well, I might have found my answer: http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002862 Poster says that h323 gateways can't process the plus. Can anyone confirm? Adam Compton On Wed, Mar 23, 2011 at 8:15 PM, adam compton com...@gmail.com wrote: I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
Adam, This is correct. If you have a requirement to send the + you'll have to add at voice-port using a translation-rule. Jeff From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of adam compton Sent: Wednesday, March 23, 2011 5:19 PM To: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls Well, I might have found my answer: http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002862 Poster says that h323 gateways can't process the plus. Can anyone confirm? Adam Compton On Wed, Mar 23, 2011 at 8:15 PM, adam compton com...@gmail.com wrote: I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] H323 gateway doesn't send the plus on outgoing PRI calls
The + gets stripped by the voip dial-peer. You will always have to add the + back when sending to a H323 or SIP gateway. -Adam On Wed, Mar 23, 2011 at 8:19 PM, adam compton com...@gmail.com wrote: Well, I might have found my answer: http://www.voiceie.com/cgi-bin/ultimatebb.cgi?ubb=get_topic;f=8;t=002862 Poster says that h323 gateways can't process the plus. Can anyone confirm? Adam Compton On Wed, Mar 23, 2011 at 8:15 PM, adam compton com...@gmail.com wrote: I'm using external calling number mask with full e164 number. When I call from an extension out a MGCP gateway, the call goes as expected with the +. If I dial out of an H323 gateway, the external number shows with no plus. Anybody ran into this before? I can add the plus with a translation-profile on the voice-port, but in the back of my head, I feel i must be doing something wrong on the Call Manager side of things. Adam Compton ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com