Hello List,
I have a router which is overloaded. His processor goes up to 99% load.
When issuing a sh proc cpu command, the one with the higgest load is the
Crypto PAS Proc.
Do you have a hint?
#sh proc cpu | begin crypto
188 479 50 0.00% 0.00% 0.00% 0 crypto
Hi all,
I do traffic shaping on a 7206 box, eg:
a: 10Mbps for one class
b: 15Mbps for another class
c: 20Mbps for another class
If c: only use 10Mbps, how can I share it to a: and b:?
How can I monitor (graph) the bandwidth usage for the 3 classes?
Best Regards.
I was thinking about getting a refreshed CCNA certification sometime, my
original cert ran out a while ago ... (luckily, my knowledge of Cisco
routers didn't expire with it ;) )
Anyway, I remember Cisco was (or had just did) an update on their CCNA
tests back then. I also remember that the
Hi,
If c: only use 10Mbps, how can I share it to a: and b:?
I would say that if your classes are Class Based Weighted Faire Queuing.
How can I monitor (graph) the bandwidth usage for the 3 classes?
You can graph each class using MRTG and the relevant OID
(.1.3.6.1.4.1.9.9.166.1.15.1.1.7.x.y,
http://www.cisco.com/web/learning/le3/current_exams/640-802.html
:tele
On Tue, 2008-01-08 at 13:16 +0100, Garry wrote:
I was thinking about getting a refreshed CCNA certification sometime, my
original cert ran out a while ago ... (luckily, my knowledge of Cisco
routers didn't expire with
Hello,
We have a strange problem with a 3560-8PC router
(c3560-advipservicesk9-mz.122-37.SE1). Which kills three times the
uplink Port from a 2960. It looks like a power over ethernet problem
which accour if you power off the 2960. The port is configured like
this:
interface FastEthernet0/1
Hi,
Using wfq (ie class based shaping) :
To illustrate, lets suppose the following weight for each queue, a:1 b:2 c:3
If total bandwith doesn't exceed 45Mbps, no congestion: each queue can manage
its bandwith.
If total amount of bandwith 45Mbps exceed, wfq gives a weight to each queue,
In
On 1/8/08, Rivo Tahina RAZAFINDRATSIFA [EMAIL PROTECTED] wrote:
Hi all,
I do traffic shaping on a 7206 box, eg:
a: 10Mbps for one class
b: 15Mbps for another class
c: 20Mbps for another class
If c: only use 10Mbps, how can I share it to a: and b:?
maybe this help
policy-map PMAP1
class
On Tue, Jan 08, 2008 at 01:38:44PM +0300, Rivo Tahina RAZAFINDRATSIFA wrote:
Hi all,
I do traffic shaping on a 7206 box, eg:
a: 10Mbps for one class
b: 15Mbps for another class
c: 20Mbps for another class
If c: only use 10Mbps, how can I share it to a: and b:?
How can I monitor (graph)
Suitable not to forget to enable persistence of ifindex and cbqos objects index
otherwise your brain will be damaged so as irreversible :-)
HiH and HnY
Rachid
-Message d'origine-
De : [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] De la part de Jean-Christophe
Varaillon
Envoyé : mardi 8
Cisco IP SLAs TCP Connect operation may fit your bill.
http://www.cisco.com/go/ipsla
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Ali, Rijas: BB
UAE (IT)
Sent: Monday, January 07, 2008 5:57 AM
To: cisco-nsp@puck.nether.net
Subject: [c-nsp] Telnet
On Tue, Jan 08, 2008 at 07:45:11AM -0800, Mark Kent wrote:
So, I'm looking at the cisco web pages and I see the 7600 is
pushed big-time as a service provider edge device, and yet I see
that the sup32-3b has a 300Mhz processor, and so it is not
much faster than an NPE-300 (262Mhz).
I stopped
Thanks for the response, you guys gave me a bunch of ideas and i finally
figure out the problem.
The last length of fiber was Multimode, or is bad, i moved the entire router
back one fiber jump and i'm rockin in the 10/10mb world now.. No errors,
this DS3 is solid. Unfortionally the fiber
On Tue, 2008-01-08 at 07:45 -0800, Mark Kent wrote:
So, I'm looking at the cisco web pages and I see the 7600 is pushed
big-time as a service provider edge device, and yet I see that the
sup32-3b has a 300Mhz processor, and so it is not much faster than an
NPE-300 (262Mhz).
I stopped
So I can easily scp an image from my workstation onto a router. But I
cannot seem to scp IOS files between routers (sup720s, SRB2 code). Am
99% certain I did so in the past, but no amount of monkeying could get
it to work recently. Failure indication varies (it happens
immediately), but it
Peter Rathlev wrote:
With 512MB memory, it can't take a full table? The world is moving fast
I guess. :-)
Not the memory is the issue, but TCAM size and on the Sup32 it can't
take full routes anymore (as it's limited to 239k routes, iirc).
___
At 06:32 PM 1/8/2008 +0100, Peter Rathlev wrote:
On Tue, 2008-01-08 at 07:45 -0800, Mark Kent wrote:
So, I'm looking at the cisco web pages and I see the 7600 is pushed
big-time as a service provider edge device, and yet I see that the
sup32-3b has a 300Mhz processor, and so it is not much
At 06:32 PM 1/8/2008 +0100, Peter Rathlev wrote:
On Tue, 2008-01-08 at 07:45 -0800, Mark Kent wrote:
So, I'm looking at the cisco web pages and I see the 7600 is pushed
big-time as a service provider edge device, and yet I see that the
sup32-3b has a 300Mhz processor, and so it is not much
On Tue, 2008-01-08 at 19:46 +0200, Eugeniu Patrascu wrote:
Not the memory is the issue, but TCAM size and on the Sup32 it can't
take full routes anymore (as it's limited to 239k routes, iirc).
On Tue, 2008-01-08 at 09:50 -0800, Ian Cox wrote:
It forwards in hardware if the FIB will fit into
Hi,
7600 is a hardware forwarding platform(basically a catalyst 6500), whereas the
7200 is processor based.
The 7600 can forward much much more traffic.
With full routes however the sup-32 isn't going to cut it you need the 720 with
PFC3BXL.
The sup32 doesn't have enough tcam space for full
Ian Cox wrote:
It forwards in hardware if the FIB will fit into the hardware FIB
table. The full internet table will not fit into a
PFC2/PFC3a/PFC3b/FFC3a/DFC3b/PFC3C/DFC3C anymore since the hardware
table, even after changing from the default will only get you 239k
routes. For full
If you don't use XLs and then you wind up with FIB exception and
packets forwarded in software.
Packets for those routes that haven't been installed in the FIB...
I'm probably a bad person for asking, and not first searching, but can
someone remind me what happens when the FIB fills - what
[EMAIL PROTECTED] wrote:
There has been alot of talk about this on the list
yeah, but it's nice to get it boiled down to the essentials,
like you and others did.
Thanks,
-mark
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
Does anyone have real-life experience with driving a full DS3's worth of
bandwidth through the 3845? The website says it will, but I don't know
if that's yes, as long as it's a single flow or yes, even for worst
case traffic or something in the middle. Thanks!
~Seth
On 1/8/08, Seth Mattinen [EMAIL PROTECTED] wrote:
Does anyone have real-life experience with driving a full DS3's worth of
bandwidth through the 3845? The website says it will, but I don't know
if that's yes, as long as it's a single flow or yes, even for worst
case traffic or something in the
Jeffrey Ollie wrote:
On 1/8/08, Seth Mattinen [EMAIL PROTECTED] wrote:
Does anyone have real-life experience with driving a full DS3's worth of
bandwidth through the 3845? The website says it will, but I don't know
if that's yes, as long as it's a single flow or yes, even for worst
case
Say you want to scp ios from router 1 onto router 2 disk2:
on router 2 set up
aaa new-model
aaa authentication login default local
aaa authorization exec default local
username steve priviledge 15 password steve
then on router 1 where you have the ios:
copy disk2:iosimage.bin scp://[EMAIL
On Mon, 7 Jan 2008, Jon Lewis wrote:
On Mon, 7 Jan 2008, Jared Mauch wrote:
I've never tried anything greater than 1G.
I can report now that 2GB cards work properly, both with 12.2SXF and
12.2SXD.
--
Jon Lewis
On Tue, 2008-01-08 at 09:47 -0800, Raymond, Steven wrote:
So I can easily scp an image from my workstation onto a router. But I
cannot seem to scp IOS files between routers (sup720s, SRB2 code). Am
99% certain I did so in the past, but no amount of monkeying could get
it to work recently.
On Tue, Jan 08, 2008 at 10:14:09AM -0800, Mark Boolootian wrote:
If you don't use XLs and then you wind up with FIB exception and
packets forwarded in software.
Packets for those routes that haven't been installed in the FIB...
Switched to the floor if you are unlucky enough in topology
I have no problems logging in w/ SSH. And the problems are the same
when
copying from a a Linux shell.
Maybe SRB is just being stupid. :-)
Agreed. Further testing this morning shows I can send from SRB2 to SRA2
just fine, but from the very same router running SRB2 to another router
running
Hi,
On Tue, Jan 08, 2008 at 02:33:00PM +, [EMAIL PROTECTED] wrote:
helps people pass exams, but from listening to friends complain
about cisco exams, it's usually been an issue of comprehension than
incorrect answers or to many right answers.
Do they still ask about Class B networks, and
Gert Doering wrote:
Hi,
On Tue, Jan 08, 2008 at 02:33:00PM +, [EMAIL PROTECTED] wrote:
helps people pass exams, but from listening to friends complain
about cisco exams, it's usually been an issue of comprehension than
incorrect answers or to many right answers.
Do they still ask
msdp peering between border RPs could fit your need.
HiH
Rachid
-Message d'origine-
De : [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] De la part de James Slepicka
Envoyé : mardi 8 janvier 2008 21:06
À : cisco-nsp@puck.nether.net
Objet : [c-nsp] auto-rp/bsr for external RPs
Hello all,
On Tue, 2008-01-08 at 22:51 +0100, Gert Doering wrote:
Do they still ask about Class B networks, and how many subnets of
16 hosts can you put into a Class C (ignoring the now-default of
ip subnet-zero) and such crappy stuff?
I may be pedantic now (it' getting late!), but ip subnet-zero
Hi,
Apologies for the off-topic post, but I figured there'd be a few fibre
optic guru nerd types out there.
I need to connect some equipment (a router to a switch) via a dark
fibre service. At each end, the service is presented as TX and RX on
an optical circulator -- the fibre run itself is a
Hi,
I may be pedantic now (it' getting late!), but ip subnet-zero doesn't
change the number of hosts you can cram into an unsubnetted /24
network, class C or otherwise, does it? As I understand it, it just
pretty much right - it allows you to use some freaky /24's within your
available space
Peter Rathlev wrote:
Um... EIGRP is still semi-widely used last time I checked. It's a
complex protocol, but things like unequal cost multipath makes it well
worth knowing. And it was OSPF and BGP that took up by far the largest
part of my exam, but maybe I was just lucky. :-)
That may be but
As I recall from a couple years ago (maybe three even at this point) there was
a bunch of that how many subnets of size X can you fit in a /Y? Lot of look at
this STP topology and tell us what will happen if event K occurs too.
Thanks,
Brian Desmond
[EMAIL PROTECTED]
c - 312.731.3132
On Tue, Jan 08, 2008 at 02:33:00PM +, [EMAIL PROTECTED] wrote:
their website. I'm not a trainer or someone that helps people pass
exams, but from listening to friends complain about cisco exams, it's
usually been an issue of comprehension than incorrect answers or to
many right answers.
On Tue, Jan 08, 2008 at 11:17:51PM +, [EMAIL PROTECTED] wrote:
available space - but its more important when using /23's and the
like where you can use .0 and .255 addresses within the space.
I've found that there are an awful lot of (mis?)configured routers and
hosts out there which will
Hi all,
I'm having some interesting fun with getting a CSS to log what I'm after to
my syslog server.
I see messages getting through, for example a service going down etc..
however I'd also like to log when the service comes back up and I haven't
quite found teh correct knobs to tweak to get
Hi Everyone,
I am hoping someone can help me out here. We have an old legacy network
which is just a flat L2 network across multiple sites connected by
fibre. For various reasons this fibre will no longer be available for
use, so I need to find another way to keep this L2 network intact. There
So I'm having a heck of a time trying to get a big file onto either
the bootflash or disk0 of a SUP720. The tftp never finishes and spits
an error back (can't present the error message at the moment).
A quick search showed some results circa 2000 which large files and
solaris had issues,
That would be a great application for l2tpv3, assuming you don't need to
move a huge amount of data and don't have MPLS enabled.
Hit me up off-list for the config examples.
John van Oppen
Spectrum Networks LLC
206.973.8302 (Direct)
206.973.8300 (main office)
-Original Message-
From:
probably not the answer you want to hear...Run an RP for *all* groups
on a router you control
Actually, this is what I'm doing now -- all of my routers are pointing
to an anycast RP for internal groups.
run MSDP between your RP and the upstream RP
Unfortunately, the third party won't run MSDP
On Jan 8, 2008 2:58 PM, Justin Shore [EMAIL PROTECTED] wrote:
Peter Rathlev wrote:
Um... EIGRP is still semi-widely used last time I checked. It's a
complex protocol, but things like unequal cost multipath makes it well
worth knowing. And it was OSPF and BGP that took up by far the largest
You can also look at QinQ tunneling. But really that just extends the
pain. It might be more worth your time to deal with the flat layer 2
network.
On Jan 8, 2008 5:47 PM, Geyer, Nick [EMAIL PROTECTED] wrote:
Hi Everyone,
I am hoping someone can help me out here. We have an old legacy
Jason Lixfeld wrote:
So I'm having a heck of a time trying to get a big file onto either
the bootflash or disk0 of a SUP720. The tftp never finishes and spits
an error back (can't present the error message at the moment).
I have something in the back of my mind where TFTP was limited to
On 9-Jan-08, at 12:29 AM, Garry wrote:
Jason Lixfeld wrote:
So I'm having a heck of a time trying to get a big file onto
either the bootflash or disk0 of a SUP720. The tftp never
finishes and spits an error back (can't present the error message
at the moment).
I have something in the
Hi,
On Tue, Jan 08, 2008 at 11:17:51PM +, [EMAIL PROTECTED] wrote:
I may be pedantic now (it' getting late!), but ip subnet-zero doesn't
change the number of hosts you can cram into an unsubnetted /24
network, class C or otherwise, does it? As I understand it, it just
pretty much
Hi,
On Tue, Jan 08, 2008 at 11:36:18PM +0100, Peter Rathlev wrote:
On Tue, 2008-01-08 at 22:51 +0100, Gert Doering wrote:
Do they still ask about Class B networks, and how many subnets of
16 hosts can you put into a Class C (ignoring the now-default of
ip subnet-zero) and such crappy
52 matches
Mail list logo
