Re: Stus-List Gotta Love These Hurricanes

Good luck, you guys. You have had repeated beatings this year. Jim Watts Paradigm Shift C 35 Mk III Victoria, BC On 7 October 2017 at 19:56, Bob Caughran via CnC-List wrote: > Thanks Dennis. Just got word that there's 76 boats in the cove now > including the biloxi

Re: Stus-List Gotta Love These Hurricanes

Thanks Dennis. Just got word that there's 76 boats in the cove now including the biloxi schooners so I suspect we picked the right spot. Touché going to get rocked from the way it looks too. Fingers crossed for all boats. Should have word early tomorrow on Beemers fate. Bob Caughran Beemer,

Re: Stus-List C 30 MK1 Shade

Thanks Aaron! From: Aaron Rouhi [mailto:admiralmag...@outlook.com] Sent: Saturday, October 7, 2017 7:39 AM To: cnc-list@cnc-list.com Subject: Re: Stus-List C 30 MK1 Shade I have a Bimini and Dodger on my 30-1. The Bimini is made by Genco Marine (they have made tons of these for C have

Re: Stus-List Foam in mast

I wouldn't use any chemical solvents. The risk to the insulation on your wires and the possibility of a gooey mess are considerations. You said it was just above halyard exits? If you don't pull the rig, think about modifying a drain snake. They're fairly cheap. Perhaps take a 1/4 inch snake,

Re: Stus-List Gotta Love These Hurricanes

Bob, was wondering about Beemer. Beemer is probably the most exposed boat on the list. Hope it weathers the storm OK. Let us know. As I was driving to Pensacola I saw a couple of shrimpers up the Biloxi backwaters by one of the I-10 bridges. Many marinas on the coast boot out their tenants.

Re: Stus-List Spreader boots 1984 C 35-3

Edson elkhide spreader boots are available at West Marine for about $70 per pair, which is about twice the price of the Taylor Made nylon boots. The boots on my lower spreaders (where there is contact with the headsail) are elk hide. The boots on the uppers (which are above the leach of the

Stus-List Gotta Love These Hurricanes

So here's how my last 3 days have gone. On Thursday a fellow sailor from my marina in Biloxi called to let me know they were considering closing the marina for Nate. I packed up my car and headed down to Biloxi yesterday morning. Sunshine, 82 degrees and 12-15 knots from the east. I arrive to

Re: Stus-List Spreader boots 1984 C 35-3

I would regard that as a bargain. I think the guys at Blackline are pretty good, but expensive. Jim Watts Paradigm Shift C 35 Mk III Victoria, BC On 7 October 2017 at 18:11, Andrew Burton via CnC-List < cnc-list@cnc-list.com> wrote: > I just did the rigging on Peregrine. The riggers were able

Re: Stus-List Spreader boots 1984 C 35-3

I just did the rigging on Peregrine. The riggers were able to re-head all but the V2/D3, which had to be replaced because of aligning the top spreaders with the bend in the rod. The cost was about $5k for literally the best guys in the world to do it all. Andy C 40 Peregrine Andrew Burton 61

Re: Stus-List Spreader boots 1984 C 35-3

Try Leitch and McBride, Jim. They should have some. Tell Phil and Rick I said hi. Andy C 40 Peregrine Andrew Burton 61 W Narragansett Newport, RI USA02840 http://sites.google.com/site/andrewburtonyachtservices/ +401 965-5260 > On Oct 7, 2017, at 20:39, Jim Watts via CnC-List

Stus-List Foam in mast

I hope this is a common issue, and someone has found an answer. Our old 29-2 and our current 35-3 both have some sort of foam in the mast above the top halyard exit plate. I was really lucky that I pulled a bundle of new wires through the foam on the 29, it was really touch and go as to whether my

Re: Stus-List Spreader boots 1984 C 35-3

I'm having a rigger come out next week to have a look at our standing rigging and mast, it's all original so I'm sure we'll end up with yet another horrific bill. I'm seriously considering going to wire instead of rod, but I'll get quotes on both Andrew, you're right, I want to pull the mast so I

Stus-List C 35-3 Rudder Drain Holes

Neil: There is probably no one simple answer to your question with water intrusion in a ruddera hole or two drilled into the bottom of the rudder is always a good place to start. In my case, my rudder was rebuilt by the original owner just before I acquired the boat. Nevertheless,

Re: Stus-List C 35-3 Rudder Drain Holes

We drain the rudder on the 27-3 as follows. Make 3 drain holes, one high up on the trading edge of the rudder, one 3-4 inches from the tip, and one on the bottom of the rudder. We drilled 1/4 in holes and then tapped them to accept hex-head cap screws. Water comes out in the fall, cold weather

Re: Stus-List C 35-3 Rudder Drain Holes

Neil, My 35-1 came with holes already drilled, on the side in the lower aft corner. I put 4200 in them in the spring, remove it in the fall. Neil Gallagher Weatherly, 35-1 Glen Cove, NY On 10/7/2017 3:55 PM, schiller via CnC-List wrote: One of the items in our new C 35, Mark III was that

Stus-List C 35-3 Rudder Drain Holes

One of the items in our new C 35, Mark III was that there was moisture in the rudder and the surveyor suggested drilling drainage holes.  Anyone want to suggest the location to drill?  We hauled out last night and I am going up to the boat to disconnect batteries on Wednesday.  I assume that

Re: Stus-List Spreader boots 1984 C 35-3

Especially if you intend to pull the rig, Jim, sewing elkhide boots on is remarkably easy. I did that last year with mine and even though I though I made a hash of the job, you wouldn't know it from the deck! Mind you, I did start with the top set of spreaders first. It's a quick enough job

Stus-List Spreader boots 1984 C 35-3

Does anyone know offhand the sizes of the spreader tips on the early rig (pre-1985)? I want to put on some spreader boots and having them ready to go would make it much easier than having to go up and measure first. Jim Watts Paradigm Shift C 35 Mk III Victoria, BC

Stus-List Fwd: Annapolis Boat Show Sale!!

Fall Annapolis Show Sale At Defender Marine Outfitters! *Click on text and images below to discover some Great Deals. *Can't view the images? Click here

Re: Stus-List C 30 MK1 Shade

I sent you a photo of the set up on my 30 . I have a removable panel between the dodger and Bimini for the main sheet while sailing . I had a handle across the rear of the dodger and one on each side also . I have side gates in my lifelines. It helps when getting on board Sent from Joe Bognar

Re: Stus-List Re George Cuthbertson

Joe Photos sent and a great idea. Many thanks for pulling this together John and Maryann Read Legacy III 1982 C 34 Noank, CT From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Joe Della Barba via CnC-List Sent: Friday, October 06, 2017 10:07 AM To:

Re: Stus-List C 30 MK1 Shade

I have a Bimini and Dodger on my 30-1. The Bimini is made by Genco Marine (they have made tons of these for C have patterns on file) and Dodger is custom made locally by Bacon Sails. The Bimini is attached to the rail and has slots for my double backstay adjustor... I will dig up some photos

Re: Stus-List C 30 Shade

I have both a dodger and a Bimini on my 30. The Bimini frame is attached to the rear pulpit. It will provide shade for the helmsman and extends from the rear of the boom back to the stern. Rick C 30 ___ The bills have started coming in for the

Re: Stus-List Annapolis boat show.

I’m working at the show in Tent C with my dealer Sail Care through Sunday afternoon. Saw Joel yesterday when he stopped by. Chuck Gilchrest S/V Half Magic 1983 35 LF Padanaram,MA Sent from my iPhone > On Oct 6, 2017, at 10:59 AM, Della Barba, Joe via CnC-List > wrote: