Re: Stus-List Merriman snatch block question
Thanks for the follow up. No rub rail (at all) on a Custom 42. From: Rick Brass via CnC-List Sent: Thursday, April 11, 2019 8:59 PM To: cnc-list@cnc-list.com Cc: Rick Brass Subject: Re: Stus-List Merriman snatch block question Has not happened on my 38. I have a pair of 70 series single blocks on swivel shackles permanently mounted to the toe rail aft of the winches that I use as turning blocks to get a good sheet lead into the winches (which really helps reduce the loads when moving the line adjustable genoa cars). And about 4 holes aft of the turning blocks are a pair of the 70 series snatch blocks for the spin sheets. I normally try to position the snatch blocks inboard with the cheeks on the top side to make line handling easier – but I’m old and forgetful so they often end up hanging on the outside of the toe rail when at the dock. In the spirit of full disclosure, my rubrail is a strip of HMWPE that was added to the hull in place of the original rubber rail, and it sticks out an inch or so further than the rubber rail that was typical of the 70s and 80s models. When the blocks end up outside the toerail, they generally end up with the wide (aluminum) side of the block laying against the rubrail. Rick Brass Washington, NC From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Thursday, April 11, 2019 10:39 AM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Re: Stus-List Merriman snatch block question Thanks, Rick. I just visited Garhauer’s website. The comparable block would be the 70SN for $220, which is a good price. However, the cheeks are anodized aluminum, not rubber. The blocks on my boat normally attach to the toe rail, and it is not uncommon for a block to end up hanging outboard after use. I would expect aluminum blocks to beat up the gunwale gelcoat. Matt From: Rick Brass via CnC-List Sent: Thursday, April 11, 2019 10:24 AM To: cnc-list@cnc-list.com Cc: Rick Brass Subject: Re: Stus-List Merriman snatch block question Actually, Matthew, they are not that expensive. Here is a Garhauer snatchblock in the same size that I use on my 38 for $89 on eBay. https://www.ebay.com/itm/LARGE-Garhauer-opening-Snatch-Block/254192661569?hash=item3b2f103441:g:Hy4AAOSwF2FbqZHn I sold my old Merriman blocks at a yard sale and bought new Garhauer blocks years ago. Superior design with a rotating side plate that is retained by a spring loaded pin. Much stronger than what you have and closer to foolproof. Mine weren’t much over $100 from Garhauer when I bought them, but that was well over a decade ago. Rick Brass Washington, NC ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Has not happened on my 38. I have a pair of 70 series single blocks on swivel shackles permanently mounted to the toe rail aft of the winches that I use as turning blocks to get a good sheet lead into the winches (which really helps reduce the loads when moving the line adjustable genoa cars). And about 4 holes aft of the turning blocks are a pair of the 70 series snatch blocks for the spin sheets. I normally try to position the snatch blocks inboard with the cheeks on the top side to make line handling easier – but I’m old and forgetful so they often end up hanging on the outside of the toe rail when at the dock. In the spirit of full disclosure, my rubrail is a strip of HMWPE that was added to the hull in place of the original rubber rail, and it sticks out an inch or so further than the rubber rail that was typical of the 70s and 80s models. When the blocks end up outside the toerail, they generally end up with the wide (aluminum) side of the block laying against the rubrail. Rick Brass Washington, NC From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Thursday, April 11, 2019 10:39 AM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Re: Stus-List Merriman snatch block question Thanks, Rick. I just visited Garhauer’s website. The comparable block would be the 70SN for $220, which is a good price. However, the cheeks are anodized aluminum, not rubber. The blocks on my boat normally attach to the toe rail, and it is not uncommon for a block to end up hanging outboard after use. I would expect aluminum blocks to beat up the gunwale gelcoat. Matt From: Rick Brass via CnC-List <mailto:cnc-list@cnc-list.com> Sent: Thursday, April 11, 2019 10:24 AM To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com> Cc: Rick Brass <mailto:rickbr...@earthlink.net> Subject: Re: Stus-List Merriman snatch block question Actually, Matthew, they are not that expensive. Here is a Garhauer snatchblock in the same size that I use on my 38 for $89 on eBay. https://www.ebay.com/itm/LARGE-Garhauer-opening-Snatch-Block/254192661569?hash=item3b2f103441:g:Hy4AAOSwF2FbqZHn I sold my old Merriman blocks at a yard sale and bought new Garhauer blocks years ago. Superior design with a rotating side plate that is retained by a spring loaded pin. Much stronger than what you have and closer to foolproof. Mine weren’t much over $100 from Garhauer when I bought them, but that was well over a decade ago. Rick Brass Washington, NC _ ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
But then I’ll have to buy him a beer, or worse yet, two. From: Dennis C. via CnC-List Sent: Thursday, April 11, 2019 1:58 PM To: CnClist Cc: Dennis C. Subject: Re: Stus-List Merriman snatch block question If you want to repair the pin in a snatch block, go to mcmaster.com and look at "barrel nuts and screws". No idea what the load rating on them would be but perhaps they might work. Or, take up Bill Coleman's offer and advice.. Dennis C. Touche' 35-1 #83 Mandeville, LA ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Robbie: Thanks. That is the inelegant solution that I knew would work when I started this unfortunate thread. Given that no one has suggested a source for a replacement pin, I suspect that's where I'm headed. I appreciate everyone's input. Matt -Original Message- From: Robbie Epstein via CnC-List Sent: Thursday, April 11, 2019 1:04 PM To: cnc-list@cnc-list.com Cc: Robbie Epstein Subject: Re: Stus-List Merriman snatch block question Matthew, I have four of the large Merriman snatch blocks on my boat. Over the years, all the center shafts have failed at some point. The little screw that hold the holds the shaft in simply isn't up to the task. If you want to fix it for less than 5 bucks, get a 3/8" x 3 1/2" stainless bolt, which has 2 1/2' of solid unthreaded shank for the roller to use as a bearing surface, and cut off just enough of the threads with a hacksaw to accept a washer and locknut. If I recall, you have to drill out one of the cheek straps to 3/8", but the other strap already has that size hole. Its not as pretty as a the original, but it's not coming loose, and I'm guessing the snap shackle will fail long before the shaft and cheeks. Robbie Epstein Thorfinn C 40 TMDK ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
If you want to repair the pin in a snatch block, go to mcmaster.com and look at "barrel nuts and screws". No idea what the load rating on them would be but perhaps they might work. Or, take up Bill Coleman's offer and advice.. Dennis C. Touche' 35-1 #83 Mandeville, LA ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Let me preface with a good, "You do you". The Gaurhaure snatch blocks have a hole in their middle which allows for a bungee or simple line to be clipped to the lifeline. This keeps the block from falling to the deck or topsides when not in use. I even used lines such as these and saw them used on blocks that where not made by Gaurhaure pretty frequently. Josh Muckley S/V Sea Hawk 1989 C 37+ Solomons, MD On Thu, Apr 11, 2019, 10:41 AM Matthew L. Wolford via CnC-List < cnc-list@cnc-list.com> wrote: > Thanks, Rick. > > I just visited Garhauer’s website. The comparable block would be the 70SN > for $220, which is a good price. However, the cheeks are anodized > aluminum, not rubber. The blocks on my boat normally attach to the toe > rail, and it is not uncommon for a block to end up hanging outboard after > use. I would expect aluminum blocks to beat up the gunwale gelcoat. > > Matt > > *From:* Rick Brass via CnC-List > *Sent:* Thursday, April 11, 2019 10:24 AM > *To:* cnc-list@cnc-list.com > *Cc:* Rick Brass > *Subject:* Re: Stus-List Merriman snatch block question > > > Actually, Matthew, they are not that expensive. Here is a Garhauer > snatchblock in the same size that I use on my 38 for $89 on eBay. > > > > > https://www.ebay.com/itm/LARGE-Garhauer-opening-Snatch-Block/254192661569?hash=item3b2f103441:g:Hy4AAOSwF2FbqZHn > > > > I sold my old Merriman blocks at a yard sale and bought new Garhauer > blocks years ago. Superior design with a rotating side plate that is > retained by a spring loaded pin. Much stronger than what you have and > closer to foolproof. Mine weren’t much over $100 from Garhauer when I > bought them, but that was well over a decade ago. > > > > > > Rick Brass > > Washington, NC > > > > > -- > ___ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > ___ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Matthew, I have four of the large Merriman snatch blocks on my boat. Over the years, all the center shafts have failed at some point. The little screw that hold the holds the shaft in simply isn't up to the task. If you want to fix it for less than 5 bucks, get a 3/8" x 3 1/2" stainless bolt, which has 2 1/2' of solid unthreaded shank for the roller to use as a bearing surface, and cut off just enough of the threads with a hacksaw to accept a washer and locknut. If I recall, you have to drill out one of the cheek straps to 3/8", but the other strap already has that size hole. Its not as pretty as a the original, but it's not coming loose, and I'm guessing the snap shackle will fail long before the shaft and cheeks. Robbie Epstein Thorfinn C 40 TMDK ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Thanks, Rick. I just visited Garhauer’s website. The comparable block would be the 70SN for $220, which is a good price. However, the cheeks are anodized aluminum, not rubber. The blocks on my boat normally attach to the toe rail, and it is not uncommon for a block to end up hanging outboard after use. I would expect aluminum blocks to beat up the gunwale gelcoat. Matt From: Rick Brass via CnC-List Sent: Thursday, April 11, 2019 10:24 AM To: cnc-list@cnc-list.com Cc: Rick Brass Subject: Re: Stus-List Merriman snatch block question Actually, Matthew, they are not that expensive. Here is a Garhauer snatchblock in the same size that I use on my 38 for $89 on eBay. https://www.ebay.com/itm/LARGE-Garhauer-opening-Snatch-Block/254192661569?hash=item3b2f103441:g:Hy4AAOSwF2FbqZHn I sold my old Merriman blocks at a yard sale and bought new Garhauer blocks years ago. Superior design with a rotating side plate that is retained by a spring loaded pin. Much stronger than what you have and closer to foolproof. Mine weren’t much over $100 from Garhauer when I bought them, but that was well over a decade ago. Rick Brass Washington, NC ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Actually, Matthew, they are not that expensive. Here is a Garhauer snatchblock in the same size that I use on my 38 for $89 on eBay. https://www.ebay.com/itm/LARGE-Garhauer-opening-Snatch-Block/254192661569?hash=item3b2f103441:g:Hy4AAOSwF2FbqZHn I sold my old Merriman blocks at a yard sale and bought new Garhauer blocks years ago. Superior design with a rotating side plate that is retained by a spring loaded pin. Much stronger than what you have and closer to foolproof. Mine weren’t much over $100 from Garhauer when I bought them, but that was well over a decade ago. Rick Brass Washington, NC From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Chuck Gilchrest via CnC-List Sent: Tuesday, April 9, 2019 4:10 PM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Re: Stus-List Merriman snatch block question “Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List mailto:cnc-list-boun...@cnc-list.com> > On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com> Cc: Bill Coleman mailto:colt...@verizon.net> > Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com> Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Not a problem, Chuck. We’re all friends here (C smiles), but I figured you could use a little push-back. I’ve been sailing for about 50 years, and I have a fairly good sense when equipment should be retired. Nevertheless, as I said in a prior e-mail note, I plan to have the side straps looked at by someone knowledgeable about stainless. I appreciate the cautionary advice. Thanks for your follow-up note. From: Chuck Gilchrest via CnC-List Sent: Wednesday, April 10, 2019 11:00 AM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Re: Stus-List Merriman snatch block question Hi Matt, After re-reading my reply to your snatch block question, I apologize for the tone of my email. It was uncalled for and over the top. Having spent a fair bit of time on a professional level attending to service questions in a wide range of recreational sports, I guess I tend to have a knee jerk reaction when I suspect that someone is compromising safety in the name of frugality. Clearly this was not the case regarding your simple question of sourcing a replacement part for your blocks. Again, I apologize for the “lecture” and I’ll try to conduct future comments in a more professional and helpful manner. Sincerely, Chuck Gilchrest S/V Half Magic 1983 35 Landfall Pandanaram, MA Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Hi Matt, After re-reading my reply to your snatch block question, I apologize for the tone of my email. It was uncalled for and over the top. Having spent a fair bit of time on a professional level attending to service questions in a wide range of recreational sports, I guess I tend to have a knee jerk reaction when I suspect that someone is compromising safety in the name of frugality. Clearly this was not the case regarding your simple question of sourcing a replacement part for your blocks. Again, I apologize for the “lecture” and I’ll try to conduct future comments in a more professional and helpful manner. Sincerely, Chuck Gilchrest S/V Half Magic 1983 35 Landfall Pandanaram, MA Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
As we all know, size matters. From: Dennis C. via CnC-List Sent: Tuesday, April 09, 2019 6:55 PM To: cnc-list@cnc-list.com Cc: Dennis C. Subject: Re: Stus-List Merriman snatch block question Snatch blocks are usually available on eBay for $100 or less. Might not be the big ones but keep watching. Dennis C. Touché 35-1 #83 Mandeville,LA Sent from my iPhone On Apr 9, 2019, at 4:13 PM, Matthew L. Wolford via CnC-List wrote: With all due respect, the stainless straps on the side were only slightly bent and remain plenty strong. The pin, on the other hand, may be structurally compromised. This is why I asked for information (not a lecture). I’m not going to buy a $500 (or so) block when it can be repaired with a $15 (or so) pin. From: Chuck Gilchrest via CnC-List Sent: Tuesday, April 09, 2019 4:09 PM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Re: Stus-List Merriman snatch block question “Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com Cc: Bill Coleman Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray -- ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want
Re: Stus-List Merriman snatch block question
Snatch blocks are usually available on eBay for $100 or less. Might not be the big ones but keep watching. Dennis C. Touché 35-1 #83 Mandeville,LA Sent from my iPhone > On Apr 9, 2019, at 4:13 PM, Matthew L. Wolford via CnC-List > wrote: > > With all due respect, the stainless straps on the side were only slightly > bent and remain plenty strong. The pin, on the other hand, may be > structurally compromised. This is why I asked for information (not a > lecture). I’m not going to buy a $500 (or so) block when it can be repaired > with a $15 (or so) pin. > > From: Chuck Gilchrest via CnC-List > Sent: Tuesday, April 09, 2019 4:09 PM > To: cnc-list@cnc-list.com > Cc: Chuck Gilchrest > Subject: Re: Stus-List Merriman snatch block question > > “Fixing” bent snatch blocks??? Really?? Bending it back into shape? > Finding replacement pins for 30 year old blocks that are twisted and falling > apart? You need to consider metal fatigue and once stainless steel is bent > without applying heat, it is severely compromised. > I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once > a piece of critical hardware gives up and gets bent out of shape, it finds > its way into the scrap heap and gets replaced because I don’t depend on > damaged hardware to get me home safely.. Maybe because I love my children > and my wife and want to see them again. Just for the record, if the snatch > block lets go under load and kills someone or severely injures a crew member, > I hope you have enough liability insurance because it will not be something > you can pin on a company that has been out of business since 1989. > If you have a single piece of electronic gadgetry or cookware on your boat > that costs more than a snatch block and have limited financial resources, I > suggest you sell them and buy the new hardware that you need. And yes, I am > well aware that new snatch blocks are expensive..it’s for good reason! > Chuck Gilchrest > S/V Half Magic > 1983 35 Landfall > Padanaram, MA > From: CnC-List On Behalf Of Bill Coleman via > CnC-List > Sent: Tuesday, April 9, 2019 2:02 PM > To: cnc-list@cnc-list.com > Cc: Bill Coleman > Subject: Re: Stus-List Merriman snatch block question > > Lay it under my keel, I will take a look at it. I can probably beat it back > into shape. Might cost you a beer or two, tho. > I used to repair Merle’s Merrimans, and now of course I own them. > > Bill Coleman > C 39 Erie, PA > > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. > Wolford via CnC-List > Sent: Tuesday, April 09, 2019 1:15 PM > To: cnc-list@cnc-list.com > Cc: Matthew L. Wolford > Subject: Stus-List Merriman snatch block question > > Listers: > > I have an old Merriman snatch block in need of repair. It was under load > last season and not properly closed, which caused it to open and bend the > stainless straps (on the sides) and the pin holding it together. I believe I > can bend the stainless straps back more or less into alignment. However, the > pin is bent and in need of replacement. The pin used by Merriman for this > block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a > head on one end and internal threads on the other. It is held together by a > machine screw that screws into the threaded end. I suppose I could use a > stainless bolt, but that would not be very elegant. Any ideas? > > > > Thanks everyone for supporting this list with your contributions. Each and > every one is greatly appreciated. If you want to support the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray > > ___ > > Thanks everyone for supporting this list with your contributions. Each and > every one is greatly appreciated. If you want to support the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray > > ___ > > Thanks everyone for supporting this list with your contributions. Each and > every one is greatly appreciated. If you want to support the list - use > PayPal to send contribution -- https://www.paypal.me/stumurray > ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
It’s ok Chuck. Without getting into a long discussion, this is what I do for a living, for most of my working life, so I do know what I am doing. You don’t want to heat SS to form it, or any other reason, because then it is soft and rusts. SS is generally cold formed. You can bend a piece back and forth 180 degrees several times before it will break. We do that for weld tests. Don’t worry, I am not going to put Matt in jeopardy. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Chuck Gilchrest via CnC-List Sent: Tuesday, April 09, 2019 4:10 PM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Re: Stus-List Merriman snatch block question “Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com Cc: Bill Coleman Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Thanks, Josh. I suppose it depends on the size. I have about six of these massive snatch blocks on my boat, so moving one out of rotation for repair is not a big deal. The snap shackle, the closing mechanism, the sheave, the rubber cheeks, etc. are all in very good condition. I seriously doubt the stainless straps, even slightly bent, are the weak link. Chuck nevertheless raises a good point, and I will have them checked by someone who knows stainless in light of his comments. From: Josh Muckley via CnC-List Sent: Tuesday, April 09, 2019 5:38 PM To: C List Cc: Josh Muckley Subject: Re: Stus-List Merriman snatch block question FYI as I recall the Gaurhaure snach blocks are only about $100 and have a lifetime warranty. Josh Muckley S/V Sea Hawk 1989 C 37+ Solomons, MD On Tue, Apr 9, 2019, 5:15 PM Matthew L. Wolford via CnC-List wrote: With all due respect, the stainless straps on the side were only slightly bent and remain plenty strong. The pin, on the other hand, may be structurally compromised. This is why I asked for information (not a lecture). I’m not going to buy a $500 (or so) block when it can be repaired with a $15 (or so) pin. From: Chuck Gilchrest via CnC-List Sent: Tuesday, April 09, 2019 4:09 PM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Re: Stus-List Merriman snatch block question “Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com Cc: Bill Coleman Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray -- ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Contact Zephyerwerks, that guy can fix you up if it is fixable. Tom Power<http://aka.ms/weboutlook> Invictus C 30 MK1 Fredericton, NB From: CnC-List on behalf of Josh Muckley via CnC-List Sent: Tuesday, April 9, 2019 6:38 PM To: C List Cc: Josh Muckley Subject: Re: Stus-List Merriman snatch block question FYI as I recall the Gaurhaure snach blocks are only about $100 and have a lifetime warranty. Josh Muckley S/V Sea Hawk 1989 C 37+ Solomons, MD On Tue, Apr 9, 2019, 5:15 PM Matthew L. Wolford via CnC-List mailto:cnc-list@cnc-list.com>> wrote: With all due respect, the stainless straps on the side were only slightly bent and remain plenty strong. The pin, on the other hand, may be structurally compromised. This is why I asked for information (not a lecture). I’m not going to buy a $500 (or so) block when it can be repaired with a $15 (or so) pin. From: Chuck Gilchrest via CnC-List<mailto:cnc-list@cnc-list.com> Sent: Tuesday, April 09, 2019 4:09 PM To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> Cc: Chuck Gilchrest<mailto:csgilchr...@comcast.net> Subject: Re: Stus-List Merriman snatch block question “Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List mailto:cnc-list-boun...@cnc-list.com>> On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> Cc: Bill Coleman mailto:colt...@verizon.net>> Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PA[animated_favicon1] From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com> Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
FYI as I recall the Gaurhaure snach blocks are only about $100 and have a lifetime warranty. Josh Muckley S/V Sea Hawk 1989 C 37+ Solomons, MD On Tue, Apr 9, 2019, 5:15 PM Matthew L. Wolford via CnC-List < cnc-list@cnc-list.com> wrote: > With all due respect, the stainless straps on the side were only slightly > bent and remain plenty strong. The pin, on the other hand, may be > structurally compromised. This is why I asked for information (not a > lecture). I’m not going to buy a $500 (or so) block when it can be > repaired with a $15 (or so) pin. > > *From:* Chuck Gilchrest via CnC-List > *Sent:* Tuesday, April 09, 2019 4:09 PM > *To:* cnc-list@cnc-list.com > *Cc:* Chuck Gilchrest > *Subject:* Re: Stus-List Merriman snatch block question > > > “Fixing” bent snatch blocks??? Really?? Bending it back into shape? > Finding replacement pins for 30 year old blocks that are twisted and > falling apart? You need to consider metal fatigue and once stainless steel > is bent without applying heat, it is severely compromised. > > I’m as cheap as the next sailor (well maybe not the Canadian ones…) but > once a piece of critical hardware gives up and gets bent out of shape, it > finds its way into the scrap heap and gets replaced because I don’t depend > on damaged hardware to get me home safely.. Maybe because I love my > children and my wife and want to see them again. Just for the record, if > the snatch block lets go under load and kills someone or severely injures a > crew member, I hope you have enough liability insurance because it will not > be something you can pin on a company that has been out of business since > 1989. > > If you have a single piece of electronic gadgetry or cookware on your boat > that costs more than a snatch block and have limited financial resources, I > suggest you sell them and buy the new hardware that you need. And yes, I > am well aware that new snatch blocks are expensive..it’s for good reason! > > Chuck Gilchrest > > S/V Half Magic > > 1983 35 Landfall > > Padanaram, MA > > *From:* CnC-List *On Behalf Of *Bill > Coleman via CnC-List > *Sent:* Tuesday, April 9, 2019 2:02 PM > *To:* cnc-list@cnc-list.com > *Cc:* Bill Coleman > *Subject:* Re: Stus-List Merriman snatch block question > > > > Lay it under my keel, I will take a look at it. I can probably beat it > back into shape. Might cost you a beer or two, tho. > > I used to repair Merle’s Merrimans, and now of course I own them. > > > > Bill Coleman > > C 39 Erie, PA[image: animated_favicon1] > > > > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com > ] *On Behalf Of *Matthew L. Wolford via > CnC-List > *Sent:* Tuesday, April 09, 2019 1:15 PM > *To:* cnc-list@cnc-list.com > *Cc:* Matthew L. Wolford > *Subject:* Stus-List Merriman snatch block question > > > > Listers: > > > > I have an old Merriman snatch block in need of repair. It was under > load last season and not properly closed, which caused it to open and bend > the stainless straps (on the sides) and the pin holding it together. I > believe I can bend the stainless straps back more or less into alignment. > However, the pin is bent and in need of replacement. The pin used by > Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 > diameter) with a head on one end and internal threads on the other. It is > held together by a machine screw that screws into the threaded end. I > suppose I could use a stainless bolt, but that would not be very elegant. > Any ideas? > > > > > > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > -- > ___ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > ___ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
With all due respect, the stainless straps on the side were only slightly bent and remain plenty strong. The pin, on the other hand, may be structurally compromised. This is why I asked for information (not a lecture). I’m not going to buy a $500 (or so) block when it can be repaired with a $15 (or so) pin. From: Chuck Gilchrest via CnC-List Sent: Tuesday, April 09, 2019 4:09 PM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Re: Stus-List Merriman snatch block question “Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com Cc: Bill Coleman Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
“Fixing” bent snatch blocks??? Really?? Bending it back into shape? Finding replacement pins for 30 year old blocks that are twisted and falling apart? You need to consider metal fatigue and once stainless steel is bent without applying heat, it is severely compromised. I’m as cheap as the next sailor (well maybe not the Canadian ones…) but once a piece of critical hardware gives up and gets bent out of shape, it finds its way into the scrap heap and gets replaced because I don’t depend on damaged hardware to get me home safely.. Maybe because I love my children and my wife and want to see them again. Just for the record, if the snatch block lets go under load and kills someone or severely injures a crew member, I hope you have enough liability insurance because it will not be something you can pin on a company that has been out of business since 1989. If you have a single piece of electronic gadgetry or cookware on your boat that costs more than a snatch block and have limited financial resources, I suggest you sell them and buy the new hardware that you need. And yes, I am well aware that new snatch blocks are expensive..it’s for good reason! Chuck Gilchrest S/V Half Magic 1983 35 Landfall Padanaram, MA From: CnC-List On Behalf Of Bill Coleman via CnC-List Sent: Tuesday, April 9, 2019 2:02 PM To: cnc-list@cnc-list.com Cc: Bill Coleman Subject: Re: Stus-List Merriman snatch block question Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PA From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com> Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Re: Stus-List Merriman snatch block question
Lay it under my keel, I will take a look at it. I can probably beat it back into shape. Might cost you a beer or two, tho. I used to repair Merle’s Merrimans, and now of course I own them. Bill Coleman C 39 Erie, PAanimated_favicon1 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, April 09, 2019 1:15 PM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Stus-List Merriman snatch block question Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
Stus-List Merriman snatch block question
Listers: I have an old Merriman snatch block in need of repair. It was under load last season and not properly closed, which caused it to open and bend the stainless straps (on the sides) and the pin holding it together. I believe I can bend the stainless straps back more or less into alignment. However, the pin is bent and in need of replacement. The pin used by Merriman for this block is stainless, 2 1/2 inches long (I’m guessing 5/16 diameter) with a head on one end and internal threads on the other. It is held together by a machine screw that screws into the threaded end. I suppose I could use a stainless bolt, but that would not be very elegant. Any ideas? Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
