Wayne, the AM power level in this version only seems to produce a
carrier of 10 Watts when the requested power is 100W. While I don't
agree with the idea of calling the power anything other than the carrier
level, i.e. I would expect the power control to only go to about 30
Watts on AM, 10
I guess it's not quite off topic as I use a Perseus as an outboard
panoramic receiver with my K3... The ARRL review is quite interesting
and shows how far SDRs have come along.
The review is on the ARRL Members only page:
http://www.arrl.org/members-only/prodrev/
73 Dave, G4AON
GM all,
not that I am one of those AM guys but just checked my K3 which produces 45W
on 160 and 40W on 80.
Maybe some set up trouble, Dave?
73
Len
SM7BIC
Wayne, the AM power level in this version only seems to produce a
carrier of 10 Watts when the requested power is 100W. While I don't
agree
wa6riv wrote:
Hey Guys, I've sold my radio.I don't think so... Ted Wa6riv
I don't think so either.
For those who don't know, as a matter of principle, you should never
follow instructions to pay someone else part of an uncleared
international payment, from someone you don't know, as
Dave,
I agree with you - there is something odd going on.
Then, perhaps the power level setting should be renamed to PEP output
instead?
Let us see what Wayne finds out (in due time)
One more early morning on 160 with SSB contest going on it was possible to
work some NA westcoast on CW with an
I find power output varying also on SSB after 2.57 install.
Dropping power from 110w to 15w keying up and then increasing back to
100w I get about 50 w. Changing the band up or down and back again
yields full deflection. Any one else? SN 1749
Mike - N5WNG
I have the TxG VCE set to -1.5 db in order to avoid excessive peak SSB
power levels compared to CW levels... If I set it to 0 db or higher, I
get more carrier power on AM at the expense of excessive SSB power. I
guess it needs the power gain (Tx VCE) setting to be per mode, not SSB
and AM.
anybody work on xv432. need mine fixed. itbeyond my abilities.
ron
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Len
I checked the calibration at 5 and 50 Watts, the carrier power is close
to the power control setting at other power settings too. Earlier
firmware gives higher power, although still short of the expected 25 -
40 Watt carrier. I have gone back to f/w version 2.46, although that has
bounced mail
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Some observations on the new beta release of the firmware.
* The problem with excessive output power in DATA A has been greatly
reduced. I'm seeing nearer 6W on a pure tone when 5W is selected (pro rata
for other powers) and the audio level is adjusted for 4 bars.
* On AM with 10W selected my
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
As an addendum to my original post; Problem only occurs on 40 meters (dipole),
not able to reproduce on 20, 15 or 10 meters (yagi).
___
Elecraft mailing list
Post to:
I normally operate CW. I recently installed the CW rise time mod, the AGC
mod, the ALC mod for the PW-1, the KXV3 option. The firmware is at 2.38. I
tried to go to SSB on 20m last night and it will only find LSB now. Any
thoughts?? I sent a note to support but haven't heard anything yet. I
John Gaynard wrote:
I normally operate CW. I recently installed the CW rise time mod, the AGC
mod, the ALC mod for the PW-1, the KXV3 option. The firmware is at 2.38.
I
tried to go to SSB on 20m last night and it will only find LSB now. Any
thoughts?? I sent a note to support but
Hi Don,
Thanks for that, Putting aside the K2's low power on 160, which no doubt has
a component error value somewhere, the KPA 100 has been working at 111 Watts
for two years until I disturbed the PA last week to make way for the DSP
board. So something has happened to the KPA100. I only get a
Problem solved. Thanks for the support. Now I'm ready to create new
problems !
73 Allan 5Q8A
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
We measured very close to 25 W here, but I'll look into it.
tnx
Wayne
On Oct 25, 2008, at 12:51 AM, Dave G4AON wrote:
Wayne, the AM power level in this version only seems to produce a
carrier of 10 Watts when the requested power is 100W. While I don't
agree with the idea of calling the power
The Fall 2008 issue of 'QRP Quarterly' will be hitting mailboxes in
the next 2/3 weeks.
Further information (and an image of the contents page) can be found
at http://www.qrparci.org
For those not familiar with 'QRP Quarterly' a PDF of a typical back
issue is available for download.
Current
It measures very close here as well.
Even though the power calibrations had been done previously (this
was the factory built s/n 622), I did need to do the wattmeter and
power level calibrations again at both 5 and 50 watts before the
AM carrier power was within the 22-25 watt range across
Dave just pointed out that his TXG VCE menu entry (voice gain relative
to CW) was set to -1.5 dB. This menu entry should probably apply only
to SSB modes. I'll review this with our DSP engineer.
73,
Wayne
N6KR
Joe Subich, W4TV wrote:
It measures very close here as well.
Wayne, the AM
The capability to operate CW while in the SSB mode is wonderful. However,
it does not work when in the Split mode. This would be a really valuable
feature when operating on 40M in the SSB DX contest (at least for me)
because I have to re-tune the antenna every few kilohertz. Is there another
In going through the Transmitter Gain calibration procedure for 5 and 50 watts
the actual power output measured on an external wattmeter (W1 Powermaster)
drops off for the higher bands(4 and 40 watts on 10 meters) even though the
VFO B indicator remains at 5 watts and 50 watts. Am I missing
Dave just pointed out that his TXG VCE menu entry (voice gain
relative to CW) was set to -1.5 dB.
I just spent the time to check my other K3 ... its AM power is
also in the 22-25 watt range across HF (20 Watts on 6M). I have
TXG VCE set to +1 dB on s/n 622 (factory assembled) and +0.5 dB
I can't find 2.57 on the beta site (just 2.46). Was it removed, or am I
having a browser refresh problem?
- 73, John, W0JFR
wayne burdick wrote:
K3 beta-test firmware revision 2.57 (with DSP rev 1.94) is now
available.
This is a major release. Some recent changes have had only
Hello All,
As a quick note, it would also be nice IF the frequency display would display
the TX freq, rather than the RX only.
73, Scott WA6LIE
K3 #1993
From: Bud Semon N7CW
Sent: Saturday, October 25, 2008 9:52 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] [K3] Feature Request
The
Normal ... the internal wattmeter appears to have a slope.
On one K3, my power output is about 54W on 160, 50 W on 20,
47W on 10 and 42W on 6. The other radio shows 52W on 160,
50W on 20, 47W on 10 and 46W on 6.
73,
... Joe, W4TV
-Original Message-
From: [EMAIL
I'm afraid it's your browser John. I have Firefox set to clear it's
buffers, cookies, etc. when it closes and it's there on the Elecraft
site now at:
ftp://ftp.elecraft.com/K3/firmware/beta/
73 Dave, G4AON
I can't find 2.57 on the beta site (just 2.46). Was it removed, or am I
having a
We will see what difference another hour of daylight makes to the longer
skip QRM this week.
The frequency as always is plus or minus the QRM.
73 Dave, G4AON
K3/100, Acom 1000, dipole
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
Scott, Bud,
Perhaps I'm not understanding what you two are asking for ...
My VFO B display -does- display its frequency when the
radio's in SPLIT mode -and- I can transmit CW while in
-any- mode.
73! Ken Kopp - K0PP
- Original Message -
From: Scott Avery
To: Bud Semon N7CW ;
Just had my first CW QSO with K3 #2006, a K3/10 with KAT3 and 400 hz
filter! Assembly was entirely straight forward with no glitches at
all. I did put together another K3 for a friend in the spring, so I had
a little experience!
73,
Randy, KS4L
K2 #337
K3 #2006
PS If you noticed my first
And if you did forget to renew and need, want or desire the Fall 2008
issue, they
are in stock at the QRP-ARCI Back Issues department (In the cornor of my
basement!). http://www.k8dd.com/toystore/qqback.htm -- even though I have
not updated the page to show it, they really are in stock!
And it
Joe Subich, W4TV-3 wrote:
I don't know ... it seems to work properly here. If you elect
to not make it global, it may be necessary to provide separate
TXG settings for voice (SSB), AM and AFSK A/DATA A (DTA) ... or
at least SSB/Data and AM.
Perhaps I'm just being dim, but why is
I tried this yesterday, but I failed to give sufficient information to
describe my VFO B problems.
K3 1248
Firmware version 2.46
Software N1MM
P4 1.6 GB PC
microHam microkeyer
Working CQWWSSB mostly split on 40.
One problem and two areas of confusion.
1. When I attempt to us BSet, and
K-3 (kit) SN 1953 had it's first QSO today with very good reports recieved.
The SN is the same as my birth year, whats the chances of that.
73
Larry KA0PLW
K-1 #2530
K-2 #6491
K-3 #1953
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
20 meters is wall to wall with strong SSB signals this weekend. Take the
opportunity to connect an A/B switch to your best older transceiver vs. K3 and
you may find in some instances that the K3 is not optimally configured. My
settings were changed for SLOPE, THR, and SLOW. Also changed I/II
1. When I attempt to us BSet, and leave the K3 in that mode
for a period of time while pushing buttons to adjust VFO B,
I get a connection to radio lost message. Not every time but
often. I hit retry and it reconnects immediately. Not sure
if a certain button sequence triggers this, but
I note working CQWW SSB with K3 and N1MM Logger that on 40M whenever I click
on a N1MM spot, the K3 drops out of SPLIT. I will also alert N1mm
reflector.
Jim Denneny
K7EG Auburn WA 98092
___
Elecraft mailing list
Post to:
Ignore my message. If N1MM 40M spot contains both TX and RX freqs, K3 does
stay in SPLIT and QSY 's correctly. I was looking at spots containing only
DX freq when I saw the radio coming out of SPLIT. At any rate, be careful
when clicking on 40M spots during contest.
Jim Denneny
K7EG
I have a like new U.S. Interface Navigator with K3 cable for sale. I've never
used it and probably won't. Please contact me off the reflector if interested.
73,
Dave N8AG
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be
Good Evening,
Conditions turned good toward the end of the week and I had a couple of fine
skeds with a friend of mine. The weather seems to be getting slightly warmer
too. The forecast is for sunny days until at least Wednesday and Monday the
temperature is going to hit 70 degrees! Nice
Perhaps I'm just being dim, but why is TXG necessary at all?
Why can't you just turn the mic gain up until you have plenty
of drive, and then use the power control to set the output
power using the ALC?
Traditional ALC operates by overdriving the final amplifier.
It senses grid current
41 matches
Mail list logo