Thanks to all who sent me information and suggestions. It has been several
days and I just now got a chance to get to the radio (note 0115L) after a
week or so.
In going through all the suggestions and checking and changing some I found
that my RF gain was cranked down and all of a sudden I
I'm still slightly confused by the many reply options, double clicking,
typing in boxes etc. Is there a 'JT65 HF for dummies' anywhere? Despite
playing meteor scatter on vhf many years ago, where the QSO format is
pretty much identical to what I remember, I'm still a little confused by
what
This sounds like the dreaded 12v error although you don't mention seeing
that specific message on the display.
This happened to several I've heard about, including mine (S/N 1153) and,
in my case, was the corroded pin problem. Elecraft sent me a kit (free of
charge) but it not only involved
My K-3 (#5098) is a factory-built unit. I have tried 2 different stereo speaker
pairs but get audio from only the teathered one. Hard to believe both sets are
bad. Thoughts, please?
Bill K9HXO
__
Elecraft mailing list
Home:
Have you checked CONFIG/SPKRS ? If it's set to 1, change the setting to 2.
73,
Tim - N3XX
- Original Message -
From: Bill Miller k9...@yahoo.com
To: elecraft@mailman.qth.net
Sent: Saturday, May 05, 2012 7:01 AM
Subject: [Elecraft] K-3 speakers
My K-3 (#5098) is a factory-built unit.
I knew I should have stayed up all night making contacts.
At 10:30 PM EST 20m was open in MI, my problem was that I did not have
any energy it was a long week at work. :-(
~73
Don
KD8NNU
On Sat, May 5, 2012 at 12:52 AM, Wayne Burdick wrote:
In northern California I'm hearing dozens of very
Wow my post sent from my android was messed up.
What I tried to say was I have a Scorpion antenna and it has gone thru 2
winters in MI. I am just north of Ann Arbor.
Also I do not have a trailor hitch mount it is above my bumper on the
rear tailgate.
Hope this helps.
Don
~73
Don
KD8NNU
Good morning,
Well I just finished hanging my new G5RV yesterday and I have already had
some impressive results when comparing my long wire to the G5RV. After I
first connected the antenna to my K2 (7109 ) I thought something was wrong.
Then I figured out the I'm not hearing the noise that the
I have the Preditor as well, and have found that with 100 watts they say I'm
just as strong as I am at home (not sure what that really means :) ). I have
always believed that QRP or LP doesn't need small components with the attached
losses, but as huge as you can manage so as not to waste any
HI Roland,
When I spend some radio time this weekend I send them to you.
There are two sets of macros. One for HRD for the radio commands, then
a set in DM780 to use them.
They are not perfect macros, but they work for me. I was just happy
that I figured them out, I kinda programmed them
One of my friends had a screwdriver antenna mounted on an old motor mount.
It was bolted high side up in the bed of his truck, near the side-rear.
It got the entire antenna (including the feedpoint) above the sidewalls of
the truck bed. He insisted that mounting the antenna below there was
eating
Its just the opposite. You must use 'Reply All' to reply to the list.
'Reply' only goes to the original sender.
'Reply All' goes to the list and the original sender.
Eric
www.elecraft.com
_..._
On May 4, 2012, at 9:04 PM, Don Wilhelm w3...@embarqmail.com wrote:
Since your post appeared
Well said Erik. My credentials do not match yours, but I do have a BS in
Physics and made a living for 40 years as an Engineer. The theory may be bunk,
but that is what most said about Einstein when he presented the Theory of
Relativity. It sounds to me like a theory that is worth per-suing
On 5/5/2012 1:51 AM, Stephen Prior wrote:
I'm still slightly confused by the many reply options, double clicking,
typing in boxes etc. Is there a 'JT65 HF for dummies' anywhere?
Print the JT65-HF manual and study it.
73, Jim K9YC
__
Steve,
My K3 has done this several times and each time I had turned the power down
while running Ham Radio Delux and then turned off the program. The fix for me
is to start HRD again and use the slider to raise the power above 12 watts and
all is well again.
I am not sure this is what is
A starting point fro further reading might be:
http://physics.aps.org/story/v17/st15
John Ragle -- W1ZI
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
On 12-05-05 12:52 AM, Wayne Burdick wrote:
In northern California I'm hearing dozens of very strong EU stations
on 20 meter SSB. Wow.
Thanks for the heads up on this, Wayne. Although I didn't see the message
until this morning its amazing to think of 20m being open like that so late
at night.
It was side open to VK-land from SoCal a couple hours after Wayne's
notice. Again, over the pole.
EU is active on 15 and 17m this morning. Or was, three hours ago.
73,
matt W6NIA
On Sat, 05 May 2012 12:42:13 -0400, you wrote:
On 12-05-05 12:52 AM, Wayne Burdick wrote:
In northern
On 05/04/2012 10:03 PM, Erik Basilier wrote:
* The claim was not just that you can have two independent communications
(as possible by means of circular polarization), but more than two.
* The claim of multiple levels of angular momentum tells us that it is about
OAM and not SAM. The abstract
Has anyone else seen this message on their P3 ?
FATAL ERROR
In: ddc_set_coef()
span=0
Press any active key to escape
And, if you *have *seen it, how do you get out of it?
Power cycling (via the front panel switch) brings you back to this message.
There don't seem to be any other
I've had a couple of K1's but I am actually constructing my first one from a
kit. I need to decide whether to set the VFO range to 80 or 150Khz. I am
leaning toward the 150Khz because occasionally I like to go up to the slow
speed CW portion of 40 (7.110-7.125 Mhz) and also because it would be
Have you tried the Parameter Initialization process? It is described on page
28 of the manual.
-
Roger W5RDW
--
View this message in context:
http://elecraft.365791.n2.nabble.com/P3-Error-message-how-to-recover-tp7530882p7531026.html
Sent from the Elecraft mailing list archive at Nabble.com.
HI.
Am using my KX3 on digital. Noticed that in Digital USB when I dial
down the bandwidth to around 2.3 KHz the audio out goes away. Change the
setting up or down and the audio comes back. Also had bandwidth set to
600 hertz and tried to dial the center freq up to 2KHz but would not go
Hi all,
We've significantly improved the K3's DSP AGC based on feedback from
DXpedition users. In some cases, dozens of stations with nearly
identical amplitude may be packed together into just a few tens or
hundred of Hz of bandwidth. The AGC threshold can now be set much
higher,
Tom,
We'll try to duplicate your findings. I'll get back to you.
tnx
Wayne
N6KR
On May 5, 2012, at 2:16 PM, Tom Azlin N4ZPT wrote:
HI.
Am using my KX3 on digital. Noticed that in Digital USB when I dial
down the bandwidth to around 2.3 KHz the audio out goes away. Change
the
setting
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
thanks Wayne,
I can go take detailed notes and try to duplicate myself!
73, tom n4zpt
On 5/5/2012 5:40 PM, Wayne Burdick wrote:
Tom,
We'll try to duplicate your findings. I'll get back to you.
tnx
Wayne
N6KR
On May 5, 2012, at 2:16 PM, Tom Azlin N4ZPT wrote:
HI.
Am using my KX3 on
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Hi Joe,
Long ago when I got mine I chose to have my cake and eat it too. I built it
for 150 KHz but put a tiny dpdt switch on the back panel that allowed me to
put a resistor in series with the tuning pot at one end or the other
depending on switch position. The added resistor was the same
Maybe those fellows at 7O6T? ;)
73,
Scott, N9AA
On 5/5/12 5:28 PM, Wayne Burdick wrote:
Hi all,
We've significantly improved the K3's DSP AGC based on feedback from
DXpedition users. In some cases, dozens of stations with nearly
identical amplitude may be packed together into just a few
The weekly Elecraft SSB net will meet tomorrow (5/6/12) at 1800Z on 14.3035
MHz +/- QRM. I will be the net control station from Oregon. See you there.
73,
Phil, NS7P
__
Elecraft mailing list
Home:
Lost or confused perhaps Jussi, but not bored! Keep it up, maybe we will learn
something, maybe not!
Willis 'Cookie' Cooke
K5EWJ Trustee N5BPS, USS Cavalla, USS Stewart
From: Jussi Eloranta jmelora...@gmail.com
To: elecraft@mailman.qth.net
Sent: Saturday,
Just finished building the KX1 and the transmit testing is not going well. My
only bench tool is a DVM.
Power supply is a 13V battery. Ant is a 50 ohm dummy load. The receiver
seems to work fine. All DC voltages on RX are nominal.
On 40m TX, I get about 1.5W out. The signal is clean
I've had a couple of K1's but I am actually constructing my first one from a
kit. I need to decide whether to set the VFO range to 80 or 150Khz. I am
leaning toward the 150Khz because occasionally I like to go up to the slow
speed CW portion of 40 (7.110-7.125 Mhz) and also because it would
On 12-05-05 01:46 PM, Matt Zilmer wrote:
It was side open to VK-land from SoCal a couple hours after Wayne's
notice. Again, over the pole.
EU is active on 15 and 17m this morning. Or was, three hours ago.
I'll make a note to check the bands late this evening. I might fire up my K2
for the
Thanks for the input. I'm going the 150khz route. I installed the 18Mhz
crystal for 30 meters so I'm committed.
73
Joe
--
View this message in context:
http://elecraft.365791.n2.nabble.com/VFO-tuning-range-of-150Khz-tp7531023p7531168.html
Sent from the Elecraft mailing list archive at
Thanks for the replies.
Nothing truly 'fatal' about the error message I got; after I corrected the
source of the problem (I failed to tighten the DB9 retainer screws and
bumped the wires) it was quite simple to cycle the power and hold certain
buttons down to effect a reset.
I did lose my
I changed mine to the broader range so I could hit the slow spots on 40...
No problems - I would not go back.
73,
rayW0PFO
--
On 05/05/2012 03:48 PM, AF6NI wrote:
I've had a couple of K1's but I am actually constructing my first one from a
kit. I need to decide whether to set the VFO
The preproduction discount on our Rework Eliminator(TM) Option Bypass
Headers kit ends at 2359 EDT Monday May 7th. The current sale price
is $12.25, whereas after May 7th the retail price will be $20.75.
Both of these prices are lower than we previously advertised, thanks
to the significantly
39 matches
Mail list logo
