Thanks Jim
I think we ID'd it as SSTV near 14.230 but you are right as usual.
Time for me to get setup for digital and at least learn what they all
look/sound like. Sounds easy enough. I'll add it to the list.
Thanks to all who replied! Question answered; thread is dead, Fred!
On 6/7/2018 6:16 PM, Clay Autery wrote:
Can someone send me a screen cap off a P3 or something of the waveform
for FT8 (and any other digital mode).
Hi Clay,
It's worth downloading WSJT-X, installing it, RTFM, and then start
listening. It's excellent software, well written, well documented.
"I'm pretty sure I am seeing people running data WELL beyond the band plan into
the SSB section of several bands... 20m for almost certain."
Quite possibly the RF second harmonic of an in-band 40 m signal. It's unlikely
that anyone would hope to work a data mode QSO far away from the accepted
No P3 here but I can tell you that the SSTV people think they own 14.230.
Wes N7WS
On 6/7/2018 6:16 PM, Clay Autery wrote:
Can someone send me a screen cap off a P3 or something of the waveform for FT8
(and any other digital mode).
I'm pretty sure I am seeing people running data WELL beyond
Can someone send me a screen cap off a P3 or something of the waveform
for FT8 (and any other digital mode).
I'm pretty sure I am seeing people running data WELL beyond the band
plan into the SSB section of several bands... 20m for almost certain.
Thanks!
73,
__
Clay
Elecraft SP3 has been sold.
Bob
K8RL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
For sale Elecraft SP3 speaker. In very good condition. With Elecraft audio
cable and information sheet. Will ship in original box. Payment via Pay-Pal.
CONUS only. $140 shipped.
If interested, please contact me offline via email of BobK8RL at AOL.
Bob
K8RL
It has come to our attention (thanks to N7YK and N6TV) that the default value
of CONFIG:TX DLY, 8 ms, may actually be closer to 5 ms.
The associated T/R control firmware hasn’t changed in a long time, so hopefully
there aren’t many users affected (or we would have heard about it). The shorter
On Thu, Jun 7, 2018 at 6:52 PM Wayne Burdick wrote:
> Congrats, Dennis. When I worked him I was using 100 W to a 6 meter dipole
> made from two Hamsticks, erected last year when I finally discovered how
> cool 6 meters is.
>
After 45 years on HF CW, I'm intrigued and delighted by 6-meter SSB,
Congrats, Dennis. When I worked him I was using 100 W to a 6 meter dipole made
from two Hamsticks, erected last year when I finally discovered how cool 6
meters is.
I’m parked on 50.125, still hearing new signals come up every few minutes. It’s
almost like that scene in the movie “Contact”
Yeah I know...FT 8 has been going crazy all week! I've gotten several new
countries confirmed on LOTW.
73, Glenn wb5tuf
Original message From: Wayne Burdick Date:
6/7/18 17:25 (GMT-06:00) To: Elecraft Reflector
Cc: k...@yahoogroups.com Subject: [Elecraft] Nice 6 m opening
Thanks Wayne. My farthest contact on 6m, also with W5ZF. KAT500 worked
FB on a 130' doublet.
73, Dennis NJ6G
On 6/7/2018 15:25, Wayne Burdick wrote:
...Including SSB activity on 50.125...just had a cross-mode contact with W5ZF.
Lots of new beacons heard.
73,
Wayne
N6KR
Yup
A little bit of common mode
Russ KD4JO
Sent from my T-Mobile 4G LTE Device
Original message
From: Clay Autery
Date: 6/7/18 5:16 PM (GMT-05:00)
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] [K3] Heil 600 ohm balanced mic (PR40) connecting to rear
And if for some
...Including SSB activity on 50.125...just had a cross-mode contact with W5ZF.
Lots of new beacons heard.
73,
Wayne
N6KR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
The KPA500-F/KAT500-F combo has been sold.
Bob
K8RL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
And if for some reason you have a TRS available and not TS
connector just wire the ring and shield to Pins 1 and 3, and still
pin 2 to tip.
__
Clay Autery, KY5G
(318) 518-1389
On 06/07/18 13:59, Bob McGraw K4TAX wrote:
If you wish to make your own cable using a XLR
On 6/7/2018 9:06 AM, Michael Blake wrote:
You can buy the correct 3 pin XLR to 1/8” TS Male cable at your local Guitar
Center or similar place for less that $20….
Or you can make one with two connectors, some cable, and a soldering iron.
Wire pins 1 and 3 together and to the shield of the
If you wish to make your own cable using a XLR connector and a 1/8"
Tip-Sleeve connector, XLR pin #2 connect to Tip, XLR pin #3 and pin #1
to the Sleeve. In the XLR world, pin #1 is ground/shield, pin #2 is
hot (+ve) and pin #3 is cold (-ve) Thus for unbalanced use, pin #1 and
pin #3 must
For sale KPA500-F(SN 3481) and KAT500-F (SN 2531) purchased new as a combo in
February. Both tested good and are in excellentcondition, but have decided to
not keep them. Includes cables, slightly marked Cady (KE7X) book, marked
manuals, and ablack dust cover (no logo or lettering) for the
Mike, I connect my EV-RE50ND to the rear 1/8” connector on my K3s without
issue. You need an XLR to TS 1/8” male cable or adapter. The mic does not
care if it is balanced or unbalanced but if you use an XLR to TRS adapter the
ring will be floating free and will cause a problem.
You can buy
I would like to connect my 600 ohm balanced mic PR 77D to the K3s rear mic
connection. The mic connector is XLR 3-pin. I cannot figure out if the K3
rear connection can accept a balance mic. The adapters I have tried produce
hum and lead me to believe they force it to unbalance.
Any help
Elecraft KX3Transceiver SN 2151 with the followingaccessories; KX3-PCKT
Accessory cable set, KXAT3 Internal 20-w AutomaticAntenna Tuner, KXBC3 Internal
NiMH Charger with Real-Time Clock, KXFL3Dual-Passband Roofing Filter, KXPD3
Keyer Paddle, MH3 Hand Microphone, BNC-RABNC Rt, Angle M-F,
22 matches
Mail list logo
