"the transceiver still calls for the short burst of RF prior to transmitting at
full power."
Not sure I understand this. If you implement it correctly no RF TX is
required. I see Dick suggested you contact me. I'll be happy to share info on
my controller design. No RF TX required for my
*
I have an ICOM7300 with the KAT500 and KPA500. It is an outstanding
station and it is a pleasure to operate.
I would however, like to improve the operation by incorporating band
switching and frequency tracking. We built an Arduino based converter to
convert the ICOM CI-V serial data to
You can put (either) the KPA or the K3 on the KAT500, it can take the
weight. When I used that combo, the amp sat on the tuner, no issues.
However, it's in your better interest to allow nothing atop the K3 AND
the KPA to optimize cooling.
If you MUST stack them, shim (along the side edges)
Not just the levels but the right input source on the K3?
73,
Rick NK7I
On 12/11/2020 12:28 PM, Don Wilhelm wrote:
Joe,
Do you have the audio levels set right for transmit?
Go to my webpage www.w3fpr.com and look at the last article in the
left column.
73,
Don W3FPR
On 12/11/2020 3:10
Harlan -
You mean Top to Bottom ... right? KPA on top?
73
Lyn, W0LEN
PS - I prefer a small shelf unit to make removal easier.
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jim Rhodes
Sent: Friday, December 11, 2020
Personally (and this varies with every setup) I usually run with the sound
card output level about 1/3 of the way, the level in WSJT-X about 1/3 of
the way up then adjust the mic (line-in) to get the 4 bars plus a flicker
level on the ALC meter. You do not want any of the levels to be too near
That is how I would do it. KPA55 needs the most cooling. You will end up
with a maze of wires and cables behind the stack though.
On Fri, Dec 11, 2020, 13:18 Harlan Sherriff via Elecraft <
elecraft@mailman.qth.net> wrote:
> Rearranging the shack. This may have been answered before but I can’t
Joe,
Do you have the audio levels set right for transmit?
Go to my webpage www.w3fpr.com and look at the last article in the left
column.
73,
Don W3FPR
On 12/11/2020 3:10 PM, Joe K2UF wrote:
I am trying to get FT8 running on my K3 using Rig blaster advantage.
Everything works except no
I am running with no interface, an d all works well here. You might
consider re-configuring to not use the Rigblaster.
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist, RFI
ARRL Asst. Director, NW Division, Technical Resources
On 12/11/20
Vox on Joe?
On 11/12/2020 12:10 p.m., Joe K2UF wrote:
I am trying to get FT8 running on my K3 using Rig blaster advantage.
Everything works except no transmit RF output.
Enable TX puts K3 into transmit but no RFoutput. Have tried adjusting RBA
xmit level and K3 mic output. No joy.
Rearranging the shack. This may have been answered before but I can’t find it.
Is it okay to stack the three units bottom to top:
KPA
KAT
K3
73’
Harlan
K4HES
Sent from my iPhone
__
Elecraft mailing list
Home:
I am trying to get FT8 running on my K3 using Rig blaster advantage.
Everything works except no transmit RF output.
Enable TX puts K3 into transmit but no RFoutput. Have tried adjusting RBA
xmit level and K3 mic output. No joy.
.Anyone able to share their PTT settings.
Thanks,
Joe K2UF
I opted for a Rigol DS1202Z-E.
Thanks for all the great input. These scopes are all amazing for the price and
have way more capability than I'll use.
Lou W7HV
On Wednesday, December 9, 2020, 3:38:33 PM MST, Rich NE1EE
wrote:
On 2020-12-09 14:04:-0500, Kevin Cozens wrote:
I
Check your RX ANT settings to be sure that you haven't inadvertently selected
a non-existent RX antenna.
(see bottom paragraph of page 70 in the K3s User Manual).
Mike, K8CN
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
If looking for a distraction from our COVID driven altered lifestyle, check out
my snaps and narrative of a SOTA hike last August.
https://nomadic.blog/2020/12/11/are-your-laurels-in-the-bloody-mountains/
Paul Gacek
W6PNG/M0SNA
www.nomadic.blog
Hi - Has anyone experienced a K3s not receiving on 80m?
All other bands appear OK.
Any insight - What might I be missing. Have not heard back from Elecraft
support.
Thanks
73 wayne N1WP
__
Elecraft mailing list
Home:
wks9...@charter.net
On Fri, Dec 11, 2020 at 10:02 Jonathan Archer wrote:
> I’m interested in your sale please contact
>
> On Fri, Nov 27, 2020 at 04:12 wrote:
>
>> Send Elecraft mailing list submissions to
>> elecraft@mailman.qth.net
>>
>> To subscribe or unsubscribe via the World Wide
On Fri, Nov 27, 2020 at 04:12 wrote:
> Send Elecraft mailing list submissions to
> elecraft@mailman.qth.net
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://mailman.qth.net/mailman/listinfo/elecraft
> or, via email, send a message with subject or body 'help'
18 matches
Mail list logo
