Re: [Elecraft] No Tx Audio

Joe & Bob - thank you very much, you nailed it. The K3 Monitor, when the K3 was in a digital mode, was at 0. Now  have it turned up to 6 and my problem is solved in all the digital modes I listed. Tnx fer quick response. 73 Paul w2eck

[Elecraft] No Tx Audio

Problem: Not hearing any audio during transmit in digital modes.I have a K3, Win 10 PC, with microHam DKII interface. When transmitting inRTTY, PSK31 or FT-8 I am not hearing any Tx audio, which I had been previously.  I first noticed this in RTTY when not hearingany diddles. But when using

[Elecraft] KX3 & Signalink Not Transmitting

Thanks to AI5II's suggestions got the Tx problem fixed. Changed the Rig to KX3 and PTT to CAT. So the Signalink Tigertronics guidance was not accurate, at least for me. Also had Win4K3 running and it was using the KX3 comport. So closed that program and now the KX3 is receiving and transmitting

[Elecraft] KX3 & Signalink Not Transmitting

I had to send my K3 infor repairs, so I will be using my KX-3 as my main radio for the next fewweeks. But I haven’t got it working with Digital modes yet in particular FT-8.    PC is a Win 10 and amusing a Signalink USB. I am able to receive fine in WSJT-X but not transmit.  Settings in

Re: [Elecraft] Astron VS-35M Power Supply V-

Jim- thanks much for the quick reply. Very helpful 73Paulkc2nyu __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

[Elecraft] Astron VS-35M Powwer Supply V-

I have been working on bonding my station equipment and have come the issue of bonding/RFI fixes to the VS-35M. I have read that it is suggested to scrape the paint around the green wire from the ac round plug attachment point to the case. But there is also a small black wire that bonds the V-

[Elecraft] A question on the P3 or actually the Tx Mon (K3)

Alan - is there any documentation available on the procedure for calibrating the Tx Monitor? 73Paul __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post:

[Elecraft] A question on the P3 or actually the Tx Mon (K3)

A related question on this subject concerning the Tx Monitor. In terms of Power & SWR readings, can the Transmit Monitor be calibrated ? Or have other users found no need to adjust readings right out of the box? Reviewing the P3 manual on pages 34-35 there isn't much said about this subject.

Re: [Elecraft] K-Pod Macro Question

ilto:elecraft-boun...@mailman.qth.net] On Behalf Of paul ecker via Elecraft Sent: Wednesday, October 5, 2016 8:36 AM To: elecraft@mailman.qth.net Subject: [Elecraft] K-Pod Macro Question In my K3 I have SPKR+PH set to YES, and sometime ago Iassigned a macro to PF2 that allows me to switch  the speaker eith

[Elecraft] K-Pod Macro Question

In my K3 I have SPKR+PH set to YES, and sometime ago Iassigned a macro to PF2 that allows me to switch  the speaker either on or off, even though Ihave headphones plugged in. But I'll be darn if I can remember or figure outnow, what the macro cmd would be so I can assign the same action to a

[Elecraft] K3S and HRD

Save your self a lot of trouble and change over to Win4K3 Suite. It is specifically designed for Elecraft products and the customer support leaves HRD in its rearview mirror. Check out the website.  73Paulkc2nyu Win4K3 Suite Software for the Elecraft K3 K3S and KX2 | | | | ||

Re: [Elecraft] K3: K-pod uses

Don - thanks for the info, helpful. 73Paul From: Don Wilhelm To: KC2NYU ; elecraft@mailman.qth.net Sent: Wednesday, July 13, 2016 11:18 AM Subject: Re: [Elecraft] K3: K-pod uses Paul, If you are completely comfortable with mouse tuning

[Elecraft] FSQCALL PTT (K3)

Joe- understand and thanks very much for the help.  Paul kc2nyu >> You will need to make sure no other program is currently using theCAT Port. >>Windows does not allow sharing of ports. Any program using a port must close (release) the port before another program can open (begin using it).

[Elecraft] FSQCALL PTT (K3)

the K3. At Program start, the PTT/CAT settings >>window comes up every time. If I choose PTT or CAT, it says comport already in >>use. So I cancel the settings window and use Vox. It works but not sure it is >>ideal. >>73 Paul>>kc2nyu On 6/28/2016 5:20 PM, paul ecker vi

[Elecraft] FSQCALL (K3)

Joe- replies embedded at dashes in italics What softwareare you using for FSQCALL?  I see atleast three programs that supportFSQ mode. -- usingFSQCALL v0.36 by ZL2APF What are thePTT settings in your software? - settings inPTT/Cat settings  are com14 --00,kenwood(oldermodels) -- Use PTTIs

[Elecraft] FSQCALL PTT Issue (K3)

Wondering if anyone is group is having success running FSQCALL with their K3. When I open the program, the K3 red Tx light immediately comes on and thus no audio is received. It seems like there is an issue in the PTT/CAT settings,(where I have selected the comport, radio type-00,older kenwood

Re: [Elecraft] Rerouting the KRX3 AUX Input from the Rear BNC to the KAT3

Interesting thread and one that I have a question on. I have three antennas coming in to the KAT3 and one jumper running from the KAT3 XMTR connector to my K3 Ant1. When I installed the KRX3, I made the choice to have the main and sub receiver share the antenna output of the KAT3. Since I had

[Elecraft] Starving" Fldigi for audio Rx

In response to my question on the Win- Fldigi Reflector that I asked regarding waterfall adjustments and the fact that I was seeing no signals on the Fldigi Scope, Dave W1HKD  responded,--- If you need those controls set to the maximum range and lowest absolute signal (or close to it) then you

[Elecraft] Starving Fldigi for audio Rx - K3

After reading received comments, I verified my settings, they are:In Fldigi- Settings- Audio- Capture- Line(6-microHAM CODEC) ;                                          Playback - Headset Earphone (6-microHAM CODEC) In the K3 - config- LIN OUT - nor 010; the microHAM DK II RX MAIN Pot is  at

[Elecraft] P3 CW Decoding doesn't match K3

While copying the ARRL 20M CW broadcast I noticed that the decoding on the K3 is quite accurate as long as the signal does not fade. But while the K3 is decoding very well, the data display of cw text on the bottom of the SVGA display  is no whereas close to the accuracy of the K3. Anyone else

Re: [Elecraft] P3 CW Decoding doesn't match K3

ve perfect copy on the P3SVGA monitor. 73, Ron AC7AC -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of paul ecker via Elecraft Sent: Friday, November 13, 2015 1:40 PM To: elecraft@mailman.qth.net Subject: [Elecraft] P3 CW Decoding doesn't match K3 W

[Elecraft] Fw: K3-RTTY-No Diddles

Don- I was able to measure the voltage between pin 1 pin 5 at the K3 ACC plug. It measured 4.95v -- I then removed everything from the ACC plug and plugged in the test DB15 plug with only wires on pin 1 5. Put the K3 in FSK-D submode, and tapped XMIT, I got a steady tone. I then shorted pin

[Elecraft] K3-RTTY-No Diddles

Ihave a K3 (entire K-Line). Win 7 PC 3.5ghz processor 16gb ram; MicroHam DKII Interface. Withthis setup I am able to successfully do PSK31 using HRD-DM780, WSJT-X andJT65HF, WSPR and run N1MM+ successfully in SSB and CW - both RX TX. Myproblem is with MMTTY both running byitself or as the

[Elecraft] K3-RTTY-No Diddles

Don - The Output of DK II is connected to the K3 ACC port using a DB15-EL-K3 cable supplied by microHam with the DK II. 73 Paulkc2nyu --Paul, Details on how you are connecting the DKII FSK output to the K3 please. A quick perusal of the DKII information indicates

[Elecraft] K3 Audio Reports

I tried running the Audio test described below with my K3 DVR and for some reason my own audio is not being recorded. The DVR works fine recording  and playing audio off the air. But when I attempt to record my own audio as described below, when I play it back to you can hear audio go to zero

[Elecraft] K3 Goes to TX on Turn ON

Have a problem that just cropped up last night. When I turn on my K3, the red TX light immediately goes on. After connecting and disconnecting all external connections to K3, I determined the culprit was the RS-232 cable to the P3. If I disconnect the cable problem goes away, red TX light goes

[Elecraft] K3 Goes to TX on Turn ON

I changed K3 PTT-Key to OFF-OFF, that seems to have solved TX on turn on problem. But now - not sure if related- K3 will not talk to PC serial port. I have two 2 port serial cards installed my Win 7 64 bit PC. I tried cable from K3 in all four and can't get it to connect. Also cannot get KPA

[Elecraft] K3/MMTTY/Signalink Problem

Thanks for all the inputs on my question.I have made some progress. I changed the K3 mode from AFSK to Data A, and in MMTTY haveRev selected. I am now upon TX getting power out, movement on the ALC meter (4 bars with 5th flickering, mic line set at 31) and hearing Diddles. So MMTTY is working

Re: [Elecraft] K3/MMTTY/Signalink Problem

I have the Pitch in AFSK set the same as the mark in MMTTY. I am using Signalink USB external sound card and the K3 and MMTTY. But the question remains, if I set K3 mode to AFSK I get no power out or no Diddles. With Data A I do get power out and Diddles. Why is that ??  Even though using Data

[Elecraft] K3/Signalink/MMTTY Problem

I have Net on and AFC off in MMTTY. I continue to go through MMTTY help file and K3 manual but have yet to find a solution. Still would like to find another K3 owner who is using a Signalink as an interface with MMTTY. That would be quite helpful. a

[Elecraft] K3/MMTTY/Signalink Problem

I am having problems getting MMTTY to transmitproperly using K3 with a Signalink USB interface. Currently, when I go to TX in MMTTY, I get red TXlight on Signalink, a red TX light on K3, I hear diddles coming out of theSignalink rear monitor jack, and   I seemovement on Vu meter in Windows