Hi Gary, group, Elecraft support,
I think I have found a strong correlation between CW in SSB not
working and the QRQ setting. Here follows:
To make CW in SSB work: set CONFIG:QRQ to OFF, power-cycle the K3.
To break CW in SSB: set CONFIG:QRQ to ON, power-cycle the K3.
73,
Frank PA4N
At
Same here, it works fine for me with latest beta. I never use VOX on ssb.
it's a very useful feature.
73 Stephen G4SJP
On 3 February 2012 00:12, Sam Morgan k5oai@gmail.com wrote:
when I have CW WGHT [1] set to SSB +CW
the K3 transmits cw when in mode ssb
no matter whither I have vox
me a new one during a SSB operation.
Does it make me a lid? Looking to be enlighten.
73,
Terry, W0FM
-Original Message-
From: Stephen Prior [mailto:eastbrantw...@gmail.com]
Sent: Friday, February 03, 2012 3:02 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode
' Cooke
K5EWJ Trustee N5BPS, USS Cavalla, USS Stewart
From: Terry Schieler terry.schie...@wirelessusa.com
To: elecraft@mailman.qth.net
Sent: Friday, February 3, 2012 1:01 PM
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
I have read this thread with great
You can use this to check into nets where US (or at least lower 48)
folks do not have voice privileges. There are some Canadian and Alaskan
nets which run SSB but welcome folks running CW from the lower 48.
Kevin. KD5ONS
On 2/3/2012 11:41 AM, WILLIS COOKE wrote:
Terry, my understanding
...@gmail.com]
Sent: Friday, February 03, 2012 3:02 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
Same here, it works fine for me with latest beta. I never use VOX on ssb.
it's a very useful feature.
73 Stephen G4SJP
Of WILLIS COOKE
Sent: Friday, February 03, 2012 12:42 PM
To: Terry Schieler; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
Terry, my understanding is that this feature is used almost exclusively
by DXers on the VHF bands. I have never seen it used on the HF bands
: [Elecraft] K3: CW in SSB mode broken?
Terry, my understanding is that this feature is used almost exclusively
by DXers on the VHF bands. I have never seen it used on the HF bands
even though it would be legal. It allows you to keep the receiver on
SSB while using the transmitter on CW. I
Schieler
terry.schie...@wirelessusa.com; elecraft@mailman.qth.net
Sent: Friday, February 3, 2012 4:06 PM
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
In that scenario, what's wrong with CW mode and setting the filter suitably
wide?
73, Thomas M0TRN
On 3 February 2012 22:05, Cady, Fred
terry.schie...@wirelessusa.com; elecraft@mailman.qth.net
Sent: Friday, February 3, 2012 4:05 PM
Subject: RE: [Elecraft] K3: CW in SSB mode broken?
Here is another scenario:
You are operating at the scene of a disaster using a low antenna and low power
while passing health-and-welfare traffic. You can hear
: Thomas Horsten tho...@horsten.com
To: Cady, Fred fc...@ece.montana.edu
Cc: WILLIS COOKE wrco...@yahoo.com; Terry Schieler
terry.schie...@wirelessusa.com; elecraft@mailman.qth.net
Sent: Friday, February 3, 2012 4:06 PM
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
In that scenario, what's
COOKE wrco...@yahoo.com
Cc: Thomas Horsten tho...@horsten.com; Cady, Fred fc...@ece.montana.edu;
elecraft@mailman.qth.net elecraft@mailman.qth.net; Terry Schieler
terry.schie...@wirelessusa.com
Sent: Friday, February 3, 2012 4:41 PM
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
On Fri
@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
I don't remember the menu option Fred, but it is just an option that you
turn on or off then all you need to do is key the transmitter when you
are in SSB. The only problem that I have is occasionally bumping the
paddles
I use CW in SSB mode on VHF contest regularly. It is a matter of
convenience. Station is calling in SSB, and I hear them, but need to bust
through the traffic going on at the far end, especially when I am a low
power rover out in the boonies.
I try first in SSB but soon I realize I am not
Lance and Don,
That is exactly how I have my K3 configured with an external
sequencer. In voice the PTT keys the K3 and I take KEYOUT to key the
sequencer. The final stage of the sequencer defeats the INHIBIT line
to the K3 enabling transmit. I do not run QSK on VHF so I manually
switch
I can't do 6M, but I use this feature often on the other bands. I don't use
VOX. I just hooked up the antenna and verified it. Using f/w 04.36
Dick, n0ce
One thing that disappointed me is that this very useful cross-mode feature (at
least
on 6m, where I do most of my operating), is
CW works in SSB mode only if Vox is on because you have not used the
PTT. This is exactly parallel to the procedure for CW, where you can
only send without PTT by turning Vox on.
Jan, KX2A
__
Elecraft mailing list
Home:
On Thu, Feb 2, 2012 at 3:38 PM, Jan Ditzian ditz...@windstream.net wrote:
CW works in SSB mode only if Vox is on because you have not used the
PTT. This is exactly parallel to the procedure for CW, where you can
only send without PTT by turning Vox on.
Nice theory, but it's not true (as far
when I have CW WGHT [1] set to SSB +CW
the K3 transmits cw when in mode ssb
no matter whither I have vox implemented or not
Firmware MCU 4.42 FPF 1.14 DSP 2.73
K3 util 1.4.10.11
K3 #4123
--
GB 73
K5OAI
Sam Morgan
On 2/2/2012 5:38 PM, Jan Ditzian wrote:
CW works in SSB mode only if Vox is on
I, too, recall this being broken some time back. And I also seem to remember
a promise to fix it. It would be quite helpful if it worked while in Split
for users such as myself that need to tune on a Split frequency for autotune
amps, tuners, etc.
Jerry N8BM
CW in SSB mode generally works
Hi group,
Some time ago, I used to be able to send CW while in SSB mode, but it
no longer works. I do have the SSB +CW option on (press 1 in
CONFIG:CW WGHT), and do have the CW sidetone when I key my paddle
while in SSB mode. But the K3 does not produce RF output. I'm using
firmware version
Hi Greg,
Yes, I have tried with VOX on. I see the red TX led on the K3 come
on, I see the leftmost bar in the RF output lcd bar come on. But no
RF output on my external SWR meter. That SWR *does* show RF output
when I speak into the mike, or when I switch to CW mode and make CW.
At 18:35
Even with VOX on, if you assert PTT along with CW keying, you will be
transmitting in SSB mode, not CW. Try disconnecting PTT and see if it
works...
~iain / N6ML
On Tue, Jan 31, 2012 at 10:01 AM, Frank R. Oppedijk fr...@qrd.nl wrote:
Hi Greg,
Yes, I have tried with VOX on. I see the red
Hi,
I'm not asserting PTT. If I did, I'd indeed be transmitting SSB, as
can be clearly heard on the monitor. So it must be yet something else...
At 19:13 31/01/2012, you wrote:
Even with VOX on, if you assert PTT along with CW keying, you will be
transmitting in SSB mode, not CW. Try
Hi Ken,
No, I think not. If I assert PTT and speak, I see plenty output
power. If I switch to CW mode and make CW, I see plenty output power.
So it cannot be that...
At 19:44 31/01/2012, Rose wrote:
Is the PWR set to 0?
73!
Ken - K0PP
mailto:elecraftcov...@gmail.comelecraftcov...@gmail.com
-
From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
boun...@mailman.qth.net] On Behalf Of Frank R. Oppedijk
Sent: Wednesday, 1 February 2012 7:48 a.m.
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
Hi Ken,
No, I think not. If I assert PTT
(the best kind!).
73
Gary ZL2iFB
-Original Message-
From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
boun...@mailman.qth.net] On Behalf Of Frank R. Oppedijk
Sent: Wednesday, 1 February 2012 7:48 a.m.
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB
CW in SSB mode works fine here.
Firmware versions:
MCU 4.47
FPF 1.15
DSP1 2.73
73,
Bruce, N1RX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
It works OK here w/4.39
73!
Ken Kopp - K0PP
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
]On Behalf Of Frank R. Oppedijk
Sent: Tuesday, January 31, 2012 4:04 PM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
Gary and others,
Yes, I momentarily saw it working okay on 6 meters when I did a brief
transmission on that band.
Unfortunately, as I don't have
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
CW in SSB mode works fine here.
Firmware versions:
MCU 4.47
FPF 1.15
DSP1 2.73
73,
Bruce, N1RX
__
Elecraft mailing list
Home: http
I must be missing something. Can someone explain why you would want to send
CW in SSB mode?
I did go and find the setting, changed it to SSB +CW, and it works fine
here, using firmware 4.36.
Tnx 73,
Tim - N3XX
On 1/31/12, Frank R. Oppedijk mailto:fr...@qrd.nlfr...@qrd.nl
wrote:
Hi group,
For one thing, it's quite useful on 6m, where DX will often switch
back and forth between CW and SSB on the same frequency).
73,
~iain / N6ML
On Tue, Jan 31, 2012 at 2:11 PM, N3XX n...@charter.net wrote:
I must be missing something. Can someone explain why you would want to send
CW in
: [Elecraft] K3: CW in SSB mode broken?
For one thing, it's quite useful on 6m, where DX will often switch back
and
forth between CW and SSB on the same frequency).
73,
~iain / N6ML
On Tue, Jan 31, 2012 at 2:11 PM, N3XX n...@charter.net wrote:
I must be missing something. Can someone
For those who say it is broken - are you by any chance in split mode? It does
not work in split(at least for me). Otherwise, works fine.
Bob W6VY
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
: Tuesday, January 31, 2012 5:11 PM
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
On 1/31/12, Frank R. Oppedijk mailto:fr...@qrd.nlfr...@qrd.nl
wrote:
Hi group,
Some time ago, I used to be able to send CW while in SSB mode,
but it no longer works. I do have the SSB +CW option on (press 1
Message -
From: iain macdonnell - N6ML a...@dseven.org
To: N3XX n...@charter.net
Cc: Elecraft@mailman.qth.net
Sent: Tuesday, January 31, 2012 5:16 PM
Subject: Re: [Elecraft] K3: CW in SSB mode broken?
For one thing, it's quite useful on 6m, where DX will often switch
back and forth between
CW in SSB mode generally works fine here but not if I am in split mode. It
seems like it used to but I cannot make it work in split mode now. I'm
running FW 4.47. Any thoughts?
Stan - K6VWE
__
Elecraft mailing list
Home:
38 matches
Mail list logo