Is there any chance of getting the K3's line out level lowered? Even when set
to it's lowest level of 1, it puts out a bit too much audio for my TASCAM
US-100 external sound card. The TASCAM has an external input level control and
even with it all the way down, the K3 puts out too much audio
Jim,
I'm not familiar w/ your Tascam, but perhaps it's setup as a mic level
input (as opposed to line level)?
just a thought...
73,
Jeff KC9WSJ
On Tue, Jan 08, 2013 at 12:50:05PM -0600, Jim Sheldon wrote:
Is there any chance of getting the K3's line out level lowered? Even when
set to it's
I usually run the line out level around 20. If you need it to be less
than 1, you must be feeding a mic level input. Sounds like you need to
add an attenuator, if you can't use a line-level input.
73,
~iain / N6ML
On Tue, Jan 8, 2013 at 10:50 AM, Jim Sheldon w...@cox.net wrote:
Is there
...@mailman.qth.net] On Behalf Of iain macdonnell -
N6ML
Sent: Tuesday, January 08, 2013 10:57 AM
To: Jim Sheldon
Cc: Elecraft Mailing List
Subject: Re: [Elecraft] [K3] Line Out level
I usually run the line out level around 20. If you need it to be less than
1, you must be feeding a mic level input
/attenuator-cables.html
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of iain macdonnell -
N6ML
Sent: Tuesday, January 08, 2013 10:57 AM
To: Jim Sheldon
Cc: Elecraft Mailing List
Subject: Re: [Elecraft] [K3] Line
Greetings to the group!
Quick question: I normally keep the line out set to 5 or 10; I haven't seen
the need until now to increase it. I recently discovered a recording
utility built in to HRD, and leaving the line out level at 5 or 10 usually
results in a low-volume recording. I've fiddled
James,
You will not hurt the K3, but if the transformers saturate, you will get
distortion.
As long as the level of distortion is OK to your ears, I would judge
everything to be OK.
73,
Don W3FPR
James Sarte wrote:
Greetings to the group!
Quick question: I normally keep the line out set to
have found that a line output level of 50 is pretty good.
Hi James.
I use Audacity with the Lame MP3 plug-in to record beacons and intruders.
With the PC sound
card mic level at max, I need the K3 Line out at about 20 to get enough audio
for Audacity. Can't
hear any distortion but I'm
For digimodes like WSPR I use a Microham Digikeyer and set the K3 Line Out
level to 10, which
is the maximum recommended before the possibility of distortion is introduced.
At this level I have
to set the Digikeyer RX input control to max to obtain proper decoding etc and
being at maximum
limit audio levels.
73,
... Joe, W4TV
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Trevor Smithers
Sent: Thursday, October 01, 2009 6:49 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Line out level
:49 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Line out level and Digikeyer
For digimodes like WSPR I use a Microham Digikeyer and set
the K3 Line Out level to 10, which
is the maximum recommended before the possibility of
distortion is introduced. At this level I have
Thanks Lyle.
Looking forward to it !
-- Enno, PF5X
Lyle Johnson wrote:
I am experimenting with recording QSOs. If I want to record my own
transmission too, I have to set CONFIG: LIN OUT =PHONES...
A means to get tx audio without having to be in =PHONES is on the list.
73,
Lyle
Hi all,
I am experimenting with recording QSOs. If I want to record my own
transmission too, I have to set CONFIG: LIN OUT =PHONES. This links the line
out level to the AF pot meter settings. However, the level is too low for a
decent recording unless I want to blow my eardrums. When in LIN OUT
I am experimenting with recording QSOs. If I want to record my own
transmission too, I have to set CONFIG: LIN OUT =PHONES...
A means to get tx audio without having to be in =PHONES is on the list.
73,
Lyle KK7P
___
Elecraft mailing list
Post to:
14 matches
Mail list logo
