I use SpectraVue as a panoramic adapter with my K3 and three XV transverters.
Connected to the K3's IF out is an SDR-IQ, which is connected using the USB
port to my PC.
I don't have any issues with a 'variable frequency error' on 6 meters or any
other band. I can point and click to a signal
> Not if you connect via USB.
I am (was) connecting via USB.
73,
... Joe, W4TV
On 6/26/2013 4:56 PM, Wes Stewart wrote:
From: "Joe Subich, W4TV"
The only issue is the constantly changing IF offset in the
K3 (IS)
which SpectraVue does not track. This results in a variable
frequency
As a part of the referenced thread, that's not what it says at all.
--- On Wed, 6/26/13, amsct...@comcast.net wrote:
> From: amsct...@comcast.net
> Subject: Re: [Elecraft] K3 & SDR/IQ
> To: elecraft@mailman.qth.net
> Date: Wednesday, June 26, 2013, 12:21 PM
> Spectr
> From: "Joe Subich, W4TV"
>
> The only issue is the constantly changing IF offset in the
> K3 (IS)
> which SpectraVue does not track. This results in a variable
> frequency
> error based on mode.
Not if you connect via USB.
__
Ele
3 3:46:19 PM
Subject: Re: [Elecraft] K3 & SDR/IQ
> SpectraView's HF tracking mode doesn't allow for an IF tuning offset
> on frequencies higher than the design limit of the SDR-IQ itself. I
> know the IF frequency is well below that, but the software was never
> supporte
From: "Joe Subich, W4TV"
To: elecraft@mailman.qth.net
Sent: Wednesday, June 26, 2013 2:04:31 PM
Subject: Re: [Elecraft] K3 & SDR/IQ
On 6/26/2013 1:43 PM, Wes Stewart wrote:
LP-Bridge will handle the serial port issue.
Maybe - if none of your software uses one of the commands tha
: "Joe Subich, W4TV"
To: elecraft@mailman.qth.net
Sent: Wednesday, June 26, 2013 2:04:31 PM
Subject: Re: [Elecraft] K3 & SDR/IQ
On 6/26/2013 1:43 PM, Wes Stewart wrote:
> LP-Bridge will handle the serial port issue.
Maybe - if none of your software uses one of the comman
Joe Subich, W4TV wrote:
From: Joe Subich, W4TV
Subject: Re: [Elecraft] K3 & SDR/IQ
To: elecraft@mailman.qth.net
Date: Tuesday, June 25, 2013, 8:09 PM
> So how do yu set it up to watch lower end of 6m on the
K3, without
> using a transverter?
Connect SDR-IQ to the IF Out jack (n
LP-Bridge will handle the serial port issue. I run the K3, Spectravue, DXBase
and N1MM with one USB to Serial adapter and ports to spare.
--- On Tue, 6/25/13, Joe Subich, W4TV wrote:
> From: Joe Subich, W4TV
> Subject: Re: [Elecraft] K3 & SDR/IQ
> To: elecraft@mailman.q
ness.
Wes, N7WS
--- On Tue, 6/25/13, KD7YZ Bob wrote:
> From: KD7YZ Bob
> Subject: [Elecraft] K3 & SDR/IQ
> To: "'K3 List'"
> Date: Tuesday, June 25, 2013, 7:55 PM
> Howdy K3' people:
>
> I have an SDR/IQ. I also have three Elecraft transverters.
> So how do yu set it up to watch lower end of 6m on the K3, without
> using a transverter?
Connect SDR-IQ to the IF Out jack (not the RX Ant) and tune SpectraVue
to 8.125 MHz manually *or* in SV's "ExtRadio Setup" Select the K3 and
uncheck "HF Tracking Mode."
Note: If you want to use the fre
Howdy K3' people:
I have an SDR/IQ. I also have three Elecraft transverters. When I
connect a BNC to the BNC-RX "T" chain, and I tune Spectravue to 28.07
and the 6m xv50 transverter is "on", I am looking at the area around
50.070 .. I can look for beacons and Sporadic-E openings.
Nothing new.
Ho
On Thursday Wilhelm used a Straight-Key to send:
-Original Comment---
> Bob,
> You are OK.
> There is some bleed-through
"Whew!" .:B Thanks Don. And thanks too to Irizzary who replied.
--
Best regards,
Bob KD7YZWin7-64bit + K3
_
, 2012 09:58 AM
To: KD7YZ Bob
Cc: K3 List
Subject: Re: [Elecraft] K3 + SDR-IQ and regular CW operation
Bob,
You are OK.
There is some bleed-through of the IF output during transmit, and I
believe that is what you are seeing.
73.
Don W3FPR
On 12/13/2012 8:16 AM, KD7YZ Bob wrote:
> Howdy K3'
Bob,
You are OK.
There is some bleed-through of the IF output during transmit, and I
believe that is what you are seeing.
73.
Don W3FPR
On 12/13/2012 8:16 AM, KD7YZ Bob wrote:
Howdy K3' people:
I was wondering what precautions are taken, or I need to invoke, when I
use any form of transmitt
Howdy K3' people:
I was wondering what precautions are taken, or I need to invoke, when I
use any form of transmitting?
At present, the SDR-IQ is connected to the K3's IF BNC. K3's output is
through KAT500 then outside to the antenna some distance away at 80 to
85 feet AGL. Power, while I am test
Bob,
What are your specific questions? I have the K3 with SDR-IQ here.
I've used it both with the IF connection (as a panadapter) and with
an RF connection (RX Out/RX In and a splitter) for CW Skimmer.
It was in use for about a year but is off-line at the present - I'm
not completely sure the r
Howdy K3' people:
I did some more research on my goals of using my new K3, & Sub-RX with
matching 8-pole, for low-low bands.
If anyone uses the actual SDR-IQ with a K3, I would like some guidance.
And I' would like to ask is it possible to listen/hear a particular
point on the displayed segment w
: [Elecraft] K3 + SDR-IQ + CW Skimmer+ SpectraVue
Anyone know if it's possible to configure all four of the above to
simultaneously run CW Skimmer and SpectraVue? I have tired every possible
iteration to port audio from SpectraVue to CW Skimmer with no luck. I've
also tried VAC an
Anyone know if it's possible to configure all four of the above to
simultaneously run CW Skimmer and SpectraVue? I have tired every possible
iteration to port audio from SpectraVue to CW Skimmer with no luck. I've
also tried VAC and still no luck.
If there's anyone that's successfully tried t
I just received SDR-IQ and connected it to K3 via Etherlogic splitter with
Logger32. Tnx NI0C and NZ0T for assistance with Etherlogic. The PC was very
slow until I removed almost all the automatic startups.
Now, SDR-IQ runs smoothly except in a few situations.
After coming back from sleep, th
21 matches
Mail list logo