Thanks Mike - it was an ID-10T error: I had the RX antenna selected with
nothing on the RX antenna port.
73 de Lee, AA4GA
On Thu, May 11, 2023 at 9:47 PM Michael Carter wrote:
> Hi Lee,
>
> Do you also have a reduced RX signal level
> on 30 meters as well as 20 meters, at least
> by compariso
Hi Lee,
Do you also have a reduced RX signal level
on 30 meters as well as 20 meters, at least
by comparison with your KX3?
Since the TX output is OK, I will hazard a
guess that one of the relays in the
20/30M bandpass filter is not making
good contact or has developed a weak
solder joint on the
Glad you got it sorted out Lee73,Gary K9GS
Original message From: Lee Hiers Date:
5/11/23 5:21 PM (GMT-06:00) To: Elecraft Mailing List
Subject: Re: [Elecraft] K3 RX Issue? I thought about
quoting Jack Nicholson from A Few Good Men when he said"well don't I fe
I thought about quoting Jack Nicholson from A Few Good Men when he said
"well don't I feel like a" but thought better of it.
100% operator error. As diagnosed by N7GP and W0GHZ, I had my RX antenna
button pushed. I don't have an RX antenna, so I never push it...on
purpose.
I'm glad it wasn'
Hi All,
Recently I've noticed that signal levels have been down on 20m on my
K3/10. At first, I thought it was just band condx and didn't pay much
attention to it, but over the weekend I switched to the KX3 and signals
were much better - S-meter, P(X)3, and my ears...like maybe 30dB or so. 40
me
The suspect was pursued, caught, arrested and taken to the garbage with
the soldering iron. It was a defective pin diode that caused the loss of
10 dB. Thanks to all who have given me advice.
73 Udo, DK5YA
Am 02.11.2015 um 16:18 schrieb Udo Langenohl - DK5YA:
Gents,
in spring I made an upgra
#x27;;
elecraft@mailman.qth.net
Subject: RE: [Elecraft] K3 RX issue with KAT3A?
Jerry and Udo,
You can't save the configuration file from one K3 and then load it into
another K3. The configuration file contains the serial number and
calibration information specific to the K3 you're saving the configurat
2015 5:09 PM
To: 'Udo Langenohl - DK5YA' ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 RX issue with KAT3A?
Use the K3 utility to save the config from the "Good" K3, then use the same
utility to save the config from the "suspect" K3. Finally use the K3 Utility
to r
Adding the KAT3A gives you the possibility to be listening to a coax jack
with no antenna connected. To get started...
Make sure that CONFIG: KAT3 is *not* set to "not inst". Be certain of that
by hitting the "ANT" and "RXANT" buttons that you are on the coax connector
you intend. After that ther
craft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Udo
Langenohl - DK5YA
Sent: Monday, November 02, 2015 10:19 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 RX issue with KAT3A?
Gents,
in spring I made an upgrade to my K3 (#59xx) with the internal ATU KAT3A.
After this I guesse
Gents,
in spring I made an upgrade to my K3 (#59xx) with the internal ATU
KAT3A. After this I guessed that there is a noise drop on all bands from
160 up to 10, but was not 100% sure. The strange thing: neighbor
stations with similar setup always gave much better reports than me, at
least 10
11 matches
Mail list logo