Hi Chris;
I would stop using the radio immediately!
Sounds like the main audio chip U1 on the DSP board is going out.
When they fail, you can get a HI CUR warning because they are shorting out.
They can heat to the point of destroying the DSP board (which we don't
have anymore).
Digikey LM4950TS
Hi I have a strange problem with my K3/100.
The audio through the internal speaker is low, but comes up
much stronger with any slight movement of the volume knob.
Then it goes back down again, often accompanied by a brief
HI-CUR warning.
Also when AGC is turned off, audio is almost zero.
But, wit
This weekend I suddenly began to have an oscillation problem in the speaker amp
of my K3 (SN 969)) Headphones and the RX both work fine. I don’t hear the
strange audio oscillation in the headphones), but the speaker amp appears to be
having problems. If I turn on the speaker using SPKR+PH YES I
Contact Elecraft service. I had a similar problem a couple of years
ago. The radio had to go to the factory for diagnosis. We ended up
with a board replacement.
Ed
K6ED
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/
: elecraft@mailman.qth.net
Subject: [Elecraft] k3 audio problem
When I key the transmitter on SSB I hear a 700 or 800 hz tone being sent
along with the audio. Unable to figure out what is causing this. Any ideas?
Dick Blanchard, W1VVX
__
Elecra
When I key the transmitter on SSB I hear a 700 or 800 hz tone being sent along
with the audio. Unable to figure out what is causing this. Any ideas? Dick
Blanchard, W1VVX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/list
bias...
---
www.elecraft.com
On 11/14/2011 1:07 PM, Eric Swartz - WA6HHQ, Elecraft wrote:
> If they are using a condenser mic, make sure the mic boas is turned on.
>
> 73, Eric
>
> ---
> www.elecraft.com
>
>
__
Elecraft mailing list
Hom
If they are using a condenser mic, make sure the mic boas is turned on.
73, Eric
---
www.elecraft.com
On 11/14/2011 1:02 PM, Greg wrote:
> Garry,
>
> I am not at home right. Using another radio's config file will probably
> not work as the calibrations would be different between the two rigs.
Garry,
I am not at home right. Using another radio's config file will probably
not work as the calibrations would be different between the two rigs.
If you can get them on the air or by email I would suggest doing the EEINIT
process and then redo the calibrations outlined in the manual (watt met
I called them and worked them but was unable to make a suggestion to them that
they
download the same configuration file as used by the other K3, and re-start it.
Maybe
they have already tried this, I don't know.
VY 73, Lance
On 11/14/2011 8:27 PM, Garry Shapiro wrote:
> Just spoke to VK4FW
Just spoke to VK4FW at T2T. One of their K3's works on CW but has died
on SSB. Bill says they disconnected all cables, set all settings to
match another K3 that is working on SSB, checked the microphone routing
on the Main Menu and of course swapped out headsets. No joy. They are
frantic to get
Don Wilhelm-4 wrote:
>
> John,
>
> I believe that HRD and DM780 does not provide a path for audio, you must
> use something like Skype in addition to hear the audio on the local
> computer.
>
> 73,
> Don W3FPR
>
> John K9UWA wrote:
>> I have my K3 hooked to a computer and all functions on
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: htt
John,
I believe that HRD and DM780 does not provide a path for audio, you must
use something like Skype in addition to hear the audio on the local
computer.
73,
Don W3FPR
John K9UWA wrote:
> I have my K3 hooked to a computer and all functions on it work fine through
> Ham Radio Deluxe and DM7
I have my K3 hooked to a computer and all functions on it work fine through Ham
Radio Deluxe and DM780 with an attached
K1EL Keyer.
I am then attempting to access this K3 and its computer over my in home network
from another computer. This one they call the
Local Computer. I have the Computer co
Hello,
Last night I was transmitting on 160m and using stereo headphones listening
with diversity RX and heard some unusual clicking coming from the K3 when
transmitting. I pulled the diversity RX antenna that was plugged into the 2nd
RX antenna port with no change. I pulled the RX antenna t
My DSP board failed 4 months after the kit K3 #818 was assembled.
I had no audio anywhere. The S meter showed almost full scale. The receiver
resting current went from .85 to 1.01 amps. Replacement KIO3 boards did not
cure the problem. Gary at Elecraft suggested it might be the DSP board if
On Mon, 7 Jul 2008 11:41:03 -0400, "Gary Nichols" <[EMAIL PROTECTED]> wrote:
[snip]
>Hello all, CW is working fine with K3 #716 but trying SSB there seems to be
>a problem possibly related to the headset/boom mic I had been using with
>other radios. If I turn the monitor up enough to hear anything
_
From: Gary Nichols [mailto:[EMAIL PROTECTED]
Sent: Monday, July 07, 2008 11:15 AM
To: elecraft@mailman.qth.net
Subject: audio problems?
Hello all, CW is working fine with K3 #716 but trying SSB there seems to be
a problem possibly related to the headset/boom m
19 matches
Mail list logo