You will also need a means of making the K3 go into transmit. A
work-around would be to use VOX.
John G4ZTR
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Don Wilhelm
Sent: 18 October 2011 22:22
To:
On 10/19/2011 12:12 AM, John Lemay wrote:
You will also need a means of making the K3 go into transmit. A
work-around would be to use VOX.
Not a work-around at all -- that works VERY well. I do a LOT of
contesting, and a fair amount of FSK441, JT65, and ISCAT, and I've never
felt the need
Question... how will the resolution selection be controlled? Through P3
firmware?
Looking forward to this addition... the eyes aren't getting any younger!
73 de Jim - KE8G
Alan Bloom n...@sonic.net wrote:
The plan is: 1024x768, 1280x1024 and 1920x1080.
Alan N1AL
On Mon,
I removed all the boards added with krx3, connected again all without the
boards removed (not closed the chassis) and powered on the K3.bad news, the
problem is still there so i must assume it's a problem occurred when i
connected the front panel with the aux dsp mounted to the k3. Now
Using F/W upgrade 4.39.
I just noticed that when I push the spot button the K3 will QSY down a
little over 2 khz. It is never the exact same amount. It does not
necessarily stop on a signal. This happens when I have a CW signal in the
passband or not. The last three times I did the calculation it
Robby
It sounds to me like you have autospot enabled. I'm not sitting in front of
the K3 at the moment to check. That will go qsying away in search of a tone
when there isn't one, so that would make some sort of sense. Can't remember
how to turn it off though!
73 Stephen G4SJP
On Wednesday, 19
Hi Stephen Robby,
Autospot is turned on when the CWT is activated. You can see this on the S
meter display. With CWT activated, the right half of the S meter display
shows the CWT tuning bar. Press the CWT button to toggle it on and off. As
Stephen indicated, with CWT active the SPOT button
The KAT500 tuner has two antenna outputs that can be switched in this manner.
We are in final test and development on this right now.
73,
Eric
www.elecraft.com
_..._
On Oct 18, 2011, at 7:27 PM, tomb18 tom...@videotron.ca wrote:
Can anyone suggest a way to attach two antennas to the
Can anyone tell me what transistors are used in the PA on the KPA500. I can't
seem to find it in the specifications and I still do not see a schematic
available. The link to a schematic listed a few days ago requires registration
on that website to access it and I do not care to do that.
VRF2933.
73,
Bob, N6CM
On Wed, Oct 19, 2011 at 9:28 AM, Robert Dorchuck W6VY w...@yahoo.comwrote:
Can anyone tell me what transistors are used in the PA on the KPA500. I
can't seem to find it in the specifications and I still do not see a
schematic available. The link to a schematic listed
Wondering if it's safe to upgrade to Lion.
-
Chuck, KE9UW
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Do-Utilities-work-with-Lion-tp6909480p6909480.html
Sent from the Elecraft mailing list archive at Nabble.com.
They do for me. Lion is a great OS. Go for it!
Jack Brindle, W6FB
On Oct 19, 2011, at 9:47 AM, ke9uw wrote:
Wondering if it's safe to upgrade to Lion.
-
Chuck, KE9UW
--
View this message in context:
Great. Thanks.
Sent from my iPad
On Oct 19, 2011, at 11:57 AM, Jack Brindle jackbrin...@me.com wrote:
They do for me. Lion is a great OS. Go for it!
Jack Brindle, W6FB
On Oct 19, 2011, at 9:47 AM, ke9uw wrote:
Wondering if it's safe to upgrade to Lion.
-
Chuck, KE9UW
--
Thanks for all the answers and the schematic pdf. And I finally found the
reference to the transistors in the Theory of Operation in the owners manual -
did not see it the first time I looked (must be getting old).
Thanks to all that replied.
Bob W6VY
--- On Wed, 10/19/11, Bob k...@att.net
Rob,
www.bugmenot.com is handy for websites that require registration - including
this one :)
73, Thomas M0TRN
On 19 October 2011 19:09, Robert Dorchuck W6VY w...@yahoo.com wrote:
Thanks for all the answers and the schematic pdf. And I finally found the
reference to the transistors in the
Don,
I have been reading this with interest. Just wanted to add a word of support.
I have made two 80 meter loops fed with 450 ohm ladder line. A 160m loop is
just larger. I have used a Johnson Viking Matchbox tuner, and one with a
roller inductor with them. (I use a MFJ-212 Matchmaker to
Until the KAT500 comes along I am presently using a two-position antenna
switch connected to the amp's output. One line goes to my Rat Pak
6-position remote antenna switch, the other goes to my 12m rotatable dipole
that I recently added to my ant. farm.
Yes, a few times I've forgotten to switch
Others have mentioned the Autospot feature, and here's an observation on
that as it relates to your issue of a large freq change.
If my freq resolution is at 10Hz or 100Hz and I try to Autospot, I will
get a 2kHz shift as you described. If, however, I am set to 1Hz
resolution, the Autospot
What firmware version is being used? When using the auto tune function the
radio should go into fine tune mode and then turn it off after the tuning is
done.
73
Greg
On Wed, Oct 19, 2011 at 3:52 PM, Dennis Moore den...@mail4life.net wrote:
Others have mentioned the Autospot feature, and
I'm using 4.39. I just tested it to double check my previous statement.
In 10Hz tuning mode it IS changing to 1Hz mode and tuning properly. In
coarse tune mode (100 Hz), it is not changing tuning rate. I withdraw my
statement about the 10Hz but stand by the 100Hz.
Thanks for making me check!
Note that the CWT indicator range, upon which the autospot function is
based, is only about 200 Hz wide. In 100 Hz step mode, you'd have to be
less than 1 step away from zero beat for the function to work.
73,
Lyle KK7P
I'm using 4.39. I just tested it to double check my previous statement.
I feel that I have a problem with my W2, when I connect the directional
coupler to my K3/100 s/n 05779, it indicates what I think is the correct
SWR and Power out, swr 1.1 to 1.2, then the atu brings it back to 1.0
however, when I connect the directional coupler to the output of my KPA500
the W2
So, if I was going to purchase a monitor, say 23-25 diagonal, what
should I look for besides the 1920 X 1080P resolution?
Pixel response time? 5ms seems to be the norm.
I assume a 16:9 aspect ratio?
Does contrast ratio make a difference?
I assume I'll want one with a VGA interface, not DVI or
Alan,
Check that you have the coupler connected in the right direction when you
have it on the KPA500. From your description, it sounds like it is
connected backwards.
73,
Bob, N6CM
On Wed, Oct 19, 2011 at 7:56 PM, Alan Grant asgr...@aapt.net.au wrote:
I feel that I have a problem with my
Alan, do you have the coupler oriented correctly with the TRANSMITTER end
connected to the KPA500 and the LOAD connected to the antenna. It sounds
like you have it backwards so the W2 is reading the reflected power as
forward (20-30 watts) and the forward power as reflected which would
trigger a
Hi Guys and Gals,
Does anyone know of a mod to the Elecraft XV transverters that provides for
10 Mhz GPS disciplined oscillator control of the transverter local
oscillator?
I think that would be a popular feature for Elecraft to consider on future
versions of XV transverters. It would be
26 matches
Mail list logo
