Jerry,
Thanks for the response. I'm curious, however, why removing the 100W PA and
running calibration tests at 10W would matter, if I'm already seeing
expected results at the 10W power level. That is, I set the output power on
my K3 to 10W, and transmit using a full duty cycle mode. On the
Chris, please let us know the 'how to' when you have it up and running.
73 David G3WGN M6O WJ6O
Chris Tate - N6WM wrote
> Thanks Brian and thanks to Jack W6 F ine B usiness for getting back to
Because there's a specific calibration process during build that's performed
on the 10w system prior to installing the 100w amp.
With the 100w amp in place and the jumpers configured the data is
speculative as to which circuits are in operation.
The key to troubleshooting is to isolate. Don't
> With the 100w amp in place and the jumpers configured the data is
> speculative as to which circuits are in operation.
It is not necessary to remove the 100W amp. Simply dial the power
back below 12W and it will be bypassed. Thus my procedure to check
power at 5.5/10 and 55/100 W ... using
I am hoping to use a K3 to transverter from 14 MHz to 144 MHz with an existing
transverter.
I need to cover from 14.000 to about 14.400 MHz on transmit for the weak signal
end of the band.
I believe that the K3 can be enabled via software to transmit outside the
limits of the ham bands.
The
Ian,
Either the LPA or the KPA is compressing above 5/50W.
Set the K3 to 5.5 watts and check power output on each band. Then set
the K3 to 10 watts and check power output on each band. Then repeat
the process at 55 and 100 watts.
That should tell you if the LPA or KPA is compressing and
Just go to the ORDER page …
Grant NQ5T
K3 #2091, KX3 #8342
> On Feb 24, 2016, at 12:46 PM, Fred Jensen wrote:
>
> Someone said the rubber ring for the K3 main knob is available from Elecraft.
> How do I find it on the web page?
>
> 73,
>
> Fred K6DGW
> - Northern
My suggestions are LMR400UF or Andrew FSJ1-50. They are the only cables I
use for low-power jumpers in my shack. Down stream from my larger amps, I
use LMR600UF. BTW, Tessco is a great place to buy all of your cable and
connector hardware.
Alan - N7MIT
--
View this message in
Bill,
I use HRD on Windows 10 and have not noticed any slowdowns. Could the drive
you're experiencing issues on need defragmenting? Is one drive solid state
vs. the other drive being SATA or some other older bus type?
Thanks and 73,
--Ian
Ian Kahn, KM4IK
Roswell, GA EM74ua
km4ik@gmail.com
Identical SSDs. Never defrag same! Only difference is the one is up to
date and the other is out of date by about four weeks.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Hello Bill,
During normal operation there a no clicks when changing a filter.
My K3 is an older one, but ever since I have the NEW SYNTH's on board,
there's a lot of clicking going on when I change the width of the
filters in Diversity mode.
Nothing to worry about. I think the relays are on
Just a comment on Times Microwave LMR cables:
In outdoor application its "VERY" important to seal connectors properly.
The aluminum tape shield oxidizes in presence of moisture with
resulting change in impedance and attenuation. I just replaced a
45-foot run of LMR-600 which hangs off my eme
For exterior use, I choose to use the LMR-xxx-DB series which is
impregnated with a moisture reduction substance intended for direct
burial, it adds an additional measure of protection.
__
Clay Autery, KG5LKV
MONTAC Enterprises
(318) 518-1389
On 2/24/2016 11:39 AM,
Someone said the rubber ring for the K3 main knob is available from
Elecraft. How do I find it on the web page?
73,
Fred K6DGW
- Northern California Contest Club
- CU in the Cal QSO Party 1-2 Oct 2016
- www.cqp.org
__
Elecraft
NEOGRIP on our product list and product order pages.
http://www.elecraft.com/elecraft_prod_list.htm
http://www.elecraft.com/elecraft_prod_list.htm#kio3bupkt
73 de Dick, K6KR
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Fred
Jensen
Sent:
Typoit is a Hakko 936sorry.
- Original Message -
From: a...@cablespeed.com
To: Elecraft Reflector
Sent: Wed, 24 Feb 2016 11:19:16 -0500 (EST)
Subject: [Elecraft] panavise and hakko 963
The Panavise is sold.Hakko 963 still available.
Still
I recently posted about comparing prices between importing directly from
Elecraft USA and buying in the UK from the dealer at £ for $ prices. I
originally thought that it would be considerably less expensive, though risky
if warranty repair was ever required, to directly import.
I now realise
The Panavise is sold.Hakko 963 still available.
Still cleaning out the closet. I have a panavise base with the small circuit
board holder and a large circuit board holder.
$50 plus shipping. Should fit in a medium priority mail box.
Also have an older Hakko 963. Not pretty but it
It took two tries, but finally got traces and frequency stability good enough
on my Kx3 for JT mode on 2 meters, using the internal 2m transverter. TX/RX
recovery at 2w output showed minimal frequency change for a few seconds.I used
the Px3 to evaluate the frequency of the signal generator over
Have you talked to my support staff?
Rick - W4PC
http://tickets.hrdsoftwarellc.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill
Sent: Wednesday, February 24, 2016 3:50 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] HRD question
Has
Is there any projected ETA on a P3 firmware release to get #macros (ones
directed to the P3 itself) to execute from P3 keyboard macros? I
forgot these don't work yet and am stuck until they do! Beta please :)
Warren, KD4Z
__
Elecraft
This is me, not for all folks ok?
1.8 filter installed, Hi Cut set to 1.7 - 1.8, Lo Cut set to .10.
Now, to MY EARS 99% of stations I work are perfect to my ears.
I defer to excellent advice from Jim, k9yc and othersyou know who you are.
On the RX EQ, I have -16db on 1-3, 4-6 are flat, 7-8 are
Dear Sir,
Why is my personnel information being published from this web sight to the
internet open area for all to see? I thought this group was for elecraft not
the rest of the world. I found my name and e-mail address published and i did
not authorize my personnel info from this web sight to
The mailman software being used archives the list for posterity and that
archive is made available online at
http://mailman.qth.net/pipermail/elecraft/. The various search engines
index the archive on a regular basis.
It's always possible to use your ARRL email address instead so you can hide
Vincent:
You seem not to understand the nature of this email reflector. Anything posted
on this reflector can be viewed by anyone with access to the internet. This is
stated clearly on the web page describing the reflector,
http://www.elecraft.com/elist.html. You will note a link to "Elecraft
I have my K3/100 for sale. I purchased it as a kit, S/N 5508, on 5/27/11.
It's been in a non-smoking environment sharing a desktop with two other HF
rigs, so it has not seen full-time duty. The following are included:
K3/100
KAT3 ATU
KXV3A RX Ant., IF Out and Xverter Interface
KFL3A 1.8kHz
Hello all,
I have for sale a QRP Works Key Log Go. The unit is in impeccable
condition, never exposed to rain, moisture or harsh conditions, working very
well. Overall I've been quite happy with it. I am selling because I
decided that the QRP Works SideKar is probably better suited to my
Has any one experienced a distinct slowdown of HRD initiating on Win 10?
I just put a Win 10 drive on my computer from about six weeks ago and it
initiates in about six seconds. On the current Win 10 drive, it takes
about 25 seconds. The only difference between the drives is that the
slower
Thanks Arie... I would still like to hear from ELECRAFT why my other K3 with
New Synth boards DO Not have these relay clicks but my newest K3 89XX does.
Not sure I'm ready to accept that all is well until someone can explain what
is happening with these clicking noises.
Thanks for your input.
Hello again,
I did a couple of runs on the Kx3 with 50 seconds on TX and then reading
the frequency drift at 144.000MHz. Here is what I found out. My question is
whether it is good enough for JT mode on that frequency. Let me also sat that
the stability at the HF bands is very good. This
Bill,
Just as a wild guess, do you have matched filters in one and some
unmatched filters in the other?
With the new synth boards and the updated software, you can do diversity
without matched filters, but the K3 handles the synthesizers differently
that it does with matched filters.
If you
Have a new K3S and need to find the best settings.
What are people using for their SSB and CW RX EQ 8 band settings.
Same for the SSB Lo and Hi cut points.
What seems to be the best NR settings.
Thanks
Doug/VA5DX
"Only the fool sayeth there is no God." - From the movie 'The Miracle of Our
Lady of
HRD initiates here in less than 5 seconds with Win 10 and all current
updates.
3.4 GHz i7 and 12 GB RAM.
But, I am using HRD 6.3.0.483
73,
Jim - N4ST
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill
Sent: Wednesday, February 24, 2016
SSDs should not need de-fragmenting.
The problem with fragmented disk volumes is that the parts of a file get
scattered all of the disk. That means it takes multiple seeks to get an entire
file. De-fragmenting organizes each file in neighboring blocks on the same
cylinder, so the file can be
Not nearly good enough for JT65b on 144 MHz. Have you done the temperature
compensation?
I use my KX3 on 144 MHz but the difference is I am using a transverter with an
IF of 14 MHz where the drift is proportionally less to start with and the
external transverter has a very high stability TCXO
Here the filters that are in my K3 SN89XX. The SAME filters are in both the
MAIN and the SUB receiver 2.7, 1.8, 700, 400, 200. The radio has all new
SW loaded last Thursday when the sub receiver and filters were added. I
checked the K3 utility program and they are configured the same in both
Doug,
This is not a question where there is a 'best' setting for everyone - it
all depends.
Your RX EQ settings will have to be customized to your ears and the
listening devices you typically use (headphones, speakers, etc.).
I just leave mine set flat for both SSB and CW. Make it sound
I have never purchased - still using the same version for years. Hence,
no calls to your support. But, thanks for the offer.
That said, I really do not feel this is an HRD issue - more like
something leaking in from Windows 10 and a faulty update. Else why the
huge difference using a version
38 matches
Mail list logo