Even the second receiver has a big influence on how your signal sounds.
At present I am building my version of a wideband monitor receiver designed by
Ian G4COL, and featured in the RSGB Rad Com of November 1990.
As this has no pass band filtering to colour the received signal, combined with
an
Oops, I said KDSP2, when I meant to say KPSK2, my name for that tight little
board over TP2. I Got a nasty RF burn on my lip in 1981 from a HW-101,
D-104, Unbalanced short low crappy ungrounded antenna, and haven't had much
use for sideband ever since. But I did struggle with my KSB2 recently
Problem Solved
With the Gracious Help of Don and Gary, the trouble with my K2 transmitting on
Power up has been solved. It turned out to be a Bad Q2 on the COntrol Board.
Both of these guys have provided wonderful help in solving this problem. No on
to the alignment stages.
73 Bruce
Hello group,
I'm not sure where else to ask this question. I can't seem to get anything
but an answering machine at the Kenwood Amateur Radio Tech support Center.
While waiting for a new K2, I would like to get on the air (after a
considerable absence) with an old (but very good) TS-820S. The
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I'm Cyrille DERORY, a french who is living near the city of Brest.
This is my first K2 (serial 4542) with optionals : SSB, 160m, KIO. The
AF sound is ok with headphones connected on the front panel. However
without headphones, the audio signal is very low AF power on the
internel speaker or
Cyrille:
My best guess is that you have reversed the wires in SPK-J1 - The connector
on the cover. OR you have reversed the ground (earth) on SPK-J2 - The
speaker jack on the rear of the cover.
Remove the cover and set it away from the base, Disconnect the internal
battery if you have it, just
SECOND CLASS OPERATOR'S CLUB (SOC) MARATHON SPRINT
_
Most sprints run four hours, but since we're Second Class Op's,
we need more time!
Hi, Tom.
Tom Skinner wrote:
Hello group,
I'm not sure where else to ask this question. I can't seem to get anything but
an answering machine at the Kenwood Amateur Radio Tech support Center.
While waiting for a new K2, I would like to get on the air (after a
considerable absence) with an
Hello all (again). I'm attempting to align the VCO and am having
trouble making it lock on all bands or get to the right voltage range.
I've verified all components on the board and touched up the solder
on the pertinent components and relays (and verified all
paths/continuity), but nothing
Tom,
I don't know about the TS-820S, but if the finals are run in linear mode for
both CW and SSB, you can safely reduce the drive without hurting anything.
If your TS-820 has a drive control, I would think it would be safe to use it
to reduce the drive.
OTOH, (just as a cautionary note) a few
Tim,
Check and re-check the capacitor values. From the bands that seem to me to
have strange voltage readings, C73 (should be 47pf) and C74 (should be 20
pf) are the most likely culprits.
Other things to check: be certain the menu parameter for D19 is OFF - check
the relays K13, K14 and K15, set
I'm trying to get TRX Manager to talk to my K2 over a
COM port (Win XP, COM3 as an add-on card) but it won't
see it.
Writelog can talk to the K2 with the same cable, port,
etc. TRX talks fine to my FT1000MP MkV on COM1.
I've read the instructions in TRX Manager about the K2
and experimented
Hi All,
Am working on putting my secound K2 together, have run into a bit of
a problem,
am on the first light alignment and test, part 1, K2 powers up, info 201
comes on
(and disapears) then the elecraft and 7100.cc c, everything seems fine to that
point,
but, not a single button
Thanks Fraser, Don Rick,
I was hoping this would be the case.
As I mentioned to Fraser, thanks to the Elecraft crew and all the users.
This whole K2/QRP thing has rekindled my enthusiasm for ham radio since
being off the air more than 25 years - 2 years as KG4TS pretty much burned
me out!
OK, Left Coasters, what is it
- Original Message -
From: Trev - K6ESE [EMAIL PROTECTED]
To: Elecraft Reflector elecraft@mailman.qth.net
Sent: Thursday, February 24, 2005 11:38 PM
Subject: Re: [Elecraft] New Elecraft product to be shown at RadioFest
onSaturday
Oh dog gone it I
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
This is from the HFPack list
QUOTE
It is a tuner and was unveiled at the NorCal meeting according to a
posting in the SG-2020 Yahoo Site. Go here for details:
http://www.norcalqrp.org/mtg2005_02.htm
73
Gene K1NR
/QUOTE
Scroll down BTW, it is
H..Today, new rig.
I bet a cup of coffee it is a K2 like rig. It will cover 160-6M standard.
They want to compete with the Argo, so I think the new offering will have
25W out max.
Am I even close?
___
Elecraft mailing list
Post to:
Oh, come on. The hamfest ended about 45 minutes ago. BUT, if you have
been paying attention to the list, you have already seen the new
product!
;-) :-) :-)
On Feb 26, 2005, at 2:35 PM, Alan Fryer wrote:
OK, Left Coasters, what is it
- Original Message -
From: Trev - K6ESE
Items For Sale:
---
1. K2 #2534 MCU 2.01H IOC 102
With:
- KSB2 - SSB option V104
- KNB2 - Noise Blanker V102
- KAF2 - Audio filter V1.00
- Heil MH2 hand mic
Works great. Checked out by Elecraft about two years ago.
All documentation included.
Price:
Ken,
Since you can see the display - and it seems to be proper, many of the front
panel signals must be correct.
I would look closely at the SR CK signal on the control board and on the
front panel board since this signal is common to the circuits that you
report as failing. Check the
Check and re-check the capacitor values. From the bands that seem to me to
have strange voltage readings, C73 (should be 47pf) and C74 (should be 20
pf) are the most likely culprits.
Not the caps (after a quick trip to Radio Shack to pick up a new 20pf and 47pf).
Other things to check: be
This is a test message to see that I am getting this message to the
Reflector..
Paul Gates
Elecraft K1 #231
[EMAIL PROTECTED]
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info
I received my KDSP2 a couple of days ago. Just got around to
checking out the parts bags this afternoon. I haven't done an inventory yet,
but I did do a check to make sure all the big pieces were there and I
cannot find the E100179 circuit board anywhere. It's not like there are very
many
I recently purchased the K2 PLL Temp Comp mod kit, and it came with Rev
D (3 Feb 04) instructions. A couple places in the instructions mention
replacing L31 (originally 10uH, which my rig has) with a 12 uH inductor.
Yet the parts list states it should be a 10 uH, and I was shipped a 10 uH.
Mike,
Yes, ignore that inductor change. The inductor necessary depends a lot on
the crystal that shipped with your kit, and the proper value has changed
from 10 uH to 12 uH and back a few times over the life of the K2. Put in
the 10 uH (or re-use the one that is currently installed) and wait
I just did the 1st aliment smoke test. Put power to it for the first time.
When I turn it on, after a second, something clicks. The display is lit but
nothing else. No letters or anything. Now what? I wonder if it's one of those
main chips. I got this kit partially assembled in a box.
Roland,
That sounds like the behavior one would see if the control board is not
properly plugged in.
Since you received the kit partially built, you should first gain confidence
in what the previous builder has done. I suggest that you go through the
steps in the manual (starting at the
In a message dated 27/02/05 03:13:02 GMT Standard Time, [EMAIL PROTECTED]
writes:
I just did the 1st aliment smoke test. Put power to it for the first
time. When I turn it on, after a second, something clicks. The display is
lit
but nothing else. No letters or anything. Now what?
The two blue pots on the audio filter seem to offer a great range of audio
filtering.
However with the pots and software, I cannot get on effect I want.
It might be impossible to do even if I mod it. I simply want to lower the
noise floor.
The noise floor is low. However I wanted to try to
Hello Tom,
Having spent countless hours in the company of members of the 6146 family,
from their conception, please be assured that even with zero RF signal drive
a 6146B will be undamaged provided that 1) Supply voltages are within
specified limits 2) Real DC bias is used for the control grid
OK folks,
It's nearly Sunday (30 minutes to go)
For the benefit of the majority that DIDN'T manage to get to
the HamFest...
What is the new product ???
Pretty Please ???
Dave KK7SS
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
Good Evening,
Once again I had a very late night in the big city. The campiest
production of a Shakespeare play I've seen since the scene in The Magic
Christian.
Last night I made a good contact into South Dakota on 40 meters and the
Fox hunt went well on Thursday evening so that band
33 matches
Mail list logo