Olli,
Referring to page 8 in the K3 Owner's Manual (may be a different page
for the K3s):
"Frequency Stability +/- 5 ppm for the TCXO standard; +/- 1ppm for
the optional TCXO."
TCXO-1 and TCXO-3 respectively mentioned above.
ppm means one part per million (1Hz per million Hz which is 1Hz
I have two of these, brand new in the box.
$140 each, shipped to lower 48.
73 de na6m
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Clay,
Use twisted pair wire between the switch and the RCA Plug. The tighter
the twist the better.
If you use that, there is no need for shielding.
If you do use a shield, connect it to the outside of the enclosure of
the K3S (the RCA jack is grounded, but not to the outside of the
Well, I'm not BUYING any Canare cable... just re-purposing 1/3 of a
component cable I made a long time ago (and haven't needed in a decade),
OR using some leftover Star Quad (if I can find it). I happen to have
50 NEW, unused Canare RCA connectors in the size required for L5-CFB
cable (think
I’ve never had any problem with RFI on my footswitch, running legal limit from
not all that far away. Any old shielded cable ought to do just fine — think
Radio Shack quality junk.
Certainly no need for Canare in this application.
Grant NQ5T
K3 #2091, KX3 #8342
> On Mar 12, 2016, at 3:46
Hooking up a Linemaster Clipper Model No. 632-S to my K3s rear PTT RCA jack.
Obviously, the RCA is 2-conductor unbalanced and there is no issue about
which terminals to use on the foot switch for normally open switching.
BUT, I want to make sure the foot switch cable is never an issue for RFI
in
Must be D5. Removing the KXV3 and shorting pins 8 &10 and 13 & 15 on its
socket restores full sensitivity to the Main receiver. Thanks again, guys.
73...
Randy, W8FN
On 3/12/2016 1:32 PM, Randy Farmer wrote:
Excellent! Thanks to Dave, Joe and Don for the useful information. The
K3 is now on
Excellent! Thanks to Dave, Joe and Don for the useful information. The
K3 is now on the bench and I'll start work soon. It most likely is D5 on
the KXV3.
Thank y'all for the quick response.
73...
Randy, W8FN
On 3/12/2016 9:43 AM, Don Wilhelm wrote:
Randy,
I suggest you contact K3support -
There's a KXPA Utility configuration option to disable ANT 1 or ANT 2, per
band. Could you check that?
73 de Dick, K6KR
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Max
Cotton
Sent: Saturday, March 12, 2016 09:53
To: elecraft@mailman.qth.net
Bear with me because this is from my memory. To the best of my knowledge you
have to use the up button and down button to change values and cannot directly
enter the value. As I recall Wayne stated it would be added to a future
revision but apparently isn't present in the firmware you have
Attempting to set up K3s to do the following as per example in KE7X
manual, p 212, under Macro Sequencing. His example is to program Macro 4
to change the AGC THR to 020 and Macro 5 to AGC 012 by using a Tap of
M1. I do not wish to lose the ability to send cw with M1 so wish to use
M4.
Here is
Title says it all, works fine on ant 1 but will not switch to Ant 2. relay is
OK. Ideas? before I do any deep diagnostics.73, Max W8BX
__
Elecraft mailing list
Home:
Here ya go:
http://marc.info/?l=elecraft=145323127930319=2
If you have the KXV3 installed, it is probably D5. I checked the
Mouser part number for the heavy-duty replacement, and it's still
good.
Dave Hachadorian, K6LL
Yuma, AZ
-Original Message-
From: Randy Farmer
Sent:
Randy,
Is the main RX dead all the time (when using only Main RX - Sub RX
off)?
Two quick things to check ...
1) if the Main RX is dead all the time and you have KXV3/A/B boards
in each rig, swap them. If the problem moves with the KXV3, the
problem is most likely D5.
2) If the Main
Randy,
I suggest you contact K3support - they can likely give you a small
number of probable failure points. That will allow you to choose field
repair or send it to Watsonville.
73,
Don W3FPR
On 3/12/2016 10:36 AM, Randy Farmer wrote:
Due to an unlucky combination of station configuration
Due to an unlucky combination of station configuration and a bad TX gain
calibration in my K3s (since corrected) I've managed to burn out
something in the front end chain in my second station K3. I've verified
the problem is in the signal path between the ATU inputs and the input
to the main
Elecraft K3/100; Late #7504, which includes all factory upgrades.
This is an excellent useable K3, out of the box.
K3SYN3AUPG newest Synthesizer option installed. This significantly improves
receiver performance.
KXV3A Receive ANT IF out and XVRTR Interface board.
KIO3 I/O board option.
Oliver, I was wondering about this, I guess it is just that the short term
drift is lower so it won't drift as much between frequency measurement
corrections which are made for 1 second every 4 seconds according to some info
recently published. I doubt it matters much though. I would be tempted
I have purchased a new K3s and no longer have use for my old
K3 friend #202. Of course, it is not pristine having been
opened up and put back together many times over the last 9
year, but it is fully functional and has been well
maintained over the years with all known official mods and
19 matches
Mail list logo