After some years of both a 13 and 6 kHz filter in my K3 with sub-RX, I gave
up on the 13 kHz as not being particularly useful as I wound up never
listening to FM on my K3.
On the other hand I frequently4 used the 6 kHz filter on AM in the "Sync"
mode, which uses USB and LSB demodulation, but
I've got one. Works well.
On 6/25/2016 7:57 PM, Phil Wheeler wrote:
This one
https://proaudioeng.com/products/pae-kx33-low-rfi-ac-power-supply/
73, Phil W7OX
On 6/25/16 6:59 PM, johnpierce wrote:
A person recently provided a link to a clean Wall Wart power supply he
bought for his KX3. I
Hi All,
I stumbled my way through the rest of the XV432 transverter alignment
and everything appears to be fine. Just trying to do the transverter
band setup from page 21 in the KX3 manual.
"XVn RF sets the operating frequency". I assume this means the
transverter's operating frequency?
This one
https://proaudioeng.com/products/pae-kx33-low-rfi-ac-power-supply/
73, Phil W7OX
On 6/25/16 6:59 PM, johnpierce wrote:
A person recently provided a link to a clean Wall Wart power supply he
bought for his KX3. I have searched for it and cannot find it. Could
someone please repost
A person recently provided a link to a clean Wall Wart power supply he
bought for his KX3. I have searched for it and cannot find it. Could
someone please repost the link?
John Pierce
__
Elecraft mailing list
Home:
Howie,
Have you set QRQ on? Shift is not available while QRQ is turned on.
73,
Don W3FPR
On 6/25/2016 8:46 PM, hhoyt wrote:
In the middle of field day my K3 filter center frequency control decided to become unresponsive and will not switch modes by tapping and is stuck to the center
Don't forget, when you get the unit with the xfmr removed, to install the
Belleville washer correctly as shown in the kit assy manual. That's
important to hold the transformer in place.
73, Ron AC7AC
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf
In the middle of field day my K3 filter center frequency control decided to
become unresponsive and will not switch modes by tapping and is stuck to the
center spot frequency. Any ideas?
Howie - WA4PSC
Sent via the Samsung GALAXY S® 5, an AT 4G LTE smartphone
Thanks Don,
That is exactly the info I was looking for. I had shipped mine back,
w/o xformer, for a repair last year but wondered how does Elecraft ship
Factory built units.
Ralph W1ZK
On 6/25/2016 8:26 PM, Don Wilhelm wrote:
Ralph,
When a KPA500 is shipped for service, they recommend
Ralph,
When a KPA500 is shipped for service, they recommend that the
transformer be removed.
It not only saves on weight, but it eliminates the possibility that the
transformer will deform the bottom panel should the parcel experience a
sudden stop such as at the end of a sorting chute.
My factory assembled KPA-500 was shipped in one carton, all parts installed.
Set the line voltage and install the fuses, and you're off to the races!
73,
Cliff K3LL/6
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ralph
McClintock
Sent:
What does Elecraft recommend for shipping a built KPA-500? Do KPA-500F
amps ship with the xformer installed? Not selling mine, just wondering
about buying a used one!!
W1ZK
--
Secretary USS PUEBLO Veterans Association
Life Member American Ex-Prisoners of War
Life Member Disabled American
You might be surprised Joe. Demodulating double sideband AM with a 6 kHz
I.F. filter is hardly different from demodulating SSB AM with a 2.7 kHz
filter. You are only losing 300 Hz of audio bandwidth doing that.
I got into the habit of running SSB mode to receive AM, particularly SW AM,
because
If you have the latest firmware on the KXPA100 it 5 watts or less out of the
KX3 and the KXPA100 is in bypass mode , if you increase the power from the KX3
above 5 watts the amp will then be in line and you will get a steady power
light.
Bob (G0UOI)
On 25 Jun 2016, at 17:05, Richard Thorpe
> Is there any reason to equip my my K3S with either the 6 kHz or FM
> filter roofing filters for AM reception or will the DSP filter do the
> job. I realize that if I want to tx AM I will need to install the
> 6kHz filter.
If you expect to receive AM as AM you will need either the 6 KHz
(AM)
FWIW, I listen to most SW and any weak AM signals in SSB mode. I have the 6
kHz I.F. filter but only use it on occasionally. IF you pass for now, you
can very easily add the 6 kHz filter later.
Your best initial investment would likely be the KBPF3A which gives you
optimum receiver sensitivity
I am going to order a K3S and have my filter selection figured out OK for CW
and SSB. However I want to do a little BCB and SWL listening on AM. At this
time no plans to transmit AM. I live in rural Alaska and there are no strong
BCB or SW broadcast stations close to my QTH. Is there any
>From today's Daily DX:
On Wednesday K8ZOA, Jack R. Smith, passed away from liver, kidney and
respiratory complications. He was both a lawyer and engineer working
for both the FCC and private practice law firms. Jack was an inventor
and created Clifton Laboratories. Earlier this month DX
This is a long shot, but anyone have either/both a kpa100 / kat100 that is
partially complete or inop and collecting dust ??
I'm thinking of adding an amp for my K2 and looking for something I can get
very Inexpensively and fix up...
I am aware of the Italian and Chinese amp's on eBay
Are any of the fault lights lighting?
What is displayed in the KX3 display?
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KXPA100-tp7619264p7619265.html
Sent from the Elecraft mailing list archive at Nabble.com.
Just set up my summer station KX3-KXPA100 and the “ON” LED on the KXPA100 is
blinking slowly and I’ve forgotten what this means and how to clear it. Help
please. Thank you.
K6CG/VE1 for the summer
__
Elecraft mailing list
Home:
A quick visit to the home page leads to the correct link quickly:
http://wilcoxengineering.com/kpa100-in-ec2/
the dashes were just left out. Hope this helps.
73, Byron N6NUL
On Sat, Jun 25, 2016 at 8:33 AM, ab2tc wrote:
> Hi,
>
> For other people's info, the link Alan
Hi,
For other people's info, the link Alan provided below doesn't work (page not
found).
AB2TC - Knut
Elecraft mailing list wrote
> Alan
>
> Do you still have some pictures available? I purchased a K2 with EC2 with
> amp and tuner installed but no info from the previous owner how to
>
Besides the parts access issues, another consideration is keeping it
buildable. If the K2 were to be updated any further, it might go out of
reach as a buildable-by-mortal-hams kit with discrete components. In fact,
there are compromises in the rig already to keep it easy to build, I'm
thinking
Hello Bill
I am interest in the J38 you have for sale.I can paypal to your email
address.what are the details.
Ron
AK4JL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Can the FIL default display "FIL ADJ" be replaced with the current
setting? This change will allow viewing the BW without the need to tune
the BW.
Using MCU 2.66 / DSP 1.48
John KN5L
__
Elecraft mailing list
Home:
Hi All,
For sale, K SN 2680.
Includes:-
General Coverge RX
700, 2.8K, 6.0 and 15K 8 pole filters.
100 Watt
ATU
Upgraded DSP Board
SS screws
P3 SN 150
K144XV internal 2 meter module.
HM2
Original owner, non smoker, little operating time. Built by professional
electronics technical officer.
AUD
27 matches
Mail list logo