Martin,
Contact Elecraft support. I purchased a pair of the same MOSFET's a
couple of years or so ago when my K3 did the same as yours...
Unfortunately mines done it again just recently, so this time I'm ordering
a few spares.
73
Matthew
VK5ZM
On 10 April 2018 at 14:32, Martin Sole
Hi,
Both output devices in the LPA, Q4 and Q5, RD15HVF-1, show low ohms gate
to source, one is 2.4 ohms the other 4.6 ohms.
Anyone have a recommended source? I don't think these are available
locally, I'll need to get a couple shipped in from US or elsewhere most
likely.
Thanks
Martin,
Thank each of you for your comments. I will order the Rotor EZ.
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of marvwhee...@nwlink.com
Sent: Monday, April 9, 2018 5:18 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] OT - Rotor
Have you tried doing a TX GAIN calibration? It will likely fail given what you
are seeing but it's another step to try.
GL & 73,
Brian, K0DTJ
> On Apr 9, 2018, at 18:11, Martin Sole wrote:
>
> Hi,
>
> I can see output at the XVTR OUT jack. Using direct input on the
Hi,
I can see output at the XVTR OUT jack. Using direct input on the LP-100A
meter it shows output varyng in sympathy with the output level control
and a setting of L 1.00 gives pretty much 1dBm on the LP-100A. Lowest I
can read is around -12dBm and highest about +3dBm before the K3 switches
Hi,
I see about 1.17A in receive and only 1.8A in TX TUNE mode with the the
PWR control set at 110W.
Martin, HS0ZED
On 10/04/2018 07:38, Al Lorona wrote:
Martin,
Does the K3 draw any current from the power supply when you go into
TUNE? If so, then maybe the power meter is bad.
If not,
Hi,
Well I've been through all of the operational settings. CONFIG : TUN PWR
is set to NOR and I can vary the power with the power control but the
output meter display stays at 0.0 and the VSWR displays only - - . I had
a settings save from about a month ago but uploading that hasn't changed
Had the same thing happen here to my K3s but only with the high power board.
The low power 0 to 12 watt board continued to work normally. Tried a transmit
gain calibration with no effect.
I sent it back to Elecraft and they replaced both the low and high power boards
with revisions they deemed
Raised hand.
Wes N7WS
On 4/8/2018 3:45 PM, Edward R Cole wrote:
hmmm, well I'm hearing a lot of opinion expressed.
First off, how many of you have acctually built ckts for10-GHz+? (show of
hands) And of you who did, how many worked the first time as designed without
"tinkering"?
Is anyone using Rotor EZ and N3FJP together and if so does it work
seamlessly.
Thanks in advance.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
The Aoril NAQCC sprint is this coming Tuesday evening local time (April 10th,
EDT - 8:30-10:30PM, CDT - 7:30-9:30PM, MDT - 6:30-8:30PM, PDT - 5:30-7:30PM),
which translates as Wednesday, April11th, 0030 to 0230Z in all cases.
For all the "official" information, please go to:
Hi All!
I have moved the Pro Audio Engineering website to a new server, so there
will be a service interruption between now and Tuesday morning. If you
wish to peruse our wares, please try again tomorrow.
Thank you!
Howard Hoyt
www.proaudioeng.com
That's what I would try next.
73,
Victor, 4X6GP
Rehovot, Israel
Formerly K2VCO
http://www.qsl.net/k2vco/
Vic
On 9 Apr 2018 20:18, Brian Hunt wrote:
Do you have a saved CONFIG file you can reload? Maybe those data got
garbled by the nonstandard shutdown? GL!
Brian, K0DTJ
On Apr 9,
I tried that on my K3 and it will me dial it down to 00.1 - then it says 'nor'.
At 00.1 mine shows 00.1 RF out in TUNE.
- 73 and good DX de Mike, K6MKF, Past President - NCDXC
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> On Behalf
Hi,
Is it possible that menu "Tune PWR" is set to 0?
Tom
-Original Message-
From: Martin Sole
Sent: Monday, April 9, 2018 12:35 PM
To: k...@arrl.net
Cc: Elecraft Discussion List
Subject: Re: [Elecraft] K3 Apparent PA failure ?
I’m pressing TUNE. Mode VOX etc shouldn’t matter.
Martin,
In TX TEST mode the “TX” symbol on the right end of the display will flash
about once per second. No need to try turning it On to see if it’s on or not.
Sent from my iPhone
...nr4c. bill
> On Apr 9, 2018, at 11:56 AM, Dave Cole (NK7Z) wrote:
>
> Press and hold the right side
Do you have a saved CONFIG file you can reload? Maybe those data got garbled
by the nonstandard shutdown? GL!
Brian, K0DTJ
> On Apr 9, 2018, at 08:31, Martin Sole wrote:
>
> Hi,
>
> My K3 died today, somehow. The radio works fine on receive and appears to
> transmit
For what?
Sent from my iPhone
...nr4c. bill
> On Apr 9, 2018, at 1:07 PM, Roy Koeppe wrote:
>
> VOX needs be ‘ON.’
>
> Roy K6XK
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>
VOX needs be ‘ON.’
Roy K6XK
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please
This should not matter pressing the XMIT button.
John
John KK9A
Dave Sublette k4to.dave at gmail.com
Are you in CW mode? If so, is VOX enabled?
K4TO
>>
>> On 04/09/2018 08:31 AM, Martin Sole wrote:
>>
>>> Hi,
>>>
>>> My K3 died today, somehow. The radio works fine on receive and appears
>>>
I’m pressing TUNE. Mode VOX etc shouldn’t matter.
Martin, HS0ZED
Sent from my iPad
> On 9 Apr 2018, at 23:32, Dave Sublette wrote:
>
> Are you in CW mode? If so, is VOX enabled?
>
> K4TO
>
>> On Mon, Apr 9, 2018 at 12:20 PM, Martin Sole wrote:
>> Not
Are you in CW mode? If so, is VOX enabled?
K4TO
On Mon, Apr 9, 2018 at 12:20 PM, Martin Sole wrote:
> Not in test mode :(
>
> I get the red TX led bit the display show 0w and - - where the VSWR
> display would be when I press TUNE in TX NORM.
>
> Martin, HS0ZED
>
>
>
> On
Not in test mode :(
I get the red TX led bit the display show 0w and - - where the VSWR
display would be when I press TUNE in TX NORM.
Martin, HS0ZED
On 09/04/2018 22:56, Dave Cole (NK7Z) wrote:
Press and hold the right side of the band-switch over "Test" and make
sure you are not in test
Press and hold the right side of the band-switch over "Test" and make
sure you are not in test mode.
You should see the words:
"TX TEST"
or
"TX NORMAL"
It should say "TX NORMAL".
73s and thanks,
Dave
NK7Z
https://www.nk7z.net
On 04/09/2018 08:31 AM, Martin Sole wrote:
Hi,
My K3 died
Hi,
My K3 died today, somehow. The radio works fine on receive and appears
to transmit just there is no power indication on my external meter or on
the front panel when pressing TUNE. There is ALC indication but no power
out indication.The only thing I did different was to switch off the
Barry is in VK. If he operates from the middle of nowhere, local noise is
nonexistent and local activity is extremely sparse. It means you hear lots
of weak stations, most of which you have little chance of working unless you
have good antennas and run power. So preamp is a plus in receive but it
If you have any screen shots of RFI on your P3, please send them to me
for my RFI snapshot page located at:
https://www.nk7z.net/rfi-snapshots/
I am looking for known sources, not unknown sources...
--
73s and thanks,
Dave
NK7Z
https://www.nk7z.net
Hey, Ed,
Piece of cake! (10 Ghz) But I worked up to it slowly. Building gear for
the lower microwave bands sure helped with wrapping my head around the
problems encountered there. I loved pipe cap filters!! Now I am having
a real hard time getting my 160 meter receive antennas to work!! I
For digi operation, I'd agree with you. For casual CW/SSB, even at 10
watts, highly unlikely.
John AE5X
https://ae5x.blogspot.com
Another box with the heatsink enclosed in a space with no ventilation.
It looks neat, but it is a great way to cook those power transistors.
wunder
K6WRU
29 matches
Mail list logo