I’d like to know too. I’ve never been able to get it to work. Sometimes it
starts saving snd hangs up; sometimes it doesn’t start.
Victor 4X6GP
> On 26 Sep 2020, at 3:42, w4sc wrote:
>
> I’ve read the manual, tried at least 10 memory sticks (a very BAD location
> for the USB, some don’t
OK, so the only thing I do with ethernet is connect to the Internet
via a router.
So would the K4 ethernet connect via the router using a local network
to communicate with my computer? I have that option to network my
printer between multiple computers.
One related question will the
Mike,
I have a MX-P50M and when Keyed from the Keyline on ACC2 (on the Ring and
Sleeve of ACC2) works. The spec on the Keyline is 30V, 100 mA max, open
drain. If hooked up the two work fine, with the KX3 set to 5Watts.
However, I did blow the 2n7002 transistor that drains the Keyline at ACC2,
I’ve read the manual, tried at least 10 memory sticks (a very BAD location for
the USB, some don’t fit because of VGA cable.
What is the secret?
Ben W4SC
Sent from Mail for Windows 10
__
Elecraft mailing list
Home:
Mark,
Do you have a schematic for the XV222? I looked on their site and
could not come up with one.
72
Howard Kraus, K2UD
-From: "Don Wilhelm"
To: "k2qo"
Cc:
Sent: Friday September 25 2020 2:44:03PM
Subject: Re: [Elecraft] XV222 RX is Dead,
Does anyone have a link or step by step document to configure a remote setup?
73
Steve KD2OM
Sent from my ec iPhone.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Mark,
Sorry about your failed effort. There is little in the RX path other
than Q3 and U1 that is not also used in TX.
If you have equipment that can do signal tracing at 222MHz, just trace
the signal path. There should be a significant increase in RF voltage
at the output of Q3 and more
Doug,
This is one of the problems with using info from the wayback machine.
That was one initial 'cure' that worked only marginally.
Elecraft released a mod kit that works well. Put the parts from the kit
in, and yes, C180 is to be removed in the process.
Go back to setting L34 for best S/N
> I receive audio via the USB just fine with a plug in the LINE IN jack
>
> What am I missing?
Line In is *transmit* audio. Connecting to Line IN will prevent you
from *transmitting* from "Speaker (USB Audio CODEC)".
73,
... Joe, W4TV
On 2020-09-24 10:25 PM, Rich wrote:
Fred's book
Don and gang,
I replaced Q3, U1 and the ADEX mixer. Results? Transmit works FB as before
and the RX still has no sensitivity. No change at all. I ran through the
setup related to the RX section and one thing stands out.
Part VIII: RX Input Alignment
Trimmer cap C1 has no effect on the AC
If you try to keep the humidity in your house above about 40%, it MAY help
for those shocks you get when you shuffle across the room and turn on an a
light switch or something grounded.
You might notice that you don't get those shocks in the summer, since the
ambient humidity is usually much
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
On 2020-09-24 19:21:-0400, David Haines wrote:
>http://www.emcesd.com/pdf/eos93.pdf
>
>73,
>david KC1DNY
The article is dated 1993.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
13 matches
Mail list logo
