Re: [Elecraft] KXPD2 screws

Refer to the instruction sheet for the KXPD2: https://ftp.elecraft.com/KX2/Manuals%20Downloads/E740295%20KXPD2%20Paddle%20Instructions%20Rev%20C.pdf This states that the thumb screws are 4-40 half-inch long. I regret greatly my purchase of the KXPD2 in 2017. It is the worst iambic key

Re: [Elecraft] KXPD2 screws

Hi Al,The screws are 4X40 1/2 " length. Elecraft # is E700245.. I highly recommend using these because of the printed circuit board behind the case and impossible to see. You might try the British Elecraft distributer.Oh, the KXPD3 uses the same screw..73,Jim HK7sss In a message dated

[Elecraft] Service delays?

__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:

Re: [Elecraft] KXPD2 screws

Al, The screw size is 6-32 (not metric). But do contact Elecraft to obtain the proper screws. If the screws project too far inside the KX3 enclosure, the PC board will be damaged. I do know it can take a while to get items 'across the pond', but for the health of your KX3, get the proper

[Elecraft] k2 spectrogram problems solved

thanks to all for the reply, was an issue in the privacy settings win10 k2 working great now 73 carlos on6cn -- mvg carlos popelier regards carlos popelier __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft

Re: [Elecraft] KXPD2 screws

I can't help you with the screw size, but I recommend contacting Elecraft on this. The point on one of the screws is ground down to eliminate some type of physical interference in the KX3. It would be wise to use the screws that come with the paddle. 72 Howard Kraus, K2UD

[Elecraft] KXPD2 screws

Hello, I’ve been offered a secondhand KXPD2 key for my KX3 but it’s missing the screws to attach it to the radio’s case. I’m loath to experiment with random fasteners so could someone please inform me what size the retaining screws are? Thank you, Al G4VSQ Sent from my iPhone

Re: [Elecraft] [Elecraft-K4] 80 Meter Elecraft Net moving, plus the rest of the nets ... corrections

The Elecraft Nets -- The Elecraft Nets -- 20 Meter SSB Elecraft Net Sunday 14.3035 +/- MHz at 1800Z 40 Meter SSB Elecraft Net Sunday 7.280 MHz at 19:000z 20 Meter CW Elecraft Net Monday 14.050 MHz

Re: [Elecraft] K3s/KPA500 communication issue?

Thanks to all who offered suggestions. Let me touch on some: * CONFIG:PWR SET is PEr bAnd - Was and is. * Reload firmware - Done; no change. * TX GAIN CAL on the K3 - Not yet; will look into this. * Plug/replug cables - On the to-do list. * Other software sending commands - The problem has

[Elecraft] 80 Meter Elecraft Net moving, plus the rest of the nets ... corrections

The Elecraft Nets -- The Elecraft Nets -- 20 Meter SSB Elecraft Net Sunday 14.3035 +/- MHz at 1800Z 40 Meter SSB Elecraft Net Sunday 7.280 MHz at 19:000z 20 Meter CW Elecraft Net Monday 14.050 MHz

Re: [Elecraft] K3s/KPA500 communication issue?

This question has come up several times over the years, and I have always followed the threads closely, since I have occasionally had the same issue. The consensus seems to indeed involve a communication issue: the KPA500 sends a signal to the K3 when its operational status changes, but for

Re: [Elecraft] WSJTX Weird shift on different bands

HOWEVER, on 15M (21.074), 17M and 12M - with this setup, I get NO decodes, and on the P3, I see the passband in the CENTER of the display, and the signals are all to the right of the passband. Check your data sub-mode (DATA MD) *one each band*. The sub-mode is stored *per band* and it

[Elecraft] Elecraft Support Reply Time

What's the general time it's taking Elecraft support to reply to e-mail queries? Obviously, this has been a crap year, and normal expectations don't apply. 73, Steve NN4X -- Steve Sacco NN4X Narcoossee, FL EL98jh __ Elecraft

[Elecraft] WSJTX Weird shift on different bands

I'm certain I'm doing something stupid, clearly I don't understand the SSB/data shifting going on; but, I can't seem to figure this out. I'm running a K3 with a SignaLink USB connected to the rear-panel and WJSTX, primarily for FT8 (although see below). WSJTX is set for "Ham Radio Deluxe"

Re: [Elecraft] KPA1500 ATU band/bin operation

Thanks for the good explanation Dick.  It got by me that the bins are storing the ant port# along with the tuner settings.  That should work well having 2 antennas on every band if needed.  Adding a 3rd might be cumbersome but more then I need for now anyway... I'll think about that later.